The Home Depot F-300, 40KHZ Ultrasonic Cleaner Machine Instruction Manual
- August 26, 2024
- THE HOME DEPOT
Table of Contents
The Home Depot F-300, 40KHZ Ultrasonic Cleaner Machine
Specifications:
- Model: F-300/40KHZ
- Tank size: L600W450H400MM
- Ultrasonic Power: 1500W
- Heating Power: 3KW
- Frequency: 40kHz
- Capacity: 108L
- Voltage: 220V
Product Usage Instructions
Setup:
- Place the ultrasonic cleaner on a flat surface and ensure it is properly grounded.
- Connect the power wire and ultrasonic cable correctly.
- Connect the drain pipe to the factory drainage system.
Operation:
- Fill the tank with the cleaning liquid up to the working surface.
- Set the temperature as required and turn on the heater switch.
- Adjust the ultrasonic power to a minimum, then start the ultrasonic function and adjust the power to the desired level after normal vibration is established.
Maintenance:
- Regularly clean dust from the control system using high-pressure air blasts.
- Clean the tank at least once a week to maintain optimal performance.
-
Power supply issue:
- Question: Power supply not connecting?
- Possible reasons: Power switch not plugged in.
- Solution: Check and plug in the power switch.
-
Fuse problem:
- Question: Fuse broken?
- Possible reasons: Incorrectly fitted power supply.
- Solution: Check the power supply connection and fuse.
-
Cable issues:
- Question: Cable short circuit?
- Possible reasons: Cable malfunction.
- Solution: Check the cable for any short circuits or damages.
Working Conditions
Please ensure the correct power and switch connection before starting the equipment. Be careful that the control panel will be corrosive under the condition of organic solution, strong acid and strong base.
Do not use the product under the condition of :
- Where temperature fluctuates strongly
- Where it has high humidity and especially dew
- Where vibration or shock is strong
- Where corrosive gas or dust exist
- Where water, oil or chemicals splash.
- Where is easy to cause an explosion.
Machine Features:
- Power supply: Machine AC220V
- Room temperature: -10°C~40°C
- Room humidity: 35~85%
- Machine No: 2020F18
General
Single tank ultrasonic cleaner are industrial models in industrial field, made of high quality SUS stainless steel plate, corrosion resistance and long lifespan, adopt with high technology ultrasonic transducer and advanced adhesive technology, high electro-acoustic conversion efficiency and strong ultrasonic power output.
Equipped with automatic constant temperature heating device, heating range: room temperature* 95°C.
Ultrasonic cleaner widely applied to industry of precision electronics, painting, semi-conductor, filter system, watch-clocks, glass, metal, jewelry, and medical instruments cleaning etc. Structure & Function
- Ultrasonic generator: output frequency is 40 KHz (40/68/80/120/132KHZ are available for customized model). Equipped with sweep function and compensation circuit, strong anti-interference ability, and high output frequency precision.
- Transducer: Convert electric power into Hi-Fi mechanical vibration energy, with broad band frequency, high power and high stability.
- Heating system: Automatic constant temperature heating systems, made up of heating panel, digital timer and temperature switch.
- Machine structure: with separate generator control
- Timer : timer can be set by customer upon requirement 1-99min
- Temperature : set temperature based on your demand, 20°C~ 80 °C can be setted.
- Ultrasonic control:
1. **ultrasonic tank:** equipped with 40kHz 30pcs transducers,1500W.
2. **Ultrasonic tank:** equipped with 3KW HEATING.
3. **Generator structure:**
Function instruction
( Note : The generator parameters have been set before shipment. Please don’toperate the buttons except the power switch and the power adjust knob if there is no professional guidance.)
F/l: Function switch: Continuously press the button, the display window will switchover current/frequency/mode.
- Current display: X.XXA, A displays amps.
- Frequency display: FXXX or FXX.X, F displays frequency.
- Mode display: it has three cases: timer mode, normally open mode and remote control mode.
- Timer mode: TXXX, in minute. Press +/- button can set the time. Press TIME to start the timer and machine will automatically off.
- Normally open mode: it will displays ON. Press the TIME and + button at the same time to set it.
- Remote control mode: Press the Time and – button at the same time to set it.
If need to switch over the machine to timer mode when the machine is under normally open mode and remote control mode, please press + and – button at the same time.
Operation panel
Ultrasonic cleaning principle:
The ultrasonic cleaner uses transducers to generate sound waves; the frequency
is 40KHz. When the sound waves travel through the liquid, millions of tiny
bubbles form and burst continuously. This process is called a “cavitation”
effect. The bursting bubbles scrub everywhere the liquid can penetrate.
Intricate surfaces and difficult access areas, such as burs, endodontic files,
serrated instrument handles, and hinged instruments, are cleaned more
thoroughly and rapidly but no damage to cleaning objects. The cavitation is
basic theory of ultrasonic. ultrasonic cleaner suits for aqueous solution,
neutral liquid is suggested. Strong acid, strong alkali and flammable liquids
are forbidden.
Cautions before start the machine:
Place all buttons on “OFF”.
- Cleaning liquid is ready in tank, Empty tank working is forbidden!
- Don’t let the liquid splash into the electronic parts, especially transducers.
- Start the ultrasonic when liquid temperature reaches we set.
- Don’t start heating if no liquid or liquid level is lower than work level, or heating pad will be damaged.
- Don’t contact the bottom directly (vibration plate), may damage the transducers.
- Keep the machine in dry and cool environment.
- The generator power supply is 220V 50HZ and should be earthing.
- Cover the lid to reduce noise and attention to liquid drop and evaporation.
- Wash the tank if there is much deposit in the tank
- Don’t pull the inside liquid out if liquid temperature is not close to room temperature, to avoid the side tank which equip with heating tube deform.
- Don’t move the machine when there is a liquid inside tank to avoid splash.
- The machine power supply is AC220V and must be grounded.
Main parameters
Instructions:
- Keep the machine on a flat floor and must be grounded
- Connect the power wire and ultrasonic cable correctly.
- Connect the drain pipe with factory drainage system
- Put into cleaning liquid to the working surface.
- Set temperature based on requirement and turn on the heater switch.
- Adjust ultrasonic power to Min., then start ultrasonic and adjust ultrasonic power to requirement after normal vibration.
Maintenance
- Use high-pressure blast to clean dust of the control system regularly
- Clean the tank once a week at least
Trouble clearing
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>