SENA SP149 Phantom Smart Helmet Instruction Manual

SENA SP149 Phantom Smart Helmet Instruction Manual

PHANTOM Manual

Power

Power On : Press and hold the (+) Button and Multi-function Button for 1 second
Power Off : Tap the (+) Button and Multi-function Button.

Volume Adjustment

Increase/decrease the volume : Tap the (+) Button or (-) Button.

Phone Pairing

1. Initially Pairing the Bluetooth system
   The bluetooth system will automatically enter the phone pairing mode when you initially turn on the Bluetooth system or reboot after executing Factory Reset

1. Press and hold the (+) Button and Multi-function Button for 1 second to turn on the Phantom.
2. Search for Bluetooth devices on your mobile phone. Select the Phantom in the list of the devices detected on the mobile phone.

2. Starting with your Bluetooth system powered on
   1. Press and hold the Multi-function Button for 5 seconds.
   2. Search for Bluetooth devices on your mobile phone. Select the Phantom in the list of the devices detected on the mobile phone.

Music Operation

Play or pause music: Press and hold the Multi-function Button for 1 second.
Track back: Press and hold the (-) Button for 1 second.
Track forward: Press and hold the (+) Button for 1 second.

Mobile Phone Call Making and Answering

Answering a call: Tap the Multi-function Button
Ending a call : Press and hold the Multi-function Button for 2 seconds.
Rejecting a call : Press and hold the Multi-function Button for 2 seconds.
Call a voice assistant : Press and hold the Multi-function Button for 2 seconds.

Mesh Intercom

Mesh Intercom On/Off : Tap the Mesh Intercom Button

ANC Mode

ANC Mode On/Off : Tap the ANC Button.

LED LIGHT

Flashlight On/Off : Tap the Flashlight Button.
Taillight On/Off : Tap the Tallight Button.

Setting

Enter the Configuration Menu: Press and hold the Multi-function Button for 10 seconds.

Troubleshooting

Factory Reset

If you want to restore the bluetooth system to factory default settings, use the Factory Reset in the configuration menu.

1. Press the hold the Multi-function Button for 10 seconds.
2. Double tap the (-) Button.
3. Tap the Multi-function Button.
   The bluetooth system automatically restores the default settings and turns off.

Fault Reset

When the bluetooth system is not working properly, you can easily reset the unit:

1. Locate the pinhole reset button next to the Power Charging & Firmware Upgrade Port.

2. Gently insert a paperclip into the hole and tap the Pin-hole Fault Reset Button with light pressure.

3. The bluetooth system will shut down.

Certification and Safety Approvals FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antennae
-Increase the separation between the equipment and the receiver
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –
Consult the dealer or an experienced radio/TV technician for help.

FCC RF Exposure Statement
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment.
End users must follow the specific operating instructions for satisfying RF exposure compliance.
When equipped, the distance between antenna and one’s head surface is 35.8mm.

FCC Caution
Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment.

Industry Canada(IC) Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1)this device may not cause interference, and
(2)this device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>