gofanco DP14MST2HD DisplayPort 1.4 MST 2 Port HDMI Hub User Guide
- June 3, 2024
- gofanco
Table of Contents
gofanco DP14MST2HD DisplayPort 1.4 MST 2 Port HDMI Hub
Thank you for purchasing from gofanco. Our products aim to meet all your connectivity needs wherever you go. For optimum performance and safety, please read the instructions carefully and keep this User’s Guide for future reference. If you need more information about our products, please visit www.gofanco.com. For technical support, please email us at [email protected]. For drivers/manuals download, please go to www.gofanco.com/ downloads.
Important Safety Notices
Please read safety instructions carefully before installation and operation.
- Please pay close attention to all warnings and hints for this device
- Do not expose this unit to rain, heavy moisture, or liquid
- Do not repair the device or open the enclosure without professional guidance to avoid electric shocks. Doing so may void your warranty
- Keep the product in a well-ventilated location to avoid damage from overheating
Introduction
gofanco DisplayPort 1.4 MST 2-Port HDMI Hub enables you to connect with 2 external monitors to your DisplayPort enabled computer.
Package Contents
- DisplayPort 1.4 MST 2-Port HDMI Hub
- Micro-USB Power Cable
- User’s Guide
System Requirements
-
PC with an available DisplayPort output (DP 1.4 recommended)
-
Windows® 11 /10 / 8.1 / 8 / 7 (32-/64-bit)
Important Notes: -
DisplayPort 1.4 GPU output is required to support two displays up to 4K @60Hz
-
DisplayPort 1.2 GPU output only supports two displays up to 4K @30Hz
-
macOS does NOT support MST function and will only mirror the displays · Most Intel GPU’s (video cards) are limited to 3 external displays altogether, including the displays connected to the MST hub
Product Layout
- DP IN: Connect to PC’s DisplayPort
- HDMI Output (x2): Connect to HDMI displays with HDMI cables (not included)
- Power Jack (Micro-USB): Connect to a USB 3.0 port or 5V/1A to 5V/2A wall charger for power with the included Micro-USB power cable.*Note: This connection is required to power this adapter.
Hardware Installation
Important: If the source DP output doesn’t support DP 1.2/1.4, the Multi Stream Transport function will be disabled and this hub becomes a Splitter, mirroring your video source across all displays.
- Power off all devices you plan to connect to the unit.
- Connect the unit to your PC’s DisplayPort connector.
- Connect your HDMI monitors to the unit’s HDMI Outputs with HDMI cables (not included).
- Connect the unit’s Power Jack to a USB 3.0 port or 5V/1A to 5V/2A wall charger for power with the included Micro-USB power cable. Note: This connection is required to power the adapter.
- Power on all of the connected devices.
- The MST hub is ready for use.
Connection Diagram
Specifications
Hardware
Output Signal| HDMI
Output Ports| 2HDMI
Audio Output| LPCM 7.1
Compliance| DP 1.4
HDMI compliant
Connectors| Input: lx Displa yPo rt, Male Output: 2x HDMI, Female
Power Jack: Micro USB, Female, 5V/900mA to 5V /2A
Cable Length| 6 inches (150mm)
Video Resolution
Windows (MST mode)
| DP 1.4: Up to 3840×2160 @60Hz (single or dual displays)
DP 1.2: Up to 3840×2160 @60Hz (single display); 3840×2160 @30Hz (dual
displays)
Environmental Conditions
Operating Temperature| 32 to 158 F (0 to 70 C)
Storage Temperature| 14 to 131 F (-10 to 55 C)
Humidity| 0% to 85% RH (no condensation)
Disclaimer
The product name and brand name may be registered trademarks of related
manufacturers. TM and ® may be omitted on the user’s guide. The pictures on
the user’s guide are just for reference, and there may be some slight
differences with the actual products.
We reserve the right to make changes without prior notice to a product or
system described herein to improve reliability, function, or design.
Thank you for choosing gofanco
www.gofanco.com
