PULSE EIGHT P8-HDBT2-U-FFMJ66-KIT neo XSR Video Matrix User Guide
- June 17, 2024
- PULSE EIGHT
Table of Contents
PULSE EIGHT P8-HDBT2-U-FFMJ66-KIT neo XSR Video Matrix
CHECK WHAT’S INSIDE THE BOX
- 1 x neo:XSR Chassis
- 1 x Power Cord
- 1 x IR Blaster Cable Pack
- 1 x Rack Mounting Kit
- 1 x Quick Start Guide
IMPORTANT!
- Please read the instructions before attempting to install or operate this equipment.
- Visit help.pulse-eight.com to download the latest product manual, additional documentation, and configuration tools.
PANEL DESCRIPTIONS
System Health LED: Indicates matrix health.- RED – It is powering on or fault found.
- GREEN – The system is healthy.
- Network LED: Indicates the matrix network connection. RED – No network cable is connected.
- AMBER (Flashing) – It is discovering the IP address. AMBER (Solid) – The network has the IP but cannot ping the router.
- GREEN (Flashing) – The network cannot reach the internet.
- GREEN (Solid) – The network is healthy.
- Cloud LED: Indicates the matrix connection to the Pulse-Eight Cloud.
- RED – It is not connected to the cloud.
- GREEN – It is connected to the cloud.
- Power Connector: Use with the supplied power cord to connect the power.
- IR IN and OUT Ports connect as required.
- The IR IN port (black) can be used to accept and distribute IR signals from a controller using a P8-IR-Optocable, as well as distribute IR signals back to the matrix using a compliant Pulse-Eight IR Receiver.
- The IR OUT port (grey) is used to control the connected HDMI® Source device (STB, Blu-Ray, etc) using a compliant Pulse-Eight IR Emitter.
- Audio Outputs: Optical and Digital Coax options for Audio Breakouts.
- HDMI IR IN: connect as required.
- The Input IR port (black) can be connected to receive and distribute IR signals from a connected HDMI® extender.
- HDBaseT Outputs: Connect the appropriate *Category cable to each output. These cables should then be connected to a neo Receiver at each sink device. (TV/Amplifier etc.).
- *Category cable: Cat5e minimum requirement. Cat6 or higher category recommended.
- HDMI Inputs: Connect the appropriate high speed HDMI cable to each input. These cables should then be connected to the Source device. (Blu-Ray player etc.)
- Reset: Factory reset – Please use only when instructed by our customer service team.
- Ethernet: Connect to network – Required for connection to Web Interface, Third Party Control, and Cloud Remote Monitoring Portal.
- HDMI Outputs: Connect the appropriate high speed HDMI cable to each output. These cables should then be directly connected to each Sink device. (TV/Amplifier etc.)
INSTALLATION
Installing In A Rack
Attach the rack ears to the front sides of the matrix using the provided screws.- Install into the rack and connect cabling according to the mode of operation – as described below.
WARNING : To prevent damage, it is important to ensure adequate ventilation space on the sides of the matrix, especially on the ventilation openings on the side of the product enclosure.
Connecting The Inputs
Connect HDMI cables from your video sources (e.g. Blu-Ray player) to the HDMI inputs of the matrix.- If required, connect the compatible IR Flasher (Emitter/Transmitter) cable to the ‘OUT’ port (grey) on the matrix and the IR bud placed over the source device’s IR window.
Connecting The HDBaseT Outputs
Connect the appropriate category cable (Cat6 or higher recommended) to each HDBaseT output ports that you require.- Complete the connection by attaching the other end of the Cat cable to a supplied neo-Receiver’s ‘HDBaseT In’ port. The neo Receiver should be situated at the output end (i.e. next to the TV).
- Connect HDMI Out on the neo Receiver to the sink device (i.e. TV) using a high-speed HDMI cable.
- If required, connect the IR Receiver to the neo-Receiver’s ‘IR IN’ port (black) – and place the IR bud on the underside of the sink device (i.e. TV).
- If required, connect the compatible IR Flasher (Emitter/Transmitter) cable to the ‘IR OUT’ port (grey) on the neo Receiver with the IR bud placed over the sink device’s IR window.
WARNING!
Please make sure to use a compatible 5V IR receiver/transmitter on this
product.
Connecting The HDMI Outputs
For Output ports 5 and
6, connect sink devices (e.g. TVs) directly via high speed HDMI cables.
