lowes CA2239-2W Outdoor Wall Lantern Sconce Instruction Manual

lowes CA2239-2W Outdoor Wall Lantern Sconce Instruction Manual

WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE

NOTES:

1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.

To work properly. you should install this fixture NOT confront any jets of air conditions or strong airflow.

1. Attach the mounting plate to the outlet box by using two mounting screws.
2. Pull out the wires and grounding wire from the outlet box. Make wire connections us
   • Connect the hot wire(usually black insulation)from the fixture to the black wire f
   • Connect the neutral wire(usually white insulation)from the fixture to the white w
   • Attach the fixture grounding wire(usually green insulation or bare wire)to the mou grounding screw. Then connect it to the house grounding wire with the wire nut. Carefully put the wires back into the outlet box.
3. Attach the back plate to the mounting plate by inserting the screws,then
   CAUTION: With silicone caulking compound, caulk completely around where the ba wall surface to prevent water from seeping

Turn on the power at fuse or circuit box.

Function and Operation

MODES OF OPERATION

Mode| Works at| ON time| Shut off delay time| Explanation
---|---|---|---|---
Stand-by mode| Day & Night| 20 Sec| /| Turn on the power at the main fuse or circuit breaker box, the light will turn on immediately .Wait for about 20secondstoallow the sensor to warm up, then the light will automatically enter into the TEST mode
Test mode| Day & Night| As motion existing| 5 Sec| The light will turn on at low-level brightness(30%brightness)in test mode. When motion is detected ,thelight will turntohigh-level brightness (100%brightness), andstayonaslongas the motion is continuing. The light will revert tolow-levelbrightness about 5 seconds after motionisnolonger detected. There is one red LED on motion sensor flashing3timeswhenmotion is detected. Note: The time of TEST mode is approximately120seconds, then light will automatically enter into the AUTO mode.
Auto mode| Night only| As motion existing| 2 Min| At dusk, the light will turn on at low-level brightness(30%brightness). When motion is detected, ,thelight will turntohigh-level brightness (100%brightness), andstayonaslongas the motion is continuing. The light will revert tolow-levelbrightness about 120 seconds after motionisnolongerdetected. There is one red LED on motion sensor flashing3timeswhenmotion is detected. Until dawn, the lights will turn off in about 120secondsafterthe motion is no longer detected. Note: If you don’t want low brightness, turnoff andturnonthewall switch twice within 2 seconds when thefixtureisrunning.If you want to restart the low brightness, operatethewallswitch again in the same method. (See FIG.1)
Manual override| Night only| Manual override operat| 8Hrs or Turn off at daw| In “AUTO” mode, to shift to the manual overridemode,turn the wall switch “OFF”, and turn it “ON” within2seconds. The light will turn on and stay onfor approximately8 hours, or until the Dusk-to-Dawn sensor detectslightinthemorning. Once the Dusk-to-Dawn sensor detectslightformore than 60 seconds, the manual overridemodewillautomatically go back to the AUTOmode. (SeeFIG.2)Note: 1. To make sure the above functions operateproperly,always keep the wall switch in the “ON” position(including the daytime). 2. Turn the wall switch “OFF”, wait over 10secondsandthen switch it “ON” again, the light will revert towarm-up period again.

FIG.1 Low Brightness Operating Diagram

Turn wall switch OFF-ON- OFF-ON within 0.5~2sec.

Turn wall switch OFF-ON- OFF-ON within 0.5~2sec.

FIG.2 Manual Override Operating Diagra

NOTE:

1. The sensitivity of the motion sensor will increase as the environmental temperature gets cooler. For best performance, gently clean the lens with a soft cloth every 1 or 2 months to assure maximum sensitivity.

2. For best performance, install fixture at least 6 feet above The ground. At such a height, the lantern will provide a detection distance of up to 40 feet at 77 degrees Fahrenheit .(See Fig.2)
   

3. The sensor detects across a detection range of 220 degrees. (See Fig.3)
   

4. The sensor will be more sensitive to motion across its detection path than motion directly towards it. (See Fig.4)
   

5. To reduce possible nuisances, do not mount the fixture near a heat source like an air conditioner, vent or furnace exhaust, or in a direction facing any reflecting object or other light source.

Troubleshooting

connections.

In Auto mode, the lighting fixture does not turn on when there is motion

| Wall switch or circuit breaker is off| Turn on a switch or circuit breaker.
Light bulb may be dead.| Test the light bulb in a known working light fixture
Light bulb is loose.| Tighten the light bulb in the socket.
Incorrect or loose wire connections.| Check wire connections.
Too much sunlight is shining into theDusk-to-Dawn sensor in the early evening.| Relocate fixture away from a western facing wall.
Too much light is shining onto theDusk-to-Dawn sensor due to another light source, such as a street lamp or other light fixture.| Eliminate or turn off other light source, block other light source from shining onto Dusk-to-Dawn sensor, or relocate fixture.
In Auto mode, the lighting fixture stays on at 100% brightness continuously.| False triggering caused by a heat source, such as a heater or dryer vent, or air conditioning vent ,or heated swimming pool.| Eliminate heat source or relocate fixture
The lighting fixture comes on at 100% brightness for no apparent reason| alse triggering caused by a heat source, such as a heater or dryer vent,or air conditioning vent ,or heated swimming pool.| Eliminate heat source or relocate fixture
The lighting fixture comes on during the daytime or too early in the evening| The fixture may be installed in a shaded area, such as under a porch or eave, preventing daylight from shining onto the photocell sensor.| Relocate the fixture
The LED bulb or fluorescent bulb flickers when the lighting fixture is dimmed down to the stand-by dimming level .| Non-dimmable LED bulb or fluorescent bulb is used on the lighting fixture.| Replace dimmable LED bulb or fluorescent bulb, or incandescent bulb
In Manual override, the light stays on after dawn| the ambient light level is too low| Relocate the fixture

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>