2024 Murphy Shelf with Secret Drop Down Compartment

Product Information

Specifications:

• Product Name: Murphy Shelf with Secret Drop Down
  Compartment

• Manufacturer: murphydoor.com

• Contact: 888.458.5911

• Components: Lock Body, Strike, USB Power Extension Cable, USB
  Power Adapter, RFID Cards x3, Power Jack Screw x4, Strike Screws
  x2, Wall Plate

• Power Source: 4 AAA Batteries (not included)

Product Usage Instructions

1. Gas Strut Installation:

Using a mini flathead screwdriver, gently pry up on the metal
clip holding the gas strut to the mounting bracket and separate
them.

2. Lock and Strike Installation:

Your Murphy Shelf ships with the lock and strike uninstalled.
Insert 4 AAA batteries into the lock, program the manager and user
cards, and set up the Bluetooth connected app as per the
programming instructions at the end of the document.

3. Lock Installation:

After inserting batteries, use a screwdriver to install the lock
to the pre-marked location in the drop-down shelf with the latch
openings towards the front.

4. Power Jack Installation:

Install the power jack cable through the hole at the back of the
drop-down shelf. Plug the backup power jack into the side of the
lock.

5. Power Extension Cable Test:

Test the power jack in the bottom of the shelf using the
included power extension cable. Adjust the depth of the power jack
through mounting bracket if needed.

6. Front and Top Panel Installation:

The front and top panels are pre-drilled for installation.
Attach the strike to the front panel and align with screw holes.
Ensure push pins retract smoothly.

Frequently Asked Questions (FAQ)

Q: What should I do if I encounter difficulties installing the

gas strut?

A: If you face issues with gas strut installation, refer to step
9 for adjusting the opening angle or seek assistance from customer
support.

Q: How do I determine the suitable wall for hanging the

shelf?

A: Ensure your wall has either 2×4 or 2×6 construction and is
suitable for securing hardware to at least one wood stud. Use a
stud finder to locate studs and consider using wall anchors if
needed.

Murphy Shelf w/Secret Drop Down Compartment
murphydoor.com I 888.458.5911

PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY

Tools Needed · Safety glasses · Measuring tape · Pencil or something to mark the wall · Stud finder · Level · Drill · Phillips head driver bit · 1/8″ drill bit · Philips head screwdriver · Adjustable (Crescent) Wrench · 9/64″ Hex Wrench

Shelf Power Jack

Lock Body and Strike USB Power Extension Cable

888.458.5911

USB Power Adapter
Lock Body Screws x4

RFID Cards- x3

Power Jack Screw x4

Strike Screws x2

Wall Plate

Shelf Arm 18″ Hardware ­ x2 34″ and 52″ Hardware ­ x4
3″ Lag Screw 18″ Hardware ­ x4 34″ Hardware ­ x6 52″ Hardware ­ x8

Shelf Slide 18″ Hardware ­ x2 34″ and 52″ Hardware ­ x4

Wall Anchor All Hardware ­ x4

8 x 1″ Screw All Hardware ­ x4

murphydoor.com

PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY

1
Using a mini flathead screwdriver, gently pry up on the metal clip holding the gas strut to the mounting bracket and pull the gas strut to separate the two.

2
Your Murphy Shelf ships with the lock and strike uninstalled. This is to prevent the shelf from becoming locked or accidentally locking the access cards inside the shelf. Put 4 AAA batteries into the lock, program the manager and user cards, and set up the Bluetooth connected app. *Programming instructions can found at the end of this document.

3
After you have put batteries in the lock, use a screwdriver to install it to the pre-marked location in the drop-down shelf with the latch openings towards the front of the shelf.

4
Install the power jack cable through the hole at the back of the drop-down shelf. Plug the backup power jack into the side of the lock.

5
Test the jack in the bottom of the shelf using the included power extension cable. If the power extension cable cannot be fully plugged into the jack, adjust the depth of the power jack through mounting bracket by loosening the two screws in the side of the bracket and pushing the power just through the shelf until the extension cable can be fully plugged in.

