BAFANG DP C010.CB Display LCD User Manual

June 9, 2024
BAFANG

BAFANG - logo DP C010.CB Display LCD
User Manual
BAFANG DP C010.CB Display LCD

IMPORTANT NOTICE

  • If the error information from the display cannot be corrected according to the instructions, please contact your retailer.
  • The product is designed to be waterproof. It is highly recommended to avoid submerging the display under water.
  • Do not clean the display with a steam jet, high-pressure cleaner or water hose.
  • Please use this product with care.
  • Do not use thinners or other solvents to clean the display. Such substances can damage the surfaces.
  •  Warranty is not included due to wear and normal use and aging.

INTRODUCTION OF DISPLAY

  • Model: DP C010.CB
  • The housing is made of PC+ABS; the LCD display windows is made of tempered glass; the button is made of ABS:

BAFANG DP C010.CB Display LCD - LCD display

  • The label marking is as follows:

DPC010CBF80101.0 PD051505BAFANG DP C010.CB Display LCD - qr
code

Note: Please keep the QR code label attached to the display cable. The information from the Label is used for a later possible software update.

PRODUCT DESCRIPTION

7.3.1 Specification

  • 4.0“, 480*800 (RGB) TFT screen
  • Power supply: 36/43/48/50.4/60/72Vdc
  • Operating temperature: -20℃~45℃
  • Storage temperature: -20℃~60℃
  • Waterproof: IP66
  • Storage Humidity: 30%-70% RH

7.3.2 Functional Overview

  • Battery capacity indication
  • Power-assisted mode selection
  • Speed indication (including the max. speed and average speed)
  • Unit switching between km and mile
  • Motor power indication
  • Mileage indication (including single-trip distance TRIP, total distance ODO, and remaining distance Range)
  •  Walk assistance
  • Automatic sensors explanation of the lighting system
  • Brightness setting for backlight
  • Intelligent indication (including energy consumption CAL and Cadence, only when the matching controller supports this function)
  • Information of controller, HMI and battery
  • Error code and warn code indiaction
  • Bluetooth Function
  • USB charge (max. charge current: 1A)
  • Service indication
  •  Clock indication
  • 3 Themes (Sporty, Fashion, Technology)
  • 6 Languages (English, German, Dutch, French, Italian, Czech)

DISPLAY

BAFANG DP C010.CB Display LCD - DISPLAY

  1. Battery capacity indication
  2. Warn code indication
  3. Speed in real-time
  4. Speed bar
  5. Power-assisted mode indication (4 Modes/
  6. Modes)
  7. Unit switching of speed (km/h, mph)
  8. Multifunction indication (Clock. TRIP, ODO, MAX, AVG, Range, CAL, Cadence, Time)
  9. Symbol indication (Headlight, USB, Service, Bluetooth)

KEY DEFINITION

BAFANG DP C010.CB Display LCD - KEY DEFINITION

NORMAL OPERATION

7.6.1 Power ON/OFF
Press and hold (>2S) to power on the HMI, and the HMI displays the boot up LOGO.
Press and hold (>2S) again to power off the HMI. 7.6.2 Power-Assisted Mode Selection
When HMI powers on, briefly press or (<0.5S) to select the power-assisted mode and change the output power of motor. 4 Modes or 6 Modes can be selected, but the default selection is 6 Modes of which the lowest mode is ECO and the highest mode is BOOST. The default mode is ECO after HMI powering on, mode OFF means no power assistance. BAFANG DP C010.CB Display LCD - Mode
Selection7.6.3 Headlight / Backlight
The headlight can be switched on manually or automatically. When the HMI powers on, the auto light function works. Press and hold (>2S) to turn on the headlight and reduce the brightness of backlight. Press and hold (>2S) again to turn off the headlight and increase the brightness of backlight.
(Note: The headlight can be automatically switched according to the ambient light, but the auto light function fails once user manually switches the headlight on/off. After restarting the HMI, the function works again.) 7.6.4 Walk Assistance
Note: The walk assistance can only be activated with a standing e-bike.
Briefly press button (<0.5S) until this symbol appears. Next keep pressing the button until the walk assistance is activated and the symbol is flashing. (When the real-time speed is less than 2.5km/h, the speed indication is shown as 2.5km/h.) Once releasing the button, it will exit the walk assistance and the symbol stops flashing. If no operation within 5s, the HMI will automatically return to mode OFF. 7.6.5 Multifunction Selection
Briefly press button (<0.5S) to switch the different function and information. The position of multifunction indication displays the real-time clock (Clock) → single trip distance (TRIP, km) → total distance (ODO, km) → maximum speed (MAX, km/h) → average speed (AVG, km/h) → remaining distance (Range, km) → energy consumption (CAL, kcal) → riding cadence (Cadence, rpm) → riding time (Time, min) → cycle.BAFANG DP C010.CB Display LCD - Multifunction
Selection

