Lowes HA05316 Light Plated Chrome Modern Contemporary LED Dry Rated Installation Guide
- June 1, 2024
- lowes
Table of Contents
Lowes HA05316 Light Plated Chrome Modern Contemporary LED Dry Rated
INSTALLATION GUIDE
Item Number:A05316
WARNING (To reduce the risk of fire, electric shock, or personal injury):
1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a
later time.
3. Before you start, NEVER attempt any work without shutting off the
electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger
than the canopy on all sides. Any gaps between the mounting surface and canopy
exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before
installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is LED,
38W.
7. Keep the lamp away from acidic and alkaline substances in case of damaging
the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must
wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover
all possible conditions that may occur. It must be understood that common
sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture
PARTS TYPE & QTY INCLUDED:
(C) Mounting plate (1)
(D) Canopy (1)
(E) Canopy screw (3)
(F) Lock nut (4)
(G) Steel wire (3)
(H) Cable (1)
(I) Frame (1)
(J) Resin decorative sheet (10)
(K) Sheet nut (20)
(L) Quick link (1)
ACCESSORIES & QTY ENCLOSED:
(A) Mounting screw (2)
(B) Plastic Wire Connector (3)
(K) Sheet nut (4) (spare part)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
1. Carefully remove the fixture from the carton and check that all parts and
accessories are included as shown in the above illustration.
2. Turn off power
Before you start the installation, NEVER attempt any work without shutting off
the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
3 » Unscrew canopy screws (E) from canopy (D) then gently remove mounting plate (C).
» To adjust the hanging height of the fixture:
- Screw lock sleeves from lock nuts (F).
- Press down and hold lock nut (F) by hand.
- Pull or push steel wires (G) and cable (H) in and out of canopy (D) to increase or decrease the hanging height.
- Please adjust steel wires (G) first.
- Screw lock sleeves back to lock nuts (F) as shown in the illustration.
5 » Carefully pass supply wires through mounting plate (C).
Secure mounting plate (C) to the outlet box with mounting screws (A).
OUTLET BOX
6. Make wire connections
Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS
BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the chart below
Connect wires according to the chart below
| Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
|---|---|
| Black | White |
| *Parallel cord (round & smooth) | *Parallel cord (square & ridged) |
| Clear, Brown, Gold or Black without tracer | Clear, Brown, Gold or Black with |
tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other
than green) with silver conductor
-
Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
- Twist wires together with plastic wire connector (C) until tightly joined.
- Wrap each connector with approved electrical tape for a more secure connection.
- Carefully tuck all wires into the outlet box.
7 >> 1) Open quick link (L), and then hang it onto the mounting plate (C)
as shown in the illustration.
2) Fix canopy (D) to mounting plate (C) and secure with the previously removed
canopy screws (E).
8 » Align holes of resin decorative sheets (J) and holes of frame (I), and then screw sheet nuts (K) into nipple of frame (I) to secure them as shown in the illustration.
9. Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Specifications:
-
Item Number: A05316
-
Maximum Wattage: LED, 38W
-
Voltage: 120V
-
-
FAQ
Q: Can I install the lamp without a licensed electrician?
A: It is recommended to have the lamp installed by a licensed electrician for safety reasons.
Q: What should I do if the mounting surface is not strong enough?
A: Ensure the mounting surface is clean, dry, flat, and strong enough. Any gaps exceeding 3/16 should be corrected.
Q: How do I adjust the hanging height of the lamp?
A: Pull or push the steel wires and cable in and out of the canopy to increase or decrease the hanging height.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>