HOLMAN CO6002 Dual Outlet Tap Timer User Guide

HOLMAN CO6002 Dual Outlet Tap Timer

Overview

Main Components

1. ZONE 1 outlet
2. ZONE 2 outlet
   • Each outlet is 20mm BSP with 12mm snap-on connection included
3. 20/25mm BSP tap nut inlet
4. Tap connection locking nut
5. Display
6. ON/OFF
7. MENU DIAL
8. Battery compartment:
   • Requires 2× AA alkaline batteries only (not included)

Function and Resetting

• Inactivity on your QuikDial Tap Timer controls for 10 seconds will return to the default system mode displaying the current time
• Removing the AA batteries will reset all clock and schedule settings
• To reset your QuikDial, remove the batteries for 2 minutes which will return the timer to factory default
• For use with cold water only

Specifications

Precautions and Use

• Your QuikDial is designed to hang vertically from a tap
• Do not use in place of irrigation solenoids
• Use with caution on short run drip systems, these can keep valves open when they need to close. A pressure reducer is recommended

Setup

Battery Installation

1. Install 2× 1.5v AA alkaline batteries into your QuikDial Tap Timer, as indicated in the battery compartment [a]
   • After installing the batteries, the display will flash ZONE I, then ZONE II as part of start up
   • Once the start-up process is complete, the CLOCK will display as follows, with the time separator flashing [b] and the battery indicated as full [c]

Setup Process

• Your QuikDial has a simple and intuitive setup system quickly completed in 5 steps
• Your QuikDial has up to 4 START TIMES available
• RUN TIMES between 1–99 min per ZONE
• ZONES will water sequentially starting from the set START TIME
• 1 or 2 ZONES can be included in each START, for a total of up to 8 possible waterings (2 ZONES, 4 times per day) to be set
• As an example, if you set a START with a RUN TIME of 60 min this will give a total of 2 hours of watering when both ZONES are included in the start
• For automatic watering, you must ensure that the CLOCK, START TIME, RUN TIME, SET DAY and ZONE have all been set correctly
• Here is a quick overview to see how all these settings combine into an automated watering schedule for your garden

Set Clock

• The current time and day of the week is needed as the reference point for your program to work
• The CLOCK is in 24hr time (12:00 is midday and 00:00 is midnight)

1. To set the clock, turn your MENU DIAL anti-clockwise (left) or clockwise (right) until the time is flashing [a]
2. Press the MENU DIAL once and the HOUR will flash [b]
3. Turn the MENU DIAL to set the HOUR of the current time
4. Press the MENU DIAL and the MINUTES will flash [c]
5. Turn the MENU DIAL to select the MINUTES of the current time
6. Press the MENU DIAL and DAYS will flash [d]
7. Turn the MENU DIAL to select the current DAY of the week
8. Press the MENU DIAL to complete this step

Starts

• Your QuikDial has up to 4 START TIMES available, these can be used for 1 or both ZONES as needed
• There is a default time set for each START. To see these, turn the MENU DIAL clockwise (right)
• While START 1 is on, STARTS 2, 3 and 4 are set to OFF
• The START TIMES are in 24hr time
• 00:00 is midnight and 12:00 is midday
• Default START TIMES are as follows:
  • L START 1—07:30
  • L START 2—09:30
  • L START 3—15:30 (3.30pm)
  • L START 4—18:30 (6.30pm)

Turn a Start On/Off

• Begin by turning the MENU DIAL clockwise (right) until you see the START NUMBER (1, 2, 3 or 4) you want to select
• If the START is OFF and you need to turn it ON:

1. Select the START NUMBER by turning the MENU DIAL
2. Press the MENU DIAL and a flashing ON will be displayed [a]
3. Press the MENU DIAL to confirm the START as ON
4. The START NUMBER will now flash [b]— indicating you can now move to the next start
5. Turn the MENU DIAL to the next START and repeat the process to turn ON/ OFF the other STARTS

Turn a Start On/Off

If the START is ON and you need to turn it OFF:

1. Select the START NUMBER by turning the MENU DIAL
2. Press the MENU DIAL once, a flashing menu box will appear around START TIME [c]
3. Turn the MENU DIAL anti-clockwise (right) and a flashing OFF will be displayed [d]
4. Press the MENU DIAL to confirm the start as OFF
5. The START NUMBER will now flash [e]—this indicates you can now move to the next START
6. Turn the MENU DIAL to the next START and repeat the process to turn ON/ OFF the other STARTS

Start Time

• START TIME is the time of day your watering begins
• Your QuikDial waters each ZONE sequentially starting from this time. ZONES are added at a later step— refer to ZONE setup instructions to learn more
• To set the watering START TIME for your active START/S:
  1. Select the START NUMBER by turning the MENU DIAL
  2. Active STARTS have the START NUMBER [a] and ON [b] displayed on the screen
  3. Press the MENU DIAL once, the menu box around START TIME will flash [c]
  4. Press the MENU DIAL again and HOURS will flash [d], indicating HOURS can now be set
  5. Turn the MENU DIAL left or right to set to your preferred HOUR for the START TIME
  6. Press the MENU DIAL again and the MINUTES will now flash [e]
  7. Turn the MENU DIAL left or right to set the MINUTES
  8. Once the MINUTES are correct, press the MENU DIAL again to move on to RUN TIME

