pixthink M1 1080P Full HD Projector Digital Projector User Guide

pixthink M1 1080P Full HD Projector Digital Projector

Important Safety Instructions

• Read and understand all instructions before you use this device.
• Do not change any settings that are not described in this manual.
• If physical injury, loss of data, or damage is caused by failure to follow instructions, the warranty does not apply.

Setup

1. To reduce the risk of fire and/or electric shock, do not expose the device to rain or moisture, or objects filled with liquids, such as vases, should not be placed on the device.
2. Do not place the device in areas susceptible to excessive dust and dirt or near any appliance generating a strong magnetic field.
3. To prevent overheating, do not block or clog the ventilation openings.
4. Never place the device in a confined space. Always leave enough space around the device for ventilation.
5. Protect the device against direct sunlight heat, large temperature fluctuations and moisture.
6. When the device runs for a long period of time and the surface becomes hot, shut it down and unplug the power cord. Resume operation only after the device has cooled.
7. Always handle the device with care. Avoid touching the lens.
8. Never place heavy or sharp objects on the device or the power cord.
9. To avoid electric shock, do not disassemble.
10. Only use attachments or accessories specified by the manufacturer.
11. Avoid extreme vibration. It may damage the internal components.
12. Do not allow children to handle the device without supervision.
13. Under the following conditions, a layer of moisture can appear inside the device which can lead to malfunctions;
14. If the device is moved from a cold to a warm area.
15. After a cold room is heated.
16. When the device is placed in a damp room. To avoid any moisture, seal the device in a plastic bag before moving it to another room, and wait for one to two hours before you take it out of the bag.

Power Supply

1. Power off the device before removing the power supply from the socket.

2. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from this device.

3. Unplug this device if there are lightning storms or when unused for a long period of time.

4. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
   Before you make or change any connections, ensure that all devices are disconnected from the power outlet.

5. Never touch the power cable or the power connection with wet hands.
   Hearing Safety
   To avoid hearing damage, do not listen for extended periods at high volume. Set the volume at a safe level.

cleaning

1. Power off the device and remove it from the power supply before cleaning the surface.
2. Use a soft, lint-free cloth. Never use liquid, gaseous, or easily flammable cleansers (like sprays, abrasives, polishes, and alcohol).
3. Do not use any liquid cleaning agents to clean the lens as they may damage the protective coating on the lens.
4. Wipe the surfaces gently. Be careful that you do not scratch the surfaces.
5. Use lens cleaning paper to clean the lens of this projector.

Repairs

1. Do not make any repairs to the device yourself. Only have your device repaired by an authorized service center.
2. Improper maintenance can result in injuries or damage to the device.
3. Refer all servicing to qualified service personnel.

Class equipment symbol
This symbol indicates that the unit has a double insulation system.

IEC 60825-1:2014. Complies with IEC 62471:2006 Risk Group 2.

caution

1. Possibly hazardous optical radiation emitted from this device.
2. Do not stare at the operating beam. The bright light may hurt your eyes.

What’s in the box

1. Home entertainment projector (Ml) 8 Power adapter
2. Power cable
3. Quick start guide
4. Remote control

NOTE
Lamp life results will vary depending on environmental conditions and usage. Actual product’s features and specifications are subject to change without notice.
Some of the accessories may vary from region to region.
The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.

Overview

Front view

1. Power on/off
   Press and hold for one second to switch the projector on or off.
   When the projector is switched on, the LED turns green. When the projector is switched off, the LED turn red.

2. Lens
   Please don’t look directly into the lens.

3. Heat Sink
   Dissipate heat and control temperature.
   Rear View
   

4. Speaker

5. DC in

6. USB port

7. HD port

8. Audio output

9. IR Receiver

10. 1/4″ screw h ale for ceiling

Prepare the Remote Control

Please install two AAA batteries(not included) in remote control before use.

1. For first-time use, please remove the battery back cover of remote control.
2. To replace the batteries, slide to open the battery compartment, insert new batteries (matching the polarity (+/-) indicated), and close the battery compartment

Remote Control

1. Power on/off
2. Mute Button
3. Left/Right/Up/Down Arrow Button
4. Confirm/OK Button
5. Focus + Button
6. Focus – Button
7. Back Button
8. OSD Menu Button
9. Volume+ Button
10. Volume – Button

Getting Started

Placement

Place projector on a flat, stable foundation squarely in front of the projection surface. For best results, the projection surface shall be white and flat. The distance between this projector and the projection surface must be a minimum of 0.85 meter (30 inches) and a best of 2.2 meters (84 inches).

NOTE
You can also install your projector in the following ways: from the rear, front ceiling and rear ceiling. Make sure you select the correct Projection Mode option in this projector’s menu settings.

Select Projection Distance

PowerOn

1. Connect this proJector to the outlet by  using the provided power cord and adapter
2. Press the power button on the projector or on the remote control once.
3. Turn this projector towarde a flat,white projector surface.
4. To focus the image,adjuct by remote.

settings

Go through the setup process when you turn on this projector for the first time.
Press Menu” on the remote control to access the home menu, select.

Using the Projector

NOTE
Please press “Back”button to switch to the home page.

