MURPHY DOOR 2024 Signature Floating Shelf Instructions
- August 30, 2024
- MURPHY DOOR
Table of Contents
2024 Signature Floating Shelf
Specifications:
- Product Name: Signature Floating Shelf
- Manufacturer: murphydoor.com
- Contact: 888.458.5911
Product Usage Instructions:
1. Wall Plate Installation
-
Determine the location for the shelf on a suitable wall with
2×4 or 2×6 construction. -
Locate and mark the studs using a stud finder.
-
Attach the wall plate to a stud using screws, leaving it loose
enough to rotate. -
If using wall anchors, level the wall plate, mark the holes,
drill, and insert anchors. -
Secure the wall plate with lag screws at stud locations and
screws at wall anchors. -
Tighten all screws securely.
2. Shelf Assembly
-
Thread the shelf arms into the slides.
-
Slide the arms onto the wall plate.
-
Align the arms with the holes in the back of the shelf and
slide it against the wall. -
Adjust the shelf position as desired.
-
Pull the shelf back slightly from the wall.
-
Use an adjustable wrench to tighten the flat sections at the
base of each arm into the slide to lock them in place. -
Slide the shelf back against the wall to complete
installation.
FAQ:
Q: What should I do if I can’t locate studs for mounting?
A: If studs are not available, use appropriate wall anchors for
secure mounting following the provided instructions.
Q: Can I adjust the height of the shelf after
installation?
A: Yes, you can adjust the height by loosening the screws and
repositioning the shelf accordingly.
Signature Floating Shelf
murphydoor.com I 888.458.5911
PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY
Tools Needed · Safety glasses · Measuring tape · Pencil or something to mark the wall · Stud finder · Level · Drill · Phillips head driver bit · 1/8″ drill bit · Philips head screwdriver · Adjustable (Crescent) Wrench
Wall Plate
Shelf Arm 18″ Hardware x2 34″ and 52″ Hardware x4
Shelf Slide 18″ Hardware x2 34″ and 52″ Hardware x4
3″ Lag Screw 18″ Hardware x4 34″ Hardware x6 52″ Hardware x8
Wall Anchor All Hardware x4
8 x 1″ Screw All Hardware x4
1
Determine where you want to place your shelf. Make sure the wall is suitable
for hanging the shelf. The wall should have either 2×4 or 2×6 construction.
You will need to secure the hardware to at least 1 wood stud, more are
preferred. Determine the height you want the top of your shelf, and measure
down 3/8″. This will mark the top of the wall plate for the mounting hardware.
2
Using a stud finder locate and mark the studs. *If you are mounting to a
single stud or the ends of the wall plate are more than 2″ (2 mounting holes)
away from the nearest stud, the ends of the wall plate will need to be secured
with wall anchors.
888.458.5911
murphydoor.com
PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY
3
Using a drill, with a Phillips head driver, attach the wall plate using one of
the 3″ screws into one of the studs just tight enough that the wall plate can
still be rotated by hand.
4
FOR WALL ANCHORS ONLY Level the wall plate and mark the wall at the
mounting holes at each end of the hardware. Use a 1/8″ drill bit and drill all
marked locations.
5
The wall anchors provided are self-drilling. Align the drilling point of the
anchor with the pilot hole and use a Phillips head screwdriver to drive the
anchor into the wall until it stops.
6
Level the wall plate and finish securing the shelf to the wall using
additional 3″ lag screws at each stud location and 1″ screws at each wall
anchor.
7
Make sure all screws are fully tightened.
888.458.5911
8
Thread the shelf arms into the slides.
murphydoor.com
PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY
9
Slide them onto the wall plate.
10
Align the arms with the holes in the back of your shelf and slide the shelf
all the way against the wall.
11
Adjust the shelf side to side until it is where you want it.
12
Pull the shelf back out from the wall 2-3″.
13
Locate the two flat sections near the base of each arm and use an adjustable
wrench to turn them clockwise to tighten them into the slide and lock the arm
in place.
14
After doing this at each arm, slide the shelf back against the wall.
Congratulations. You have successfully installed your Signature Floating
Shelf.
888.458.5911
murphydoor.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>