Run Time

• RUN TIME is the watering duration for your START
• You can set 1 RUN TIME per START
• Min. RUN TIME is 1 min
• Max. RUN TIME is 99 min
• RUN TIME applies to each ZONE in the START
• As an example, if you set a RUN TIME of 60 min this will give a total of 2 hrs of watering when both ZONES are included in the START
• RUN TIME can be accessed two ways—either as a continuation from the  START TIME, or using the following steps:
  1. Turn the MENU DIAL to select the START NUMBER
  2. Press the MENU DIAL, and the menu box will flash around START TIME [a]
  3. Turn the MENU DIAL clockwise (right), and the menu box will now flash around RUN TIME [b]
  4. Press the MENU DIAL once and the RUN TIME will begin flashing [c]
  5. Turn the MENU DIAL to the desired RUN TIME (up to 99 min)
  6. Press the MENU DIAL again to move on to SET DAY

Set Day

• Your QuikDial allows you to select the days of the week to water

Warning There is no interval watering option

• The 7 days of the week are represented with their first two letters. MO for Monday, TU for Tuesday etc.
• SET DAY allows you to select (or change) the day/s you wish to water either as a continuation from the RUN TIME or using the following steps:
  1. Turn the MENU DIAL to select the START NUMBER
  2. Press the MENU DIAL
  3. The menu box will flash around START TIME [a]
  4. Turn the MENU DIAL clockwise (right), until a box is flashing around SET DAY and lines are flashing below the days of the week [b]
  5. Press the MENU DIAL once and a solid line will flash below MO only [c]
  • To keep MO selected, turn the MENU DIAL clockwise (right) to move to the next day
  • To remove MO press the MENU DIAL, MO will be removed from the screen
  6. Turn the MENU DIAL clockwise (right) to move to TU
  7. Repeat for each day, pressing the MENU DIAL to remove days as needed
  • If a day is removed by accident, turn the MENU DIAL anti-clockwise until the line is flashing under the removed day. Press the MENU DIAL again to reinstate the day
  • Only the days which are included in the program will be displayed
  8. Once you have set/removed SU all lines will flash[d]
  9. Press the MENU DIAL again to move on to ZONE

Zone

• A START will remain OFF if no ZONES are selected for the START
• ZONES can be set up either with a separate START (when needed to water on different DAYS or different START TIMES), or set up within the same START
• All STARTS have ZONE I selected by default
• You can change to another ZONE or select all ZONES via the ZONE menu
• When ZONES are set to water within the same START your QuikDial will water each zone sequentially starting from the set START TIME
• ZONE can be accessed two ways—either as a continuation from the SET DAY, or using the following steps:
  1. Turn the MENU DIAL to select the START NUMBER
  2. Press the MENU DIAL
  3. The menu box will flash around START TIME
  4. Turn the MENU DIAL  clockwise (right) until a box is flashing around ZONE [a]
  5. Press the MENU DIAL to confirm you’d like to update the ZONE menu
  6. ZONE I will flash [b]
  • Pressing the MENU DIAL once when the ZONE is flashing will allow you to select or delete the ZONE from the START
  • As ZONE I is already programmed to water during this START, you can:
    • Move onto step 7 to keep ZONE I selected
    • Press the MENU DIAL to remove ZONE I from the START
  7. Turn the MENU DIAL clockwise (right) and ZONE II [c] will flash
  • As ZONE II is not programmed to water during this START, you can:
    • Press the MENU DIAL to select ZONE II for the START
    • Wait 10 seconds to return to the default system mode and keep ZONE II deselected

Conflicting Starts

• If more than one START has been set with the same START TIME and SET DAYS, the timer will ignore the duplication. Only the first start will be run in these cases
• Use the 4 available STARTS to spread out your watering needs—avoiding conflicting STARTS

Removal of All Zones from a Start

• A START will not allow you to turn it ON until a ZONE is selected for the START
• If any active (ON) START/S have all ZONES deselected, you will need to add a ZONE back to restore the START

1. To restore the ZONE/S, turn the MENU DIAL to select the START NUMBER
2. Press the MENU DIAL
3. A box will flash around START TIME
4. Turn the dial anti-clockwise (left) until you enter ZONE selection, a box will flash around ZONE—refer to step 5 in ZONE setup instructions to continue to restore ZONES

Operation

Automatic Watering

• Ensure CLOCK, START TIME, RUN TIME, SET DAY and ZONE have all been set correctly
• Pressing the ON/OFF button during an automatic program stops it from watering
• After 10 seconds of inactivity on your QuikDial controls, the set watering schedule will be active in the background as per your confirmed settings
• In this state, your QuikDial display will cycle between the CLOCK [a] and the START TIME of your next watering session [b]

