PULSE EIGHT MS SERIES One IP Transceiver User Guide
- September 4, 2024
- PULSE EIGHT
Table of Contents
MS SERIES One IP Transceiver
“`html
Specifications:
-
Product: Pulse-Eight OneIP Transceiver
-
Capabilities: AV-over-IP solution for distributing UltraHD 4K
HDMI 2.0 video with HDR support -
Network: 1Gbps Ethernet network
Product Usage Instructions:
Core Switch Configuration:
-
Log in to the Pakedge Switch web interface using default
credentials (admin/password). -
Create a new secure username and password.
-
Set the switch to a static IP address or DHCP reserved from the
DHCP server if needed.-
Select Configure > LAN > Static mode and set IP address,
Subnet Mask, and Gateway. -
Save settings by clicking Apply.
-
Log in using the new IP address and credentials.
-
-
Enable IGMP Snooping under Advanced settings and configure VLAN
settings for OneIP devices. -
Configure Multicast Router VLAN settings and set Unregistered
Multicast Behaviour to Drop. -
Ensure IGMP Snooping Querier is enabled with IGMP Version set
to V2.
FAQ:
Q: Can I connect OneIP devices before completing the
configuration?
A: No, it is important to complete the configuration first to
avoid network issues due to multicast data flooding.
Q: What should I do if I encounter issues during the
configuration process?
A: If you encounter any issues, refer to the user manual for
troubleshooting steps or contact customer support for
assistance.
“`
ONEIP NETWORK CONFIGURATION GUIDE – PAKEDGE MS SERIES V 1.0
INTRODUCTION
The Pulse-Eight OneIP transceiver is an ultra-low latency, AV-over-IP solution
capable of distributing UltraHD 4K HDMI 2.0 video (18Gbps), with support for
HDR, over a 1Gbps Ethernet network. The following is a step-by-step tutorial
for configuring the Packedge MS series switches for use with Pulse-Eight OneIP
TRX units. Please follow the instructions below before connecting any OneIP
devices to the switch.
SUPPORTED PRODUCTS
· Pakedge MS series switches. Note: Please note this has only been tested with
MS2424 at the present time.
IMPORTANT NOTES!
Do NOT connect any OneIP devices to the switch before configuration is
completed, doing so may cause the switch to run slow or crash due to multicast
data flooding the network.
1
ONEIP NETWORK CONFIGURATION GUIDE – PAKEDGE MS SERIES
pakedge Router
Secondary Network Switch
Core Network Switch
AVoIP Switch
CORE SWITCH (OR SINGLE SWITCH) CONFIGURATION
Log in to the Pakedge Switch web interface. The Pakedge MS switches are set to
DHCP by default; to find an IP address, you need to scan the network or check
the DHCP server; if no DHCP server is available, the switch will default to
192.168.1.205.
1. Log in to the Web UI. The default credentials are admin and password. 2.
Create a new secure password and username. 3. Set the switch to a static IP
address or DHCP reserved from the DHCP server (optional).
a. Select “Configure” then under “LAN” change mode to Static and set the
desired IP address, Subnet Mask, and Gateway.
b. Save the settings by clicking “Apply” in the top right corner of the
screen. The switch will reboot and use the static or reserved IP address.
c. Once “Submitting” shows on the screen, close the browser window. 4. Log in
to the Web UI using the new IP address, username, and password. 5. From the
main menu, select “Advanced” and then `IGMP Snooping’ under the switching
section.
2
ONEIP NETWORK CONFIGURATION GUIDE – PAKEDGE MS SERIES 6. Enable the IGMP
Snooping Global Configuration and Status toggle switch and click “Apply”. 7.
Move to the VLAN Status page, and click “OPTIONS” button to add a VLAN entry.
8. Select the VLAN ID on which the OneIP devices are connected and disable
Fast Leave for all switches.
3
ONEIP NETWORK CONFIGURATION GUIDE – PAKEDGE MS SERIES 9. Click the Apply
button in the top right corner of the page. 10. On the Multicast Router VLAN
Configuration page, enable MRouter Learning on all ports and click Apply.
11. Go to Advanced > Unregistered Multicast Behaviour > Configuration. Set
Unregistered Multicast Behaviour Configuration to Drop. Click Apply.
12. If you notice an entry for EXC_default_list under the Exemptions list,
proceed to the next steps. If not, then your configuration is complete.
13. Click on the Interface Configuration tab, then select Options and Edit.
4
ONEIP NETWORK CONFIGURATION GUIDE – PAKEDGE MS SERIES 14. To select all
entries in the EXC_default_list, click the box next to Interface. Then, click
Edit Selected.
15. Click the “x” in the EXC_default_list object to delete it.
16. Click Save and then Apply at the top of the page. 17. Go to Advanced >
IGMP Snooping Querier > Configuration. Click Enable and make sure the IGMP
Version is set to V2, then click Apply at the top of the page. 18. The Querier
IP address should be set to the same IP address as the switch.
5
ONEIP NETWORK CONFIGURATION GUIDE – PAKEDGE MS SERIES 19. Select the VLAN
Configuration Tab in the IGMP Snooping Querier menu. 20. On the right side,
select the three dots under OPTIONS and choose Add’. 21\. Confirm VLAN 1 is selected and enableQuerier Election Participation’.
The VLAN IP can be 0.0.0.0. 22. Then, click Add button.
23. Click the Apply button in the top right corner of the screen. 24. This is
all that is needed for a single switch setup.
MANUAL VERSION HISTORY
V1.0 – 8th February 2024. First version. 6
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>