EDIFIER EDF100081 Studio Monitor Speakers User Guide

EDIFIER EDF100081 Studio Monitor Speakers

Specifications

• Model: #.3 .3#7
• Type: Studio Monitor
• Brand: JP
• Color: HEB

Product Usage Instructions

Setting Up the Studio Monitor

1. Place the studio monitor on a stable surface at ear level.
2. Connect the monitor to your audio source using the appropriate cables.
3. Ensure the power source is connected and turned on.

Adjusting Settings

Use the controls on the studio monitor to adjust volume, bass, treble, and other settings according to your preferences.

Optimizing Sound Quality

Experiment with the positioning of the studio monitor in your space to achieve the best sound quality.

FAQs

Q: How do I clean the studio monitor?

A: Use a soft, dry cloth to gently wipe the exterior of the monitor. Avoid using liquid cleaners or abrasive materials.

Q: Can I connect multiple audio sources to the studio monitor?

A: Most studio monitors are designed to accept one audio input at a time. If you need to connect multiple sources, consider using a mixer or audio switcher.

What’s in the box

Note:

• Images are for illustrative purposes only and may differ from the actual product.
• For the need of technical improvement and system upgrade, the information and specifications contained herein may be slightly different from the actual product. If any difference is found, tho actual graduate voila

Cable connection

Note:

• Power input: 100-240V~ 50/60Hz 300mA
• This plug type is meant for illustrative purpose only.
• All audio inputs including Bluetooth connection can be used in parallel.
• The speaker will be muted when you connect your headphones to the “A” port. You can control the headphone volume with the volume knob on the speaker.

Power on/off

• Total output power (RMS): 18W+18W (DRC on)
• Frequency response: 60H7-40kH>

Bluetooth connection

Note:

• The pin code for connection is “0000” if needed.
• To enjoy all the Bluetooth functions of this product, make sure that your audio source device supports A2DP and AVRCP profiles.
• If no device is connected in 3 minutes, the speaker will switch to Bluetooth hidden mode. In this mode, (1) new devices cannot find the speaker, but (2) for a device that exists in the pairing recordof this speaker, you can select “EDIFIER MR3” from its Bluetooth device list to reconnect. To exit from Bluetooth hidden mode, press the “*” button on the speaker.
• To disconnect from the current Bluetooth device, press and hold the “*,” button on the speaker for 1.5 seconds. This speaker supports the simultaneous connection of two Bluetooth devices.
  • Connect the first Bluetooth device to the speaker.
  • Press and hold the “*” button on the speaker for 1.5 seconds.
  • On the second Bluetooth device, select “EDIFIER MR3” in its Bluetooth device list to connect.
  • On the first Bluetooth device, select “EDIFIER MR3” in its Bluetooth device list to reconnect.
• Pause or stop playback on the current Bluetooth device before streaming audio from the second one.

Sound effects

Volume adjustment

Note.

• The volume levels of the speaker and your device are not synchronized. To adjust the volume levels,

Acoustic tuning

• “High” knob: Adjust the gain of high frequencies.
• “Low” knob: Adjust the gain of low frequencies.
• Low cutoff: Attenuate frequencies lower than the specified frequency (20-100Hz) at a selected slope (6, 12, 18, or 24dB/octave). Aussies, odes Solet an in the heel to e often ate more bas bo bet, lih ecoser. The closer the speaker is to a wall or corner, the smaller the value is to be set. Desktop control: When the speaker is placed on a desktop or an object is placed in front of it, there may be an apparent increase in the decibel level at certain frequencies. Enable the feature to mitigate this effect.

EDIFIER ConneX app

1. With your smart device, scan the QR code on the quick start guide or the packaging.
   • You can also search for “EDIFIER ConneX” in the Apple App Store (iOS devices) or Google Play (Android= devices).
2. Download and install the app.
3. Connect your smart device with the speaker via Bluetooth.
4. In Bluetooth mode, open the EDIFIER ConneX App on your smart device.
5. Tan the menu for settings and playback control.

