nordlux 497010XX Canto 2 Outdoor Up Down LED Wall Light Instruction Manual
- August 26, 2024
- nordlux
Table of Contents
nordlux 497010XX Canto 2 Outdoor Up Down LED Wall Light
Product Information
Specifications
- Material: Copper, Brass, Tombac, Galvanized
- Guarantee: Up to 15 years for extensive corrosion caused by rust
- Surface Coating: Varied coating leaving a rustic appearance
Product Usage Instructions
Outdoor Lamp Maintenance
Take care of your outdoor lamp by following these guidelines:
- For Stainless Steel lamps, ensure drainage holes are free of impurities.
- Regularly wipe off all parts before reassembling the bollard.
Cleaning Instructions
To maintain the appearance of your lamp:
- Condensation can be removed with a soft brush.
- For Copper, Brass, and Tombac lamps, use a soft brush to remove any accumulated material.
FAQ (Frequently Asked Questions)
Q: What is the guarantee period for the outdoor lamps?
A: The outdoor lamps in copper, brass, tombac, and galvanized have a guarantee
of up to 15 years for extensive corrosion causedby rust, subject to
presentation of the receipt.
Non replaceable light source
Mounting instruction
- IP4X: Protected against solid objects with a diameter of 1.0 mm or more. Hazardous parts are shielded from contact being made using wires etc.
- IPX4: Raindrops falling from any angle will not affect the function/safety of the lamp.
- The lamp is only suitable for connecting directly to the mains.
- Class I: The lamp has an earth terminal and must be connected to the yellow/green earth wire.
- IMPORTANT! Always shut off power to the circuit before starting installation work. In some countries electrical installation work may only be carried out by a authorized electrical contractor. Contact your local electricity authority for advice.
- This product contains a light source of energy efficiency class
. - Disposal of waste equipment by users in private households in the European Union. This symbol indicates that this product must not be disposed of with your other household waste. Electrical and electronic equipment contain substances which may cause damage to human health and environment if not recycled correctly. It is your responsibility to hand over to a designated collection point for recycling of waste electrical and electronic equipment. When handing over for correct recycling you help to prevent these products straining nature and environment unnecessarily and to protect human health. For more information regarding correct disposal, please contact your local city office, your household waste disposal service or the store where you purchased this product.
- Parallel arranging possible.
- The mounting instruction must not be discarded.
In the Nordic Countries, outdoor lights must be mounted by an authorised
electrician.
We congratulate you on your new outdoor lamp!
We congratulate you on your new outdoor lamp!
Guarantee
The Nordlux Outdoor lamps in copper, brass, tombac and galvanized are
guaranteed for up to 15 years. This guarantee applies to extensive corrosion
in the form of holes in the metal caused by rust. The guarantee is subject to
presentation of receipt.
There is not guarantee on the components which have been damaged by wear and
tear or mistreatment of the lamps
We congratulate you on your new outdoor lamp
Stainless steel
Remember to take care of your lamp. Just follow the guidelines below. The
shiny, uniform and decorative surface of stainless steel makes it very
suitable for outdoor use.
It is an alloy consisting of iron, chrome and nickel.
During bath pickling, a thin, rustproof oxide layer forms on the surface. The
surface is continually vulnerable to atmospheric conditions, and from other
effects of the close environment. This means that the lamp must be regularly
maintained if its surface is to remain shiny and untar- nished by rust.
Before setting it up, treat your lamp with acid-free oil, and dry it off with
a soft cloth. Repeat this three or four times a year. Stainless steel lamps
are not recommended for use in aggressive environments such as coastal,
agricultural or industrial areas.
Copper, Brass and Tombac fixtures
Our copper, brass and tombac fixtures are made from respectively solid copper,
brass and tombac. The mechanical machining will leave small scratches in the
surface, as well as residues of rinse aid. This rapidly disappears in the
patina process. After the first rain showers the copper/brass / tombak surface
will appear stained, but the aerated air and moisture will soon make the lamp
appear with dark brownish color. Over the years, the material copper will get
a beautiful patina-green color and brass / tombac will get a darker and more
uniform color. The uniformity of the patina surface, as well as the rate at
which the process occurs is dependent on the environment that affect the
fixture.
Hot-galvanized lamps
The zinc treatment of the steel lamps is executed manually in plants. The
temperature of the melted zinc is about 460 degrees. When the lamps are dipped
in melted zinc a reaction between the metalls occurs, which develops alloys in
the surface. The lamp and the components of the lamp are manually dipped in
the hot zinc. This treatment leaves variations in the coating in the form of
partly an uneven surface and partly minor formations of drops. Thin »zinc
curtains« might also occur on the surface and they show as a thin film that
hangs down from the edge of the lamp. This film can easily be removed or
brushed off with a soft brush.
Condensation
Condensation is a natural phenomenon arising under specific atmospheric
conditions. Damp heat and cold air meet, which causes conden- sation of water
on the surface. When water heats up it leads to rising water vapour, which
will be able to affect electric components. Condensation is not included by
Nordlux warranty, unless it is possible to prove that a technical /production
error in the lighting causes entry of water. In case of condensation please
check:
- If the lighting is mounted according to instructions. Washers should seal tightly. Make sure to tension screws and lenses.
- In garden lightings rising damp from the ground may cause condensa
Aluminium
fixtures Our aluminium light fixtures are made from die-cast and/or extruded
aluminium, where the light fixture’s design determines whether both types of
materials, or just one of them, are used for different parts of the same light
fixture. Aluminium light fixtures in raw aluminium are subsequently coated
with a special clear coat, which seals the surface to safeguard against
corrosion. Painted aluminium light fixtures are powder-coated and have a
uniform and smooth surface. To avoid the light fixture tarnishing, it is
recommended to clean and wipe the light fixture after mounting, and repeat
this process 3-4 times each year. This is done with a regular cleaning agent.
Black light fixtures which are bleached by strong sunlight can also benefit
from treatment with silicone spray as needed, to maintain the black color.
Mounting light fixtures in coastal, agricultural or industrial areas is not
recommended, as these aggressive surroundings may cause the light fixture to
corrode, which may entail spalling, bubbles in the surface and a whitish
incrustation on the light fixture’s surface.
It is highly important that drainage holes are kept free of impurities if any.
BEFORE ASSEMBLING THE BOLLARD AGAIN DO REMEMBER TO WIPE OFF ALL PARTS!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>