6
The front and top panels are pre-drilled to facilitate installation. The strike attaches to the front panel, with the wider set holes aligning with the screw holes in the strike, and the pre-drilled holes in the top panel provide clearance for the push pins to retract.

888.458.5911

murphydoor.com

PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY

7
Remove the snap on cover from the side of the strike to access the screw holes. Align the strike over the screw holes in the front panel and loosely attach using one screw.

8
Depress the push pin opposite the screw you just attached and attach the remaining screw. Fully tighten both screws. Check both push pins and make sure they move freely. Replace the snap on cover.

9
Reattach the gas strut to its mounting bracket by firmly pressing back on. *The opening angle of the drop shelf can be adjusted by loosening the screws for the gas strut bracket and sliding it up or down, then re-tightening the screws. This is easiest to do with the gas strut detached.

10
Determine where you want to place your shelf. Make sure the wall is suitable for hanging the shelf. The wall should have either 2×4 or 2×6 construction. You will need to secure the hardware to at least 1 wood stud, more are preferred. Determine the height you want the top of your shelf, and measure down 3/8″. This will mark the top of the wall plate.

11
Using a stud finder locate and mark the studs. *If you are mounting to a single stud or the ends of the wall plate are more than 2″ (2 mounting holes) away from the nearest stud, the ends of the wall plate will need to be secured with wall anchors.

12
Using a drill, with a Phillips head driver, attach the wall plate using one of the 3″ screws into one of the studs just tight enough that the wall plate can still be rotated by hand.

888.458.5911

murphydoor.com

PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY

13
FOR WALL ANCHORS ONLY Level the wall plate and mark the wall at the mounting holes at each end of the hardware. Use a 1/8″ drill bit and drill all marked locations.

14
The wall anchors provided are self-drilling. Align the drilling point of the anchor with the pilot hole and use a Phillips head screwdriver to drive the anchor into the wall until it stops.

15
Level the wall plate and finish securing the shelf to the wall using additional 3″ lag screws at each stud location and 1″ screws at each wall anchor. Make sure all screws are fully tightened.

16
Align the arms with the holes in the back of your shelf and slide the shelf all the way against the wall.

17
Adjust the shelf side to side until it is where you want it.

18
Pull the shelf back out from the wall 2-3″. Locate the two flat sections near the base of each arm and use an adjustable wrench to turn them clockwise to tighten them into the slide and lock the arm in place.

888.458.5911

murphydoor.com

PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY

19
After you do this at each arm, slide the shelf back against the wall.

20
Insert a 9/64″ hex wrench through each 5/16″ hole in the bottom of the shelf and tighten the retainer onto the wall plate. Slightly lifting the front edge of the shelf while pressing it against the wall can help the clamp fully engage the wall plate.

21
You will want to create cutouts for your belongings in the foam insert before it is installed onto the shelf. Lay your items over the included foam insert, press down firmly on them, then trace the outline using a marker. Remove your items and using a NEW razor knife, carefully cut around the outline. We recommend cutting on the inside of the outline, test fitting your items, then removing additional foam if needed.

22
After you have created the desired cutouts, remove the backing from the foam, align it to the pocket in the drop shelf, and press it into the pocket using one hand behind the shelf to support it.

23
If the batteries in your lock die, your shelf is equipped with a backup power jack. Use the provided USB power cord and adaptor and plug them into the port on the bottom of your shelf to temporarily provide power to the lock and use your access card to unlock it.

24
Congratulations. You have successfully installed your Murphy Shelf with Secret Drop Down Compartment.

888.458.5911

murphydoor.com

PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY

Functions
Batteries

Features
4x AAA 1.5V batteries

Sound Prompt

User Card: · One beep: correct user card · Three beeps: incorrect user card Long beep: door open alarm. Beeps twice when unlocking: low battery alarm.

Light Prompt
Note: The light is on the bottom of the lock and will not be visible once it is installed.