7.6.6 Battery Capacity Indication
HMI displays the real-time battery capacity from 100% to 0%. When the battery capacity is less than 5%, the indicator will blinks at frequency of 1 Hz to alert to recharge. 7.6.7 Bluetooth Function
This HMI is equipped with OTA function, which can update the firmware of HMI, controller, sensor and battery through the Bluetooth.
This HMI can be connected to the Bafana Go+ APP through Bluetooth.

BAFANG DP C010.CB Display LCD - qr code 1https://link.e7wei.cn/?gid=127829https://link.e7wei.cn/?gid=127842

(BAFANG GO+ for Android and iota ) The data that can be sent to the APP are as follows:

1 Function
2 Speed
3 Power-assisted mode
4 Battery capacity
5 Headlight state
6 TRIP
7 ODO
8 Range
9 Heartbeat (customized)
10 Calories
11 Sensor signal
12 Battery info.
13 System info.
14 Error code

BAFANG DP C010.CB Display LCD - Headlight 1 7.6.8 USB Charge Function
When the HMI is off, insert the USB cable to the charge port on the HMI, and then turn on the HMI to start charging. The maximum charge voltage is 5V and the maximum charge current is 1A.BAFANG DP C010.CB Display LCD - Headlight
1 7.6.9 Service Tip
When the total mileage exceeds 5000 km, the symbol will be displayed on the HMI, reminding users to go to the after-sales outlet for maintenance. The function is off by default. 7.6.10 Riding Data Interface
Double press the button (<0.5S) to enter the interface of riding data. Press the  button (<0.5S) to switch the pages. Dabble press the button (<0.5S) again to return the main interface.
When the real-time speed is less than 5 km/h and the power assisted mode is not walk assistance, press and hold the button (>2S) to clear the riding data of Trip, MAX, AVG, Time.BAFANG DP C010.CB Display LCD - Riding
Data

