VL55603BBZ Yellowstone 3-Light Moose

Product Information

Specifications:

• Model: VL55603BBZ
• Max Wattage: 100W Type A Bulb (not included)
• Material: Glass, Metal
• Warranty: 1 Year

Product Usage Instructions

Installation Steps:

1. Turn off the power at fuse or circuit box.

2. Unscrew two bolt nuts (C) and remove the mounting plate from
   the backplate.

   • For wooden material:

   1. Attach the mounting plate to the outlet box using two mounting
      screws (A).

   2. Secure the plate to the wall with drywall screws (E) through
      the set holes.

   • For cement material:

   1. Place the mounting plate on the outlet box and mark the target
      on the wall for drilling holes.

   2. Thread anchors (D) into the holes, then attach the plate to the
      outlet box using mounting screws (A).

   3. Secure the plate to the wall with drywall screws (E) through
      the set holes into the anchors (D).

3. Install the silhouettes onto the backplate.

4. Align the hole in the backplate with the slot in the silhouette
   clip and secure with a set screw.

5. Repeat for each silhouette following the sequence shown in
   Fig.1 and Fig.2.

6. Attach the backplate to the mounting plate with screws and bolt
   nuts (C).

7. Attach glass shades to glass holders and secure with socket
   rings.

8. Install 3 x 100W Max. Medium Base Bulbs (not included).

9. Turn on the power at fuse or circuit box.

Frequently Asked Questions (FAQ)

Q: What should I do if any parts are damaged or missing?

A: The following parts are available for reorder if damaged or
missing: Assembly Kit 6537MM (1 SET), Mounting Screw (A), Wire
Connector (B), Bolt Nut (C), Anchor (D), Drywall Screw (E), Glass
Shade 938351.

Q: What is covered under the warranty?

A: Vaxcel warrants all products against defects in workmanship
and finishes for one year. Exclusions include failure due to
extreme acts of nature, unsuitable environmental conditions,
improper power supply, and usage outside specified temperature
ranges.

Q: How can I claim warranty service?

A: Vaxcel reserves the right to repair, replace, or issue a
credit for properly installed products returned per RMA
instructions. The warranty is limited to the product cost and does
not cover transportation, installation, or replacement costs.

ASSEMBLY AND INSTALLATION INSTRUCTIONS
VL55603BBZ
WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save this instruction.
Hardware Package (included):

Mounting Screw (A)

Wire Connector (B)

Bolt Nut (C)

Anchor (D) Mounting Screw (A)
Screw Mounting Plate

Bolt Nut (C)
Max.100W Type A Bulb (not included)

Backplate Glass Holder Glass Shade
Socket Ring

Anchor (D)

Drywall Screw (E)

Outlet Box
Wire Connector (B) House Ground Wire
Set Hole Drywall Screw (E) Green Ground Screw Fixture Wire Fixture Ground Wire

“L” Clip V-B3 V-C
Set Screw
Backplate

V-E

V-B2

V-C V-D

V-C

V-B1

V-B3 “L” Clip Set Screw Backplate
Fig.1 Fig.2

Page 1 / 2

230821

Installation Steps
Turn off the power at fuse or circuit box.
1. Unscrew two bolt nuts (C) and remove the mounting plate from the backplate. 2. Fix the mounting plate to the wall.
a) For wooden material: Attach the mounting plate to the outlet box by using two mounting screws (A), and then secure the drywall screws (E) through the set holes to the wall.
b) For cement material: Place the mounting plate to the outlet box and mark the target on the wall from the set hole for drilling two holes. Remove the mounting plate from the outlet box. Thread the anchors (D) into the holes, then attach the mounting plate to the outlet box by using two mounting screws (A). Secure the drywall screws (E) through the set holes into the anchors (D).
3. Install the silhouettes onto the backplate. a. Take a silhouette and place it onto the backplate with the hole in the backplate aligning the slot in the clip of the silhouette, secure it with a set screw. (See Fig.2) b. Repeat with the other silhouettes. c. Please follow the sequence shown in Fig.1 to install the silhouettes onto the backplate.
4. Pull out the source wires from the outlet box. Make wire connections using wire connectors (B) as follows: · Connect the hot wire (black insulation) from the fixture to the black wire from the power source. · Connect the neutral wire (white insulation) from the fixture to the white wire from the power source. · Attach the fixture ground wire (bare wire) to the mounting plate with the green ground screw, then depending on local code, connect it to the house ground wire with the wire connector (B). Carefully put the wires back into the outlet box.
5. Attach the backplate to the mounting plate by inserting the screws, secure it with two bolt nuts (C). 6. Attach the glass shades to the glass holders, secure them with the socket rings. 7. Install 3 x 100W Max. Medium Base Bulbs (not included). See relamping label at socket area or packaging for
maximum wattage allowed.
Turn on the power at fuse or circuit box.
The following parts are available for reorder if damaged or missing.
B
Spare Parts List:

Assembly Kit 6537MM (1 SET)

A

Mounting Screw (A)

Wire Connector (B)

Bolt Nut (C)

Anchor (D)

Drywall Screw (E)

Glass Shade 938351

C A: 14″ B: 25-1/4″ C: 8″

1 Year Warranty
Vaxcel warrants all of our products against defects in workmanship and finishes for one year following the date of shipment.
Exclusions: This warranty does not include the failure of products from extreme acts of nature; environmental conditions not suited for the products intended use; operation in temperatures outside of the range specified in the instruction manual; usage with improper power supply, power surges or dips. For coastal locations, some corrosion is considered normal for the environment.
Vaxcel reserves the right to repair, replace or issue a credit for any properly installed product, provided it is returned per RMA instruction. This warranty is limited to the cost of the product only and does not extend to transportation, installation or replacement costs.
How can warranty service be obtained? info@vaxcel.com 1-800-482-9235

Page 2 / 2

230821

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>