Connecting The Audio Outputs
If you wish to use the audio outputs from the matrix, please connect cables to
the relevant output. There are 6 output zones, where each zone features
Optical and Digital Coax options that can work simultaneously.
There are two audio modes of operation: Source Mode and Sink Mode. By default,
when you first install the matrix, the unit is set to sink mode with each zone
set to passive.
IMPORTANT: The matrix needs to be set to Sink mode or Source mode according to the installation’s requirement, and wired accordingly. Please ensure that you set up the matrix to the correct audio mode in the Audio Control tab of the Web Interface.
Sink Mode VS Source Mode
-
Sink mode is the preferred method when setting up the neo:XSR in an installation that does not have a dedicated audio matrix switch.
Sink mode allows for the matrix to automatically manage the audio routing from any of the inputs to the corresponding audio output zone, so that is matches the video displayed on that same output zone. The “audio always follows the video”. -
Source Mode is generally used in larger installations where the input audio is being fed directly to one or more dedicated audio matrices (e.g. ProAudio switch). In this mode, the audio outputs zones A to F are locked to HDMI inputs 1 to 6 respectively.
Connecting The Network
It is necessary to
connect a standard Ethernet cable (Category 5e/6/7) from the matrix’s
‘Ethernet’ port to your router or network switch. Crossover cables are not
supported.
Note: A network connection is required for supporting full control/remote monitoring features of the product.
Turning On The Matrix
-
Insert the supplied power cord and plug into the AC mains. -
Turn ON the power switch.
-
As it powers ON, the front panel LEDs (System Health, Network, Cloud) will illuminate momentarily before it begins its initialization sequence.
Note: The initialization process takes between 20 seconds and up to 2 minutes. However, it is possible that a firmware update may be available the first time the unit is powered ON – in this instance the matrix may take longer to initialize. If both the System Health and Network LEDs flash (orange/green) quickly together then a firmware update is being applied. Please wait and do not disconnect the power until this update has completed. -
Once initialization has been completed, the System Health, Network and Cloud LEDs should all appear ON (green).
-
Check the LED status on the attached neo Receivers to ensure correct installation and connection.
Note: When a link is established between the Matrix and the Neo Receiver, the orange LED on the HDBaseT port on the Neo Receiver will illuminate (at this point you can assume that the neo receiver is powered on).
This guide helps you to install and use your neo:XSR for the first time.
Go to help.pulse-eight.com for additional
information on this product including important technical information not
provided in this document and warranty SCAN FOR HELP terms & conditions.
neo Web Interface
The Web Interface can be accessed using a computer connected to the same router/network as the matrix and by visiting www.gotomymatrix.com in your web browser.
The front page of the
web interface features a user-friendly drag and drop for video routing and
display showing all available inputs and outputs.
When setting up the matrix, it is important that the installer can access the admin menu on the Web Interface to configure the matrix according to the installation’s requirements. This is accessed by clicking the Admin hyperlink and entering ‘admin’ in the password on first install.
Monitoring Portal
Note: During the
installation, it is recommended to enter your Installer ID in the Web
Interface.
If you do not already have an Installer ID then you will need to request an
account. Please contact us via email at cs@pulse-eight.com.
SAFETY PRECAUTION
Please read the full manual instructions before attempting to install or
operate this equipment.
Please keep the following in mind as you unpack and install this equipment:
- Always follow basic safety precautions to reduce the risk of fire, electrical shock, and injury.
- To prevent fire or shock hazards, do not expose the unit to rain, or moisture or install this product near water.
- Never spill liquid of any kind on or into this product.
- Where possible, install the matrix towards the top of the rack to avoid the unit overheating.
- Only use the supplied IEC cable.
- Never push any objects into this product through any openings or empty slots in the unit as you may damage parts inside and/or cause an electrical shock.
- Do not allow anything to rest on the power cabling and avoid putting the weight of any kind on it.
- To protect the unit from overheating do not block any vents or openings in the unit housing that provides ventilation. Allow sufficient space for air to circulate around the unit.
- This product is intended for use in a clean (dust-free) residential environment.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored
in a retrieval system, or any of its part translated into any language or
computer file, in any form or by any means (electronic, mechanical, magnetic,
optical, chemical, manual, or otherwise) without express written permission
and consent from the manufacturer.
© Copyright 2023. All Rights Reserved. Version 1.0 – September 2023
Pulse-Eight Limited, 8-12 Alder Hills, Poole, Dorset, BH12 4AL. UK support @pulse-eight.com | www.pulse- eight.com | +44 (0)1202 413 610
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>