HUSKY 8HOTC8409BB1M 9 Drawer Mobile Workbench User Guide
- August 20, 2024
- Husky
Table of Contents
HUSKY 8HOTC8409BB1M 9 Drawer Mobile Workbench User Guide
Safety Information
- Do not open more than one drawer at a time.
- Do not let children approach the product.
- To help prevent the product from tipping, load the product starting with the bottom drawers.
- Keep locking the casters’ brake set unless you are moving the cabinet. This will help to prevent the product from rolling.
- Lock all drawers before moving the product.
- Make sure all drawers close tightly before locking/unlocking.
- Do not step in any drawer/drawers.
- When moving this product, push it rather than pull it.
- Do not alter this product in any manner.
- Do not use the hand to unlock the caster.
Plug and Outlet Safety
WARNING: Chest/cabinet plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earth (grounded) chest/cabinet power strips. Unmodified plugs and matching outlets will reduce risk of electric shock.
WARNING: Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is increased risk of electric shock if your body is earthed or grounded.
WARNING: Chests/cabinets marked “Grounding Required” have a power strip
with a three wire cord and three prong grounding plug. The plug must be
connected to a properly grounded outlet (See Figure).
If the power strip should electrically malfunction or break down, grounding
provides a low resistance path to carry electricity away from the user,
reducing the risk of electric shock. The grounding prong in the plug is
connected through the green wire inside the cord to the grounding system in
the power strip. The green wire in the cord must be the only wire connected to
the power strip’s grounding system and must never be attached to an
electrically “live” terminal. Your power strip must be plugged into an
appropriate outlet, properly installed and grounded in accordance with all
codes and ordinances.
DANGER: Do not stand on this product. You may fall or cause the product to tip.
DANGER: Do not move the product prior to closing and locking all the drawers. The drawers could come open and make the product unstable and tip.
DANGER: Do not mount this product on a truck bed or any other moving object.
WARNING: Keep the product on a level surface. The product may become unstable and tip if stored or moved on an uneven surface.
CAUTION: Do not lift this product directly with a forklift or tow with any mechanical devices.
CAUTION: Do not exceed the maximum product weight, including contents. Do
not exceed the maximum weight for each drawer.
See Specifications on page 4.
CAUTION: Only transport this product when empty. Properly secure when transporting.
Safety Information (continued)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION: Do not use the side handle as a point of leverage to lift the
unit off of the ground. Handle is not intended to withstand the force of
vertical lifting, and is only designed to aid in the movement of unit around
on casters.
Failure to adhere to this warning may cause handle to break and cause personal
injury and/or product damage.
The Responsible party information:
Clearwater Metal Vn JSC Lot CN2, Mai Trung IZ, An Tay Village, Ben Cat Town,
Binh Duong Province, Vietnam. Tel: +84.274.3581.773 Product name: Power strip
6 outlets with 2 USB ports and 1 type C Model# K2415014C / K24150251C
Warranty
The manufacturer warrants the product to be free from defects in materials and
workmanship for a period of five (5) years from date of purchase.
This warranty applies only to the original consumer and only to products used
in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or
replacement of the product at the manufacturer’s discretion, provided that the
product has not been damaged through misuse, abuse, accident, modifications,
alteration neglect or mishandling. This warranty shall not apply to any
product that is found to have been improperly installed, set-up, or used in
any way not in accordance with the instructions supplied with the product.
This warranty shall not apply to a failure of the product as a result of an
accident, misuse, abuse, negligence, alteration, faulty installation, or any
other failure not relating to faulty material or workmanship. This warranty
shall not apply to the finish on any portion of the products such as surface
and/or weathering, as this is considered normal wear and tear.
The manufacturer does not warrant and specifically disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product.
Contact the Customer Service Team at 1-888-HD-HUSKY or visit www.huskytools.com.
Pre-assembly
TOOLS REQUIRED
Phillips screwdriver
Safety goggles
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
**AA
BB
CC
**
| Part | Part Code | Description | Quantity |
|---|---|---|---|
| AA | L034532A | Bolt M4 x 10L | 8 |
| BB | L0345001 | Bolt M6 x 15L | 4 |
| CC | L3011002 | 10MM/13MM Wrench | 1 |
SPECIFICATIONS
| Maximum capacity (drawer) | 100 lbs |
|---|---|
| Maximum capacity (bottom deep drawers) | 200 lbs |
| Maximum capacity (total unit) | 3,800 lbs |
NOTE: Begin product assembly close to the final intended location of your mobile workbench. This product is heavy and may be difficult to move after assembly
Pre-assembly (continued)
PACKAGE CONTENTS
| Part | Description | Quantity |
|---|---|---|
| A | Stainless steel top | 1 |
| B | Side handle | 1 |
| C | Rolling cabinet | 1 |
| D | Swivel caster with brake | 4 |
| E | Soft Close Drawer slide (pair | 9 |
| F | Drawer | 9 |
| G | Swivel caster | 2 |
| H | Power strip bracket | 2 |
| Part | Description | Quantity |
| --- | --- | --- |
| I | Key (set) | 1 |
| J | Lock | 1 |
| K | Drawer liner | 9 |
| L | Drawer slide (pair) | 3 |
| M | Power strip | 2 |
| N | Grommet | 2 |
| O | Shelf | 1 |
| P | Shelf clips | 4 |
Assembly
Attaching the side handle
- Attach the side handle (B) to the cabinet using four bolts (BB).
- Tighten all bolts with the 10 mm wrench (CC).
Do not over tighten the bolts to avoid damage to the finish.
NOTE: The holes in the cabinet are tapped and do not require nuts.
Attaching the power strip brackets
- Attach the power strip brackets (H) to the cabinet for both sides using two bