Lowes 6513845 LED Modern Contemporary Vanity Light Instruction Manual
- August 27, 2024
- lowes
Table of Contents
Lowes 6513845 LED Modern Contemporary Vanity Light
Specifications
- Item Number: 6513845
- Voltage: 120V
- Maximum Wattage: Type A, Max 60W per bulb
Product Usage Instructions
Preparation and Tools Required
- Before starting assembly and installation, ensure you have the following tools ready.
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Parts Included
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Backplate (1)
- (F) Screw (2)
- (G) Socket (3)
- (H) Lampshade (3)
- (I) Socket ring (3)
Assembly & Installation Instructions
- Carefully unpack all parts and accessories.
- Turn off the power before starting the installation.
- Secure mounting plate (D) to the outlet box using mounting screws (A).
- Connect wires according to the provided charts.
- Connect ground wires as per the chart provided.
- Twist wires together with plastic wire connectors (B) and wrap each connector with electrical tape.
- Tuck all wires carefully into the outlet box.
FAQ
Q: Can I use bulbs with wattage higher than 60W?
A: No, the maximum wattage per bulb should not exceed 60W to ensure safe operation and prevent overheating.
Q: Is it necessary to hire a licensed electrician for installation?
A: While it is recommended to have a licensed electrician install the product, if you are confident in your electrical skills and knowledge, you can proceed with caution following the provided instructions.
Q: What should I do if there are gaps between the mounting surface and the canopy?
A: Any gaps exceeding 3/16 should be corrected as required to ensure proper installation and stability of the product.
Item Number: 6513845
WARNING (To reduce the risk of fire, electric shock, or personal injury).
- We suggest installation by a licensed electrician.
- Please read the instructions carefully and save them as you may need them at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED
NOT INCLUDED
Before starting assembly and installation please prepare the needed tools as below picture
PARTS INCLUDED
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Back plate (1)
- (F) Screw (2)
- (G) Socket (3)
- (H) Lampshade (3)
- (I) Socket ring (3)
ACCESSORIES ENCLOSED
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Turn off power
- Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Make assembly
- Step A1 » Unscrew screws (F) from back plate (E) and mounting plate (D), then set them aside for later installation.
- Step A2 » Carefully pass the supply wires from the outlet box through the mounting plate (D).
- Secure mounting plate (D) to the outlet box with mounting screws (A).
- Step A3 » Make wire connections
- Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the chart below
Connect wires according to the chart below
- Twist wires together with plastic wire connectors (B) until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
- Step A4 » Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed screws (F). Hand tighten until snug.
- NOTE: back plate (E) should be snug against the wall with screws (F).
- If not, remove the back plate (E), and adjust the threaded length of pre-assembled mounting screws on the mounting plate (D):
- Unscrew the pre-assembled hex nuts.
- Screw the pre-assembled mounting screws in or out of the mounting plate (D).
- When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.
- Step A5 »Remove socket rings (I) from sockets (G).
- Carefully hang lampshades (H) onto sockets (G), and then screw socket rings (I) to sockets (G) to secure them.
- When installing socket rings (I), the orientation of socket rings (I) is that the side of the rolled edge faces upward.
- Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
- Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!
ORDERING PARTS
- Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.
CLEANING
- To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>