BAFANG E161 Electric Can Display User Manual
- September 3, 2024
- BAFANG
Table of Contents
BAFANG E161 Electric Can Display
Specifications
- Battery capacity indicator
- Speed indicator
- Support level indicator
- Walk assist mode
- Indicator for the lighting system
FAQs
Q: How can I check the battery capacity?
A: The battery capacity indicator on the display shows the remaining charge level of the battery.
Q: Can I use the walk assist mode while riding?
A: The walk assist mode is designed to help you walk with the bike, not for use during riding.
IMPORTANT NOTICE
- If the error information from the display cannot be corrected according to the instructions, please contact your retailer.
- The product is designed to be waterproof. It is highly recommended to avoid submerging the display underwater.
- Do not clean the display with a steam jet, high-pressure cleaner, or water hose.
- Please use this product with care.
- Do not use thinners or other solvents to clean the display. Such substances can damage the surface.
- Warranty is not included due to wear normal use and aging.
INTRODUCTION OF DISPLAY
- Model: DP E161.CAN BUS
- The housing material is PC+ABS and acrylic, as follows:
- The label marking is as follows:
Note : Please keep the QR code label attached to the display cable. The information from the Label is used for a later possible software update.
PRODUCT DESCRIPTION
Specifications
- Operating temperature: -20℃~45℃
- Storage temperature: -20℃~50℃
- Waterproof: IP65
- Storage room Humidity: 30%-70% RH
Functional Overview
- Battery capacity indicator
- Indication of support level
- Walk assistance
- Automatic sensors explanation of the lighting system.
- Indication for error messages
- Control and indication of the lighting system
- Bluetooth function
DISPLAY
- Battery capacity indicator
- Speed indicator
- Support level indicator
- Walk assist mode
- Indicator for a lighting system
KEY DEFINITION
E161 Display has three buttons: System On/Off Up and Down .
NORMAL OPERATION
Switching the System ON/OFF
- Press and hold (>2S) on the display to turn on the system.
- Press and hold (>2S) again to turn off the system.
Choice of Support Levels
When the display is turned on, press the or (<0.5S) button to switch to the support level, the lowest level is 1, and the highest level is 5. When the system is switched on, the support level starts at level 1. There is no support at level 0.
Headlights/backlighting
- Hold the (>2S) button to activate the headlight and taillights.
- Hold the (>2S) button again to turn off the headlight and taillight. (If the display is turned on in a dark environment, the display backlight/headlight will be turned on automatically. If the display backlight/headlight are turned off manually, they also need to be turned on manually afterward)
Walk Assistance
When your Pedelec is motionless, briefly press the button until the Walk
assistance indicator is displayed. At this point, long press button, the
Pedelec enters the walk assistance mode, and the indicator will flash. If
released the button will stop this, if
no operations within 5s will automatically return to 0 level. That is stopped
from the Walk assistance mode. (as follows)
Battery Capacity Indication
The battery capacity is indicated with 5 levels. When the lowest level indicator flashes that means the battery needs to charge. The battery capacity is shown as follows:
Troubleshooting
ERROR CODE DEFINITION
DP E161.CAN display can provide a warning for failures. The error code
flickers when an error is detected.
Note: Please read carefully the description of the error code. When the
error code appears, please first restart the system. If the problem is not
eliminated, please contact your dealer or technical personnel.
| Error | Declaration | Troubleshooting |
|---|
04
|
The throttle has fault.
| 1. Check the connector of the throttle whether they are correctly connected.
2. Disconnect the throttle, If the problem still occurs, please contact your retailer.
(only with this function)
05
|
The throttle is not back in its correct position.
| Check the throttle can adjust back into its correct position, if the situation does not improve, please change to a new throttle. (only with this function)
07
|
Overvoltage protection
| 1. Remove the battery.
2. Re-Insert the battery.
3. If the problem persists, please contact your retailer.
08
| Error with the hall sensor signal inside the motor|
Please contact your retailer.
09| Error with the Engine phase’s| Please contact your retailer.
10
|
The temperature inside the engine has reached its maximum protection value
| 1. Turn off the system and allow the Pedelec to cool down.
2. If the problem persists, please contact your retailer.
11
| The temperature sensor inside the motor has an error|
Please contact your retailer.
12
| Error with the current sensor in the controller|
Please contact your retailer.
13
| Error with the temperature sensor inside of the battery|
Please contact your retailer.
| Error | Declaration | Troubleshooting |
|---|
14
|
The protection temperature inside the controller has reached its maximum protection value
| 1. Turn off the system and let the pedelec cool down.
2. If the problem persists, please contact your retailer.
15
| Error with the temperature sensor inside the controller|
Please contact your retailer.
21
|
Speed sensor Error
| 1. Restart the system
2. Check that the magnet attached to the spoke is aligned with the speed sensor and that the distance is between 10 mm and 20 mm.
3. Check that the speed sensor connector is connected correctly.
4. If the error persists, please contact your retailer.
25
|
Torque signal Error
| 1. Check that all connections are connected correctly.
2. If the error persists, please contact your retailer.
26
|
Speed signal of the torque sensor has an error
| 1. Check the connector from the speed sensor to make sure it is connected correctly.
2. Check the speed sensor for signs of damage.
3. If the problem persists, please contact your retailer.
27| Overcurrent from controller| Please contact your retailer.
30
|
Communication problem
| 1. Check all connections are correctly connected.
2. If the error persists, please contact your retailer.
33
|
Brake signal has an error (If brake sensors are fitted)
| 1. Check all connectors.
2. If the error continues to occur, please con- tact your retailer.
| Error | Declaration | Troubleshooting |
|---|---|---|
| 35 | Detection circuit for 15V has an error | Please contact your retailer. |
36
| Detection circuit on the keypad has an error|
Please contact your retailer.
37| WDT circuit is faulty| Please contact your retailer.
41
| Total voltage from the battery is too high|
Please contact your retailer.
42
| Total voltage from the battery is too low|
Please contact your retailer.
43
| Total power from the battery cells is too high|
Please contact your retailer.
44| Voltage of the single cell is too high| Please contact your retailer.
45
| Temperature from the battery is too high|
Please contact your retailer.
46
| The temperature of the battery is too low|
Please contact your retailer.
47| The SOC of the battery is too high| Please contact your retailer.
48| The SOC of the battery is too low| Please contact your retailer.
61
|
Switching detection defect
| Please contact your retailer. (only with this function)
62
|
Electronic derailleur cannot release
| Please contact your retailer. (only with this function)
71
|
An electronic lock is jammed
| Please contact your retailer. (only with this function)
81
|
The Bluetooth module has an error
| Please contact your retailer. (only with this function)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>