ROVIN Portable Multipurpose Cabinet Camping Light User Manual
- June 7, 2024
- ROVIN
Table of Contents
ROVIN Portable Multipurpose Cabinet Camping Light User Manual
Standard Configuration
Lamp ×1
USB transfer to DC3.5 **USB cable ×1
Three-in-one Baseholder ×1
（Screw+3M tape）×1**
Charging instructions
Charger with output voltage 5V only Do not use charger with output voltage＞5V or current ＞ 2A
USB length: 100cm
laptop USB **interface
power adapter
mobile power**
Parameter
| Bead quantity | 20pcs 3000K warm white, 20pcs 6500K cold white |
|---|---|
| CCT | stepless dimming( switch among 3000K-4000K-6000K) |
| Power | 2.5W |
| Warranty | 2 years |
| luminous flux | 200LM |
| Battery Type | 3.7V 2000mAh Lithium Battery |
| Charging Tme | 2 hours get 90% power 3 hours get 100% |
| Run Time | 4-10(high-light level-50% level) |
| Charge indicator | under charging turn to red color, finished charging turn to |
green color
Interface spec| DC3.5V
Waterproof grade| IP20
Materia| Iron+ABS plug
Notices:
- Do not take apart and change interior parts by yourself
- Do not look straight under strong light state in case of eye damage
- Do not put lamp under high temperature and moist environment
- Do not spray any liquid to lamp and put it together with flammable material
- Do not charge for too long, cut off power when you leave.
Operating Guide
Short touch– on/CCT change/off
Long press–stepless dimming(2-100%) Switch Position: one end with switch sign on the plastic plug
Short touch: First touch: 40pcs beads light up with 4000K ( natural
white) Second touch: 20pcs beads light up with 6500K(cold white)
Third touch: 20pcs beads light up with 3000K ( warm white) Fourth touch: goes
into SOS flashing mode Fifth touch: back to ready mode until next touch for
the next cycle Long press: under lighted state, take a long press will achieve
stepless dimming. If you take a short touch, the brightness still keep the
same level of last one
Notices:
- For wall mounted, try to put baseholder in the middle of the lamp
- For ceiling mounted, try to put baseholder close to battery part as it’s heavier than the other side so as to keep gravity balance
- Avoid violent shaking in case of falling caused by gravity imbalance
Installation
MAGNET
Please ensure adsorbed iron material have enough density, otherwise, the lamp
might fall caused by short weight; If the adsorption surface is curved, the
lamp might fall as the incomplete absorb surface result in weakness suction.
B.3M double-side tape
Double faced
+
**adhesive tap
**
Adjustable light direction Please ensure pasted surface keep smooth, dry, free of oil and dirt in case of falling. Stick one side to base holder and press hard for 2 minutes, tear off the other side and paste it where you want and give another 2 minutes hard press.
**C. Screw
**
Please prepare your own cross screwdriver and tighten it up in the right position.
safety tips
- Do not charge with output voltage 5V, otherwise, the main control IC might be destroyed, which will lead to circuit board protection functions fails and damage battery.
- Do not charge with current 2A.
- If charge with light on state, ensure keep bightness level 90% to avoid full load operation effect product function, and try not charge 2 hours with light on state.
- Do not charge for long time, please cut off power if charged.
- Any interior parts are not allowed to be taken apart, fixed and replaced; do not put lamp under high temperature and moist environment and put it together with flammable material
Distributed by: TechBrands by Electus Distribution Pty. Ltd. 320 Victoria Rd, Rydalmere NSW 2116 Australia Ph: 1300 738 555 Int’l: +61 2 8832 3200 Fax: 1300 738 500 www.techbrands.com Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>