SETTINGS

7.7.1 “Quick settings” Interface
When you in the main interface, press and hold the and button (at the same time) to enter the “Quick settings” interface.
When you in the “Quick settings” interface, press and hold the and button (at the same time) to exit back to the main interface.
7.7.1.1 “Brightness” Set the brightness of backlight
Briefly press the or button (<0.5S) to select “Brightness”, and briefly press the to enter the item. Then select the desired percentage from 10% to 100% by pressing the or button, and briefly press the button (<0.5S) to save and exit back to the “Quick settings” interface.BAFANG DP C010.CB Display LCD -
Brightness 7.7.1.2 “Auto off” Set automatic off time
Briefly press the or button (<0.5S) to select “Auto off”, and briefly press the  to enter the item. Then select the automatic off time as “OFF”/“1”/“2”/“3”/“4”/“5”/“6”/“ 7”/“8”/“9” with the or button. Once you have chosen your desired selection, press the button (<0.5S) to save and exit back to the “Quick settings” interface.
Note: “OFF” means the “Auto off” function is off.BAFANG DP C010.CB
Display LCD - Brightness 1 7.7.1.3 “Clock setting” Set the clock
Briefly press the or button (<0.5S) to enter the “Time format” setting, and briefly press the button to select “12h” or “24h”.
Briefly press the or button (<0.5S) to select the “Clock setting“ item, briefly press the button to enter the item. Then set the accurate time by pressing the or button, and briefly press the button (<0.5S) to save and exit back to the “Quick settings” interface.BAFANG DP C010.CB Display LCD - Clock
setting 7.7.1.4 “Theme” Set the theme
Briefly press the or button (<0.5S) to select the desired “Theme”, and briefly press the button to save the selection.BAFANG DP C010.CB Display LCD - Clock
setting 1 7.7.1.5 “Modes” Set the power-assisted modes
Briefly press the or button (<0.5S) to enter the “Modes” setting, and briefly press the button to select “4 Modes” or “6 Modes”. 7.7.1.6 “Trip reset” Reset the single-trip
Briefly press the or button (<0.5S) to enter the “Trip reset” setting, and briefly press the button to select “YES” or “NO”. 7.7.2 “Display settings” Interface
When you in the “Quick settings” interface, briefly press the or button (<0.5S) to select the “OTHERS” and enter the
“Display settings” interface.
7.7.2.1 “Trip reset” Reset the single-trip
Briefly press the or button (<0.5S) to select the “Trip reset” item, and briefly press the button to enter the item. Then select “YES”/“NO” (“YES”- to clear, “NO”-no operation) with the or button and briefly press the button (<0.5S) to save and exit back to the “Display settings” interface.
Note: The riding time (Time), average speed (AVG) and maximum speed (MAX) will be reset simultaneously when you reset TRIP. 7.7.2.2 “Unit” Select the mileage unit
Briefly press the or button (<0.5S) to select the “Unit” item, and briefly press the button to enter the item. Then select “km”/“mile” with the or button and briefly press the button (<0.5S) to save and exit back to the “Display settings” interface.BAFANG DP C010.CB Display LCD - Display
setting 7.7.2.3 “Service tip” Set the service tip
Briefly press the or button (<0.5S) to select the “Service tip” item, and briefly press the button to enter the item. Then select “ON”/“OFF” with the or button and briefly press the button (<0.5S) to save and exit back to the “Display settings” interface.
Note: The default setting is OFF. If the ODO is more than 5000 km, the “Service tip” indication will flash. 7.7.2.4 “AL Sensitivity” Set light sensitivity
Briefly press the or button (<0.5S) to select the “AL sensitivity” item, and briefly press the button to enter the item. Then select the level of the light sensitivity as “OFF”/“1”/ “2”/“3”/“4”/“5” with the or button and briefly press the button (<0.5S) to save and exit back to the “Display settings” interface.
Note: “OFF” means the light sensor is off. Level 1 is the weakest sensitivity and level 5 is the strongest sensitivity. 7.7.2.5 “Boot Password” Set the boot password
Briefly press the or button (<0.5S) to select the “Boot Password” item, and briefly press the button to enter the item. Then select the 4-digit number as “0”/ “1”/“2”/“3”/“4”/“5”/“6”/“7”/“8”/“9”with the or button. After setting, select the “YES” by briefly pressing the button (<0.5S) to save and exit back to the “Display settings” interface.
After back to the “Display settings” interface, briefly select “ON”/“OFF” with the or button and briefly press the button (<0.5S) to save and exit back to the “Display settings” interface.
Note: The default password is 0000, and the default setting is OFF.BAFANG DP C010.CB Display LCD - Boot Password 7.7.2.6 “Reset Password” Reset the boot password
Briefly press the or button (<0.5S) to select the “Reset Password” item, and briefly press the button to enter the item. Enter the 4-digit old password with the or   button, then enter the new password and confirm the new password. After setting, select the “YES” by briefly pressing the button (<0.5S) to save and exit back to the “Display settings” interface.BAFANG DP
C010.CB Display LCD - Information 7.7.3 “Information” Interface
Note: All information here cannot be changed, it is to be viewed only.
7.7.3.1 “Wheel size”
After entering the “Information” page, you can see “Wheel size –inch” directly.
7.7.3.2 “Speed limit”
After entering the “Information” page, you can see “Speed limit –km/h” directly.