1. When the CLOCK [a] and START TIME [b] match, the ZONE/S will start watering in sequential order
2. During watering, the sprinkler animation [c] will be active and the current ZONE [d] will flash

• Additional zones scheduled for watering will also show [e]
• Your timer will have a three second period of 00 before ending a watering or moving to the next ZONE

Manual Watering

By default, the pre-set manual RUN TIME is 5 min

1. For manual (instant) watering, press ON/OFF
2. ZONE I will flash [a], turn the MENU DIAL to select a ZONE
3. Press the MENU DIAL to confirm your ZONE selection
4. To water for the pre-set manual RUN TIME, wait a short period of time for the RUN TIME to stop flashing [b], indicating it has been set
   • During watering, the sprinkler animation will be active [c] and the selected ZONE [d] will flash
5. To adjust the manual RUN TIME, turn MENU DIAL when the RUN TIME is flashing [b]
   • Min. manual RUN TIME is 1 min
   • Max. manual RUN TIME is 99 min
6. Press the MENU DIAL to confirm your selection
7. After a short period of time, the RUN TIME will stop flashing to indicate it has been set

Manual Watering

• If the RUN TIME stops flashing before you were able to adjust it—press ON/OFF to stop watering and restart the MANUAL WATERING process from step 1
• To stop watering before the remaining time has lapsed, press ON/OFF and your QuikDial will return to the default display

No/Suspended Watering Mode

1. To stop all automatic watering, press the MENU DIAL for 3 seconds
2. The display will enter NON WATERING MODE [a]
3. To return to scheduled automatic watering, press the MENU DIAL for 3 seconds
4. The NON WATERINGICON will disappear and your automated watering will continue

Maintenance

Cleaning

Info

• Check and clean your filter washer at least twice a year
• Debris can be removed with a soft toothbrush and suitable cleaner where needed (white vinegar/CLR)
• Damaged filters/washers should be replaced
• In hard water areas, further cleaning may be required after periods of no use—as minerals will set in the body of the timer

1. Remove all tap fittings and the neck assembly from the timer
2. Your timer will need to be stable and upright—an egg carton (or similar) may assist with this
3. Make a 50/50 white vinegar and water solution—pour this into the top of your timer
4. Allow it to sit for 10 min then empty the timer and rinse well
5. Turn the timer upside down and repeat this on each outlet (fill outlet with solution, allow to sit, empty and rinse well)
   • Do not immerse your timer in cleaning solution

Cold Weather

• Your QuikDial should be removed from the tap and stored away during winter
• Keep your QuikDial out of freezing conditions as this can damage internal components

Batteries

• Remove batteries from your QuikDial during periods of non-use–this will erase all settings
• Battery leakage can cause corrosion and damage to your QuikDial
• Please only use quality alkaline batteries in your tap timer
• Do not mix old and new batteries
• Do not use rechargeable batteries

Troubleshooting

Incorrect Decal

• If you have received a QuikDial with the batch number 23/36, it is likely this will have the incorrect face decal due to a printing error. This will not affect the functionality of the QuikDial, however may cause some confusion in the initial set up process
• If you have the QuikDial batch number 23/36, the face will look like the below image (highlighted in red), Zone Select should be referred too as ‘Start’
• Please refer too the below for the correct set up:

Troubleshooting

Question / Answer

• Why won’t my timer stop watering?
  • If your QuikDial Tap Timer is installed on a short run or pressure compensating system, there can be issues with the valve closing
  • This is due to more water on offer than can exit the system— creating a pressure differential
  • This can be mitigated using a pressure reducer
  • Your timer may have a blockage preventing the valve from closing– contact customer service at support@holmanindustries.com.au for assistance
• Why is there no water coming into the system?
  • Check if the filter is clogged, clean if required—refer to Cleaning for more information
  • Check for blockages in the sprinkler/ emitter, clean if required
  • There may be an airlock—remove your timer from the tap and give it a shake to displace the airlock

FAQ

• Q: How do I reset the Tap Timer?
  • A: To reset the Tap Timer, follow the resetting instructions provided in the user manual. Typically, this involves removing and reinserting the batteries and reconfiguring the settings.

More Information

Need help? Just ask!

• The Holman website has a host of additional information on features. Head to support.holmanindustries.com.au for more tips, tricks and support content.
• If you still need help, feel free to email our friendly Customer Service team at support@holmanindustries.com.au or call at 08 9416 9999.

SCAN FOR MORE INFO

Thanks for being a #SMARTGARDENER

We really appreciate having you as a customer, and would like to say thank you for choosing us.
We recommend registering your new product on our website. This will ensure we have a copy of your purchase and activate an extended warranty. Keep up to date to with relevant product information and special offers available through our newsletter.

www.holmanindustries.com.au/product- registration/

Scan

For the #SMARTGARDENER

http://www.holmanindustries.com.au/?=manual
www.holmanindustries.com.au

Copyright © 2023 Holman Industries

References

• Holman Industries
• Holman Industries - Irrigation, Garden Lights, Plumbing
• Product Registration and Extended Warranty - Holman Industries
• Product Registration and Extended Warranty - Holman Industries

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>