WARRANTY

• To learn more about EDIFIER, please visit www.edifier.com
• For EDIFIER warranty queries, please visit the relevant country page on www.edifier.com and review the section titled Warranty Terms.
• USA and Canada: service@edifier.ca
• South America: Please visit www.edifier.com (English) or www.edifierla.com (Spanish/ Portuguese) for local contact information.

Hereby, Edifier International Limited declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: https://www.edifier.com/global/eu-doc

Declaration for EU Ff Power sput 4026 – 24306H2 There is no restriction of use.

FCC

FCC Regulatory Compliance

Warning : changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

SED Regulatory compliance

This device contains license-exempt transmitters that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Important safety instruction

• Please read the instructions carefully. Keep it in a safe place for future reference.
• Use only accessories approved by the manufacturer.
• Install the instrument properly by following the instructions in the device connection section.
• Using the product in a 0-35°C environment is recommended. Shipping and storing the product in a 0-35°C environment is recommended.
• To reduce the risk of fire and electric shock, do not expose the product to rain or moisture.
• Do not use this product near water. Do not immerse the product in any liquid or have it exposed to dripping or splashing.
• Do not install or use this product near any heat source (e.g. radiator, heater, stove, or other devices that generate heat).
• Do not place any object filled with liquids, such as vases on the product; neither should any open fire, such as lit candles be placed on the product.
• Do not block any ventilation openings. Do not insert any object into ventilation openings or slots. It may cause fire or electric shock. sufficient clearance around the product to maintain good ventilation (minimum 5cm is recommended).
• Keep
• Do not force a plug into the jack. Before connection, check for blockage in the jack and whether the plug matches the jack and is oriented in the right direction.
• Keep the provided accessories and parts (such as screws) away from children to prevent them from being swallowed by mistake.
• Do not open or remove the housing yourself. It may expose you to dangerous voltage or other hazardous risks. Regardless of the cause of the damage (such as damaged wire or plug, exposure to liquid splash or foreign object falling in, exposure to rain or moisture, product not working or being dropped, etc.), the repair has to be performed by an authorized service professional immediately.
• Before cleaning the product with a dry cloth, always turn off the product and disconnect the power plug first.
• Never use strong acids, alkalis, gasoline, alcohol, or other chemical solvents to clean the product surface. Use only neutral solvent or clear water for cleaning.
• The product must be used at an altitude of lower than 2000m. • The MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable.

Correct Disposal of this product. This marking indicates that this product should not be disposed of with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycling it responsibly to promote sustainable products was pual has. Yenturk our prod device peron menthe set recycling collection systems or contact the retailer where the Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Excessively loud music may lead to hearing loss. Please keep the volume in a safe range.

Power warning:

• Place the product near the power outlet for easy use.
• Before use, make sure that the operating voltage is the same as your local power supply. Correct operating voltage can be found on the product plate
• For safety purposes, unplug the product during lightning storms or when unused for extended periods of time.
• Under normal conditions, the power supply may get hot. Please keep good ventilation in the area and exercise caution.
• Product nameplate and safety warning labels on the housing or bottom of the product or power adaptor.
• This symbol is to alert the user to the presence of un-insulated dangerous
• This symbol indicates that the product is for indo voltage within the product’s enclosure which may be of sufficient use only. magnitude to constitute a risk of electric shock to persons.
• This symbol is to warn the user not to disassemble the enclosure of theproduct and there is no user-replaceable part inside. Take the product to an authorized service center for repair.
• This symbol indicates that the product is a
• CLASS Il or double insulated electrical device with no earth requirement.

CONTACT INFORMATION

• Edifier International Limited
• P.O. Box 6264
• General Post Office
• Hong Kong
• Tel: +852 2522 6989
• Fax: +852 2522 1989
• www.edifier.com
• © 2024 Edifier International Limited. All rights reserved. Printed in China
• @Edifierglobal
• @Edifier_Global
• @Edifier_Global

NOTICE:

• For the need of technical improvement and system upgrade, information contained herein maybe subject to change from time to time without prior notice. Products of EDIFIER will be customized for different applications. Pictures and illustrations shownon this manual may be slightly different from the actual product. If any difference is found, the actual product prevails.

References

• Headphones, Speakers | A Passion for Sound -【Edifier】

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>