Dongguan SLEEP BOX3 Bone Conduction Wireless Music Box Wireless Portable User Manual
- August 31, 2024
- Dongguan
Table of Contents
Dongguan SLEEP BOX3 Bone Conduction Wireless Music Box Wireless Portable
FAQs
Q: How do I switch between different modes on the device?
A: To switch between Bluetooth mode, TF card mode, and built-in white noise mode, double-click the power button.
Q: Can I use any 5V charging head with the Type-C charging cable?
A: Yes, you can use any 5V charging head with the Type-C charging cable for charging the device.
Function and accessory
- TF Card
- Volume “+”
- Volume “_”
- 4 Power on/Off
- Type-C charging
- LED digital tube display
Accessory list
- Device 1 pcs
- Type-C charging cable 1pcs
- User manual 1pcs
Instructions
Power on/off
Long press the power button for 3 seconds. When the indicator light flashes red and blue alternately, the product is powered on. After 30 minutes of disconnected Bluetooth connection, it will automatically shut down or long- press the power button for 3 seconds
Bluetooth connect
When the product is used for the first time, it will enter the Bluetooth pairing mode after the product is turned on. At this time, SLEEP BOX 3 can be found in the Bluetooth Settings of the phone. The connection is successful and the blue light of the playback status indicator flashes slowly
Power off
Press power on/off and keep 3 seconds it will be turned off
Charging
Simply insert the Type-C charging cable and any 5V charging head for charging. During the charging process, the battery level will increase and the full charge level will remain constant.
On/Off key
- Long press “power on/off “
- Short press once to “pause”
- Double-click to switch between Bluetooth mode
- TF card mode, and built-in white noise mode
Previous and next song
Click once “+” button volume up, and keep pressing the Volume “+” button second to the next song; Click once “-” button volume down, keep pressing Volume “-” to the previous song
Timing on/off
click the Power button three times to Turn on/off the Timing version, it will turn off after 60 Minutes by itself
Specification
- Model number: SLEEP BOX 3
- Bluetooth Version:5.4
- N.W:50g
- Battery:300mAh
- charging time:2 hours
- playing time:8 Hours
- Bluetooth Distance:10M
- Input:5V/200mA
- Agreement: A2DP, AVRCP, HSP, HFP
- Unit size:15.5CM3.6Cm1.2CM
Faults and eliminate
Can not power on
Check if the battery is without power, Keep Press power on button for 3 seconds
Bluetooth unconnect
Whether the product is in pairing state? If the product indicator is blinking blue at a slow time, it indicates that the product is connected to other devices. Please disconnect the currently connected devices
Large sound leakage
In sleep mode, please adjust the volume of the mobile phone to within %, which can not be heard by the person next to the pillow. The volume above 50% is in entertainment mode
Bluetooth range
Please confirm whether the phone is connected to Bluetooth version 4.0 or later. Earlier versions may cause short Bluetooth range
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may causeundesired operation. Any Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Thank you for your purchase and support