evolite WI-PAR 12X12W RGBWA-UV 6 in 1 ip65 Battery Projector User Manual
- June 12, 2024
- evolite
Table of Contents
evolite WI-PAR 12X12W RGBWA-UV 6 in 1 ip65 Battery Projector
Safety Instruction
WARNING !
Before use, and before installing this fixture, read carefully user manual,
and follow the safety precautions listed.
WARNING !
Very high level light output. DO NOT LOOK INTO THE BEAM.
DANGER !
Hazardous voltage. Risk of electric shock!
ALWAYS disconnect the fixture from power for servicing, for cleaning or
installing.
Do not connect this unit on a dimmer power pack.
Protect the unit from rain or moisture.
WARNING !
Burn Hazard. Do not touch. Very hot surface
The fixture becomes hot during use and remains hot 10 min after use . Do not
touch the unit.
WARNING !
Fire Hazard!
Keep flammable materials away from the fixture. Do not operate the fixture
with ambient temperature over 40°C.
DANGER !
Safety Hazard. Risk of injury.
This evolite unit must be installed by professional people. If suspended, make
sure the structure and the hardware used for this suspension is secured. This
Hardware must support at least 10 times the weight of the device suspended.
Ensure public is not looking at the beam. Do not try to repair the fixture by
yourself. Contact a professional repair service.
Introduction
Thank you for selecting this professional fixture from evolite
This new intelligent Moving Wash will provide you reliability, latest
features, and professional lighting effects for a long period of time.
This evolite fixture is complying with European standards: EN60598-1:2008+A11:2009 EN60598-2- 17:1989+A2:1991 et RoHs.
Device Description
- LED: 12 LED 12W RGBWA-UV 6-in-1
- Power consumption: 160W
- DMX channels: 10 / 8 / 6 DMX channels
- Control protocol: DMX512, WDMX, remote control
- Housing color: black
- Without fan
- Color temperature: 3000K~7600K
- Rugged and water resistant housing
- XLR connectors: 3-pin Seetronic connectors
- Power con True1 current input
- Protection class: IP65
- Operating modes: Auto, DMX, Master/Slave, WDMX, IR remote control
- Power input: 100 ~ 240 V, 50/60 Hz
- Battery: Lithium-Ion 11.1V / 14400 mAH
- Autonomy: from 3 to 15h (mono-color)
- Charging time : from 3 to 4h
- Dimensions : 220 x 215 x 265 mm
- Net weight : 5.5 kg
Installation
Rigging
The installation of the projector has to be built and constructed in a way
that it can hold 10 times the weight for 1 hour without any harming
deformation.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including
calculating working load limits, installation material being used, and
periodic safety inspection of all installation material and the projector. If
you lack these qualifications, do not attempt the installation yourself, but
instead use a professional structural rigger. Improper installation can result
in bodily injury and or damage to property. The projector had to be installed
out of the reach of people
Always secure your fixture with a safety cable!
DMX 512 Connection
The wires must not come into contact with each other, otherwise the fixture
will not work at all or properly. Please note the starting address depends
upon which controller is being used. Only use a DMX cable and 3-pin XLR-plugs
and connectors in order to connect the controller with the fixture or one
fixture to another.
Connection with the mains
The occupation of the connection-cables is as follows:
| Cable | Pin | International |
|---|---|---|
| Brown | Live | L |
| Blue | Neutral | N |
| Yellow/Green | Earth |
The earth has to be connected. The device must only be connected with an electric installation carried out in compliance with IEC standards.
Set up
Control panel
The control board offer several features: you can simple set the starting
address, run the preprogrammed program or make a reset. The main menu is
accessed by pressing the Menu button, Browse through the submenu by pressing
Up or Down. Press the Enter-button in order to select the desired menu. You
can change the selection by pressing Up or Down, confirm every selection by
pressing the Enter-button. The functions provided are described in the
following setting.
| Button | Function |
|---|---|
| < MENU> | Scrolls through the first level of options, or exits from the |
current menu or
function
< UP>| Navigates upward through the menu list or increases the numeric
value
when in a function
< DOWN>| Navigates downward through the menu list or decreases the
numeric value
when in a function
< ENTER>| Enables the currently displayed menu or sets the currently
selected value in to the current function
| MODE | FUNCTION |
|---|---|
| A001 （A001—A512） | ADDRESS CODE |
CHND
(6CH/8CH/10CH）| CHANNEL MODE
CL01 （CL01—CL32）| 32 Mixing color mode
CC01 （CC01—CC99）| Change color mode，ENTER key adjust speed SP01-99
EE01 （EE01—EE99）| jump color change mode，ENTER key adjust speed SP01-99
FF01 （FF01—FF99）| fade color change mode，ENTER key adjust speed SP01-99
ST01 （ST01—ST32）| strobe，ENTER key adjust speed SP01-99
SOU1 (SOU1/2/3/4)| Sound mode: SOU1 fade SOU2 jump color change SOU3
strobe
SOU4 fade+jump change+strobe (ENTER key adjust sensitivitySE01-99)
NANU| R manual dimmer 0-255
G manual dimmer 0-255
B manual dimmer 0-255
W manual dimmer 0-255
Y manual dimmer 0-255
P manual dimmer 0-255
NDIN (CUR1/2/3/4)| 4 Dimming curve（Square, straight, logarithmic,
S-shaped） Press the “ENTER” key to adjust the curve delay on / off
2.4G (ON/OFF)| WIRELESS 2.4G ON/OFF
IRCL(ON/OFF)| REMOTE ON/OFF
POUR(ON/OFF)| KEY switch ON/OFF
LED(ON/OFF)| DISPLAY ON/OFF
T000(OFF/40-100)| Temperature display and power reduction temperature
setting
DMX – WDMX modes
Each fixture can be controlled individually with a standard DMX-512
controller.
Each fixture must be “addressed” using the “A001” menu. The address entered is
the base address, the address from which the fixture will respond.
If two fixtures are addressed to the same DMX address, they will behave
identically, responding to the same DMX channels.
This product also has wireless DMX technology. It is compatible with the
Evolite DWT-512 and Wireless Solution up to G4 protocol. Attention, not
compatible with G5 protocol.
The WI-PAR 12X12W also supports wireless master/slave transmission as the
product is equipped with a wireless transmitter/receiver.
To make a wireless connection
- Turn on the transmitter (not supplied).
- Turn on the WI-PAR 12X12W
- Navigate in the menu and activate the 2.4G > ON. Do this on each product.
- The receiver will then connect to the transmitter
Mode DMX 10 Canaux
| Channel | Value | Function |
|---|---|---|
| 1 | 000 – 255 | Master Dimmer 0-100% |
| 2 | 000 – 255 | Red 0-100% |
| 3 | 000 – 255 | Green 0-100% |
| 4 | 000 – 255 | Blue 0-100% |
| 5 | 000 – 255 | White 0-100% |
| 6 | 000 – 255 | Amber 0-100% |
| 7 | 000 – 255 | UV 0-100% |
| 8 | 000 – 255 | Strobe, from slow to fast |
| 9 | 000 – 255 | 0-9close |
10-50select color，10CH select 32kinds static color
51-100colro change，10CHadjust speed, 101-150color fade，10CHadjust speed,
151-200color jump，10CHadjust speed
201-220color change sound control 221-240jump change sound
241-255strobe sound control
10| 000 – 255| Speed 0-100% from slow to fast
Mode DMX 8 Canaux
| Channel | Value | Function |
|---|---|---|
| 1 | 000 – 255 | Master Dimmer 0-100% |
| 2 | 000 – 255 | Strobe, from slow to fast |
| 3 | 000 – 255 | Red 0-100% |
| 4 | 000 – 255 | Green 0-100% |
| 5 | 000 – 255 | Blue 0-100% |
| 6 | 000 – 255 | White 0-100% |
| 7 | 000 – 255 | Amber 0-100% |
| 8 | 000 – 255 | UV 0-100% |
Mode DMX 6 Canaux
| Channel | Value | Function |
|---|---|---|
| 1 | 000 – 255 | Red 0-100% |
| 2 | 000 – 255 | Green 0-100% |
| 3 | 000 – 255 | Blue 0-100% |
| 4 | 000 – 255 | White 0-100% |
| 5 | 000 – 255 | Amber 0-100% |
| 6 | 000 – 255 | UV 0-100% |
Note. If 2 fixtures are addressed with same DMX value, they will move
exactly the same way.
Remote
Maintenance & Service
Cleaning
The cleaning of internal must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics.
- Clean with soft cloth using normal glass cleaning fluid.
- Always dry the parts carefully.
- Clean the external optics at least every 20 days.
Troubleshooting
Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting:
- The fixture does not work, no light
- Check the connection of power and main fuse.
- Measure the mains voltage on the main connector.
- Not responding to DMX controller
- DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
- If the DMX LED is on and no response to the channel, check the address settings and DMX polarity.
- If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the fixture or the previous one.
- Try to use another DMX controller.
- Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit.
- Some fixtures don’t respond to the easy controller
- You may have a break in the DMX cabling.
- Check the LED for the response of the master/ slave mode signal.
- No response to the sound
- Make sure the fixture does not receive DMX signal.
- Check microphone to see if it is good by tapping the microphone.
Customer Support
Imported by
EVOLITE – MSC
7 avenue du 1er Mai
91120 Palaiseau / FRANCE
infos@msc-distribution.com
Tel : +33 1 69 34 80 62
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>