Green: Operation Successful Red: Error/Incorrect Card Blue: Low Battery White: Standby

Alarm Functions
Card Functions Button Functions

Low voltage alarm: 1. When battery’s voltage is lower than 4.5V, the light will shine blue, and lock will beep twice on every unlock to indicate the batteries need to be changed. 2. When voltage is lower than 4V, lock can’t be locked until without the power adapter and will need to have the batteries changed. 3. Lock can normally work several times after low voltage warning.
Lock status alarm: 1. After being open for more than 30 seconds, the door open alarm will sound for 10 seconds and will continue to do so every 30 seconds until the door is closed. 2. *The door open alarm only works in private mode. Pressing buttons 1+2 simultaneously can enable/ disable this feature. 3. This feature can also be enabled/disabled through the app.
Locking protection: An incorrect user card will cause the lock to beep twice and flash the red light twice. 5 consecutive incorrect attempts will disable unlocking for 5 minutes. While unlocking is disabled:
1. The manager card can be used to enable the unlocking. 2. All user cards will cause the lock to beep 5 times.
1. Manager card: Used for programming user cards. 2. User card: Unlocking only. 3. Delete card: Used to remove user cards from the lock.
Button 1: Set manager card. Button 2: Set delete card. Button 3: Change working mode. Button 4: Change to single key mode or double key mode. Reset: Reset the lock. If you don’t want to set lock and card by these four buttons, we also can disable them, and set all with handset machine.

888.458.5911

murphydoor.com

PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY

Lock Modes
1. Private Mode In private mode, when a user card is swiped the lock will stay unlocked for 5 seconds, then lock again.
2. Limited Public Mode In limited public mode, when a user card is swiped the lock will unlock and stay unlocked until the user
card is swiped again.

Functions

Features

Set Private Mode

1. Press and hold button “3” for 2 seconds. 2. The lock will beep twice, and the green light will flash. 3. The lock is now set to private mode.

Set Limited Public Mode

1. Press and hold button “3” for 2 seconds. 2. The lock will beep 3 times and the green light will flash. 3. The lock is now set to limited public mode.

Set Manager Card

1. Press and hold button “1” for 2 seconds. 2. The lock will long beep once and start flashing green. 3. Hold a blank card to the lock. 4. The Lock will beep once. 5. The manager card has been successfully programmed. * Label the card as “MANAGER” or in some other way it can be identified and keep it in a safe location.
This card will be used for programming new user cards or tags only. It cannot be used for unlocking. Up to 10 manager cards can be programmed to the lock.

Set User Card

1. Swipe the manager card. 2. The lock will long beep once and start flashing green. 3. Hold a blank card to the lock. 4. The lock will beep once. 5. The user card has been successfully programmed. 6. To exit user card programming mode swipe the Manager card again. 7. The lock will long beep once and the light will turn white and stop flashing. Up to 30 user cards can be programmed to the lock.

Set Delete Card

1. Press and hold button “2” for 2 seconds. 2. The lock long beep once and start flashing green. 3. Hold a blank card to the lock. 4. The lock will beep once. 5. The delete card has been successfully programmed. * Label the card as “DELETE” or in some other way it can be identified and keep it in a safe location. This card
will be used for deleting user cards or user tags from the lock.

Reset The Lock

1. Press the “Reset” button on the top or bottom of the lock and hold for 2 seconds. 2. The lock will beep 3 times and the green light will flash twice. 3. The lock has been successfully reset and all manager cards and user cards have been removed.

Bluetooth App

1. Make sure the lock is powered.

2. Download the Kerong Admin app from the Apple App Store or Google Play Store to the primary phone you want to use to manage the lock.

Click the link icon in the top right corner to open the list of detected Bluetooth devices.

4. Find your lock in the list. It will be listed by its serial number. · The serial number can be found on the top face of the lock body.
5. Input the pairing password. · This is the PIN located on the top face of the lock by the serial number.
6. Bind your mobile number and input the management verification code. · The default code is 000000. This can be changed in the app once connected.

888.458.5911

murphydoor.com

References

• Hidden Doors | Hidden Bookcase Door | Secret Bookshelf Door – Murphy Door®

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>