Play from HDMI Playback Devices
This projector can be connected to various HDMI devices such as a TV box, TV stick, DVD player. set-top box (5TB), gaming console or other devices.

To play from HDMI playback devices
Connect this projector to an HDMI playback device with an HDMI cable (not included).

Play from a USB Drive
With this projector, you can enjoy music, video, and pictures that are stored on a USB drive.

To play from a USB drive:
Insert a USB drive into the USB socket.

1. This projector will play the movie or picture or music you selected.
2. To stop play, please press “OK” button.

Play from External Devices

1. This projector can also be connected to external devices, including headphones and speakers.
2. When connected to external speakers, the built-in speaker system is disabled.

Play from External Devices

1. Use a 3.5mm audio cable or an adapter (not provided) to connect your headphones or external speakers.
2. Connect the other end of the cable to the AUDIO OUT port on this projector.
   You will hear audio from external devices.

NOTE
Before connecting headphones, turn down the volume to avoid straining your ears

Wired Mirroring (105 ONLY)

1. After powering on, click the “Screen Mirroring” on the home page to enter the screen mirroring mode. After a while, the Tip page will appear.
   

2. After power on, connect the original Apple USB cable to your iPhone or iPad, then connect the other end of the USB cable to the USB port of the projector.
   

3. Wait a few seconds and click KTrust this Computer” on your device. This projector will mirror the screen of the connected iPhone or iPad .

Wireless Mirroring (For 105 Devices)

1. Enter screen mirroring mode, turn on the WIFI on your iPhone and connect to “LOLLIPOP- xxxxx”,the password is n12345678n.
2. After connecting, use the mobile browser to visit “http:// 192.168.49.l”or scan the QR code to visit directly.
3. Select “WiFi-AP” on the browser screen, click “Scan”, and select the indoor WiFi that can be connected in the WiFi list.
4. Enter the WiFi password and click the “Connect” button to connect to the projector for Miracast.
5. Open NAirPlay Mirroring “on the phone to sync phone directly.

Wireless Mirroring (For Android Devices)

v

1. Android devices must have built-in wireless projection or muti-screen function.
2. After entering the mirroring screen, click the OK button on the remote control to switch between 10S and Android mirroring screens.

1. After powering on, click the “Screen Mirroring” on the home page and to enter the screen mirroring mode. After a while, the Tip page will appear. You can following the steps below.
   

2. Turn on WIFI, dropdown the menu and find screen cast.(some devices named in muti-screen)

3. Select “LOLLIPOP- xxxxx” to sync the phone.

Specifications

NOTE
Specifications and design are subject to change without notice.

• Model: M1
• Power consumption: 66 W
• Display technology: LCD+LED
• Native Resolution: 1920 x 1080P
• Light source: RGB LED
• Projection lmage size: 30-200 inches
• Throw ratio: 1.25:1
• Throw distance: 0.85m to 3.8m
• Speaker drivers: 3W x 2
• Remote control batteries: 2 AAA batteries(Not included)
• Dimensions (W x H x D): 137mm x 203mm x 130mm
• Weight: 1.44kg

Troubleshooting

1. Cannot turn on projector with the remote control?
   Make sure that this projector is connected to the power supply.

2. The remote control doesn’t work?
   Make sure the battery is already installed in the remote control. Replace the batteries.

3. Blurred image?
   Please adjust the clarity of the screen through the focus key on the remote control.

4. Rotate projection image?
   Press Menu to access the [Setting]> [Image] > [Projection] and switch to a correct state.

NOTE

This product complies with the requirements of the European Community.
This product can be used across EU member states. The following importer is the responsible party (contact for EU matters only)

This product is designed and manufactured with high quality materials and components, which can be recycled and reused.

This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling.
Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality. disposal service, or the shop where you bought this product.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

1. Reorient or relocate the receiving antenna.
2. Increase the separation between equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Manufacturer: ELMART CONSULTING LIMITED
Address: RM 2 3/F,RUBY COMMERCIAL BUILDING,480 NATHAN ROAD,KL,HONGKONG

EU Importer: Elmart GmbH
Address: Medienstr.37 (Gewerbepark), 47807 Krefeld,Germany 

Please Note
Any provided shipping labels must be used within 20 days from the date they’re issued by support.

Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

NOTE

1. 30 Day Money Back Guarantee for Any Reason.
   You may return your undamaged product and packaging within 30 days of purchase to receive a FULL REFUND for any reason. If the reason for return isn’t quality. related, the customer must pay for the return shipping.

2. 12 Month Warranty for Quality Related Issues
   The products are warrantied to be free from material and workmanship defects for 12 months from the date of purchase. Within this period, Your seller will provide a replacement and cover any return shipping costs for products that fail in normal use.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE:
   This equipment has been tested and found to comply with the limits for a Class B digital mdevice, pursuant to Part 15 of the FCC Rules.
   These limits are designed to provide reasonable protection against harmful interference min a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.
   However, there is no guarantee that interference will not occur in a particular installation.
   If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.
  The device shall be used with a minimum distance of 20cm from uses.

• The manual is subject to change without any prior notice.

• O5D options and pictures shown in this document may differ slightly from your product.

• Please read the instructions carefully before using the product and keep safely for future reference.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>