7.7.3.3 “Battery info”
Briefly press the or button (<0.5S) to select “Battery info”, and briefly press the button to enter, then briefly press the or button to view the battery information.
Note: If the battery doesn’t have communication function, you won’t see any data from battery.BAFANG DP C010.CB Display LCD -
battery 7.7.3.4 “Controller info”
Briefly press the or button (<0.5S) to select ”Controller info”, and briefly press the button to view the hardware version and software version.
Press the button (<0.5S) again to exit back to the “Information” interface. 7.7.3.5 “HMI info”
Briefly press the or button (<0.5S) to select ”HMI info”, and briefly press the button to view the hardware version and software version.
Press the button (<0.5S) again to exit back to the “Information” interface. 7.7.3.6 “Sensor info”
Briefly press the or button (<0.5S) to select ”Sensor info”, and briefly press the button to view the hardware version and software version.
Press the button (<0.5S) again to exit back to the “Information” interface.
NOTE: If your e-bike doesn’t have torque sensor, “–” will be displayed.BAFANG DP C010.CB Display LCD - Sensor info 7.7.3.7 “Warn code”
Briefly press the or button (<0.5S) to select ”Warn code”, and briefly press the button to view the message of warn code.
Press the button (<0.5S) again to exit back to the “Information” interface.BAFANG DP C010.CB Display LCD - Warn code 7.7.3.8 “Error code”
Briefly press the or button (<0.5S) to select ”Error code”, and briefly press the button to view the message of error code.
Press the button (<0.5S) again to exit back to the “Information” interface.BAFANG DP C010.CB Display LCD - Error code 7.7.4 “Language” Interface
When you in the “Language” interface, briefly press the or button (<0.5S) to select the desired language as “English”/”Deutsch”/”Nederland’s”/”François”/”Italian”/”Sestina” and briefly press the button to save the selection.

7.7.5 “Theme” Interface
When you in the “Theme” interface, briefly press the or button (<0.5S) to select the desired theme as “Sporty”/”Technology”/”Fashion” and briefly press the button to save the selection.BAFANG DP C010.CB Display LCD -
Theme

ERROR CODE DEFINITION

The ebike system’s parts are automatically monitored in real time. If a part is abnormal, the corresponding error code is displayed on the HMI. The DP C010.CB displays the error code on the HMI directly.

The troubleshooting methods in the list are listed in order according to the fault probability and the operability of the related parts. In practice, dealers can adjust the order  based on the existing tools and spare parts. (For detailed disassembly steps, please refer to the dealer manual of the corresponding parts on the official website. <www.bafang-e.com>)

In order to protect the electric parts, before disassembling the parts, please switch off the system power first by pressing the control unit of HMI and then disconnect the  power cable of the disassembled part. When installing the parts, please fix the parts first, then connect the power cable of the parts, and finnally switch on the system power  by pressing the control unit of HMI.

Please contact Bafang after-sale service personnel <service@bafang-e.com> if the above troubleshooting fails to solve the problem or the error code is not in the above list.

Code Cause Troubleshooting
Hub Motor System Mid Motor System
5 Throttle not in place 1. Check whether the throttle is in place.

2. Check whether the throttle cable is connected correctly or the cable (from throttle to controller) is damaged.
3. Troubleshoot the faulty part:

  1. Replace the throttle

  2. Replace the controller| 1. Check whether the throttle is in place.
    2. Check whether the throttle cable is
    connected correctly or the cable (from
    throttle to drive unit) is damaged.
    3. Troubleshoot the faulty part:

  3. Replace the throttle

  4. Replace the drive unit
    7| System overvoltage protection| 1. Check whether the nominal voltage
    of the battery is the same as the controller.
    2. Troubleshoot the faulty part:

  5. Replace the battery

  6. Replace the controller| 1. Check whether the nominal voltage of the battery is the same as the  drive unit.
    2. Troubleshoot the faulty part:

  7. Replace the battery

  8. Replace the drive unit
    8| Hall signal in motor is
    abnormal| 1. Check whether the motor cable is
    connected correctly or the cable (from
    motor to controller) is damaged.
    2. Troubleshoot the faulty part:

  9. Replace the motor

  10. Replace the controller| Replace the drive unit
    9| Phase wire in motor abnormal| 1. Check whether the motor cable is
    connected correctly or the cable (from
    motor to controller) is damaged.
    2. Troubleshoot the faulty part:

  11. Replace the motor

  12. Replace the controller| Replace the drive unit
    10| Motor overtemperature
    protection
    (Only occur when the
    motor is equipped with the
    temperature sensor.)| 1. If riding for a long time, turn off the
    system and let the motor cool down.
    2. If no ride or riding for a short time,
    troubleshoot the faulty part:

  13. Replace the motor

  14. Replace the controller| 1. If riding for a long time, turn off the system and let the drive unit cool down.
    2. If no ride or riding for a short
    time, replace the drive unit.
    11| Motor temperature sensor abnormal (Only occur when the motor is equipped with  the temperature sensor.)| 1. Check whether the motor cable is connected correctly or the cable (from motor  to controller) is damaged.
    2. Troubleshoot the faulty part:

  15. Replace the motor

  16. Replace the controller| Replace the drive unit
    12| Controller curent sensor abnormal| Replace the controller| Replace the drive unit
    14| Controller overtemperature protection| 1. If riding for a long time, turn off
    the system and let the controller cool
    down.
    2. If no ride or riding for a short time,
    replace the controller.| 1. If riding for a long time, turn off
    the system and let the drive unit cool
    down.
    2. If no ride or riding for a short time,
    replace the drive unit.
    15| Controller temperature sensor abnormal| Replace the controller| Replace the drive unit
    21| Speed sensor abnormal| 1. Check whether the motor cable is connected correctly or the cable (from motor  to controller) is damaged.
    2. Troubleshoot the faulty part:

  17. Replace the motor

  18. Replace the controller| 1. Check whether the spoke magnet
    has fallen off or the clearance
    between the spoke magnet and the speed sensor is within the normal range (10-15mm).
    2. Check whether the speed sensor cable is connected correctly or the cable (from sensor to drive unit) is damaged.
    3. Troubleshoot the faulty part:

  19. Replace the speed sensor

  20. Replace the drive unit
    26| Torque sensor abnormal (Only occur  when the drive system is equipped with the torque sensor.)| 1. Check whether the torque sensor cable is connected correctly or the cable (from sensor to controller) is damaged.
    2. Troubleshoot the faulty part:

  21. Replace the torque sensor

  22. Replace the controller| Replace the drive unit
    30| Communication abnormal| 1. Check whether the HMI cable is
    connected correctly or the cable (from
    HMI to controller) is damaged.
    2. Troubleshoot the faulty part:

  23. Replace the controller if the HMI
    turns off automatically after appearing
    error code for 20 seconds.

  24. Replace the HMI if the HMI doesn’t  turn off automatically after appearing error  code for 20 seconds.

  25. If the BESST tool is available, connect it with HMI and controller, read the  information of HMI and controller and replace the part that cannot read information.

| 1. Check whether the HMI cable is connected correctly or the cable (from HMI to drive unit) is damaged.
2. Troubleshoot the faulty part:

  1. Replace the drive unit if the HMI turns off automatically after appearing error code for 20 seconds.

  2. Replace the HMI if the HMI  doesn’t turn off automatically after appearing error  code for 20 seconds.

  3. If the BESST tool is available, connect it  with HMI and drive unit, read the  nformation of HMI and drive unit and  replace the part that cannot read information.

36| ON/OFF Button detection circuit  abnormal (Only occur when the drive system is equipped with Bafang CAN  communication protocol.)| 1. If keep pressing the ON/OFF button when the HMI powers on, the error code  will alarm. Release the button and observe  whether the code disappears.
2. Troubleshoot the faulty part:

  1. Replace the HMI
  2. Replace the controller| 1. If keep pressing the ON/OFF button  when the HMI powers on, the error code will  alarm. Release the button and observe whether the code disappears.
    2. Troubleshoot the faulty part:
  3. Replace the HMI
  4. Replace the drive unit
    37| WDT (Watch Dog Timer) in
    controller is abnormal| Replace the controller| Replace the drive unit
    42| Discharge voltage of battery pack is too low| 1. Charge the battery
    2. Replace the battery|
    49| Discharge voltage of single cell is too low| 1. Charge the battery
    2. Replace the battery|
    4C| Voltage difference between single cell| Replace the battery|

The battery error codes of 42, 49, 4C only occur when the drive system is equipped with the smart BMS and Bafang CAN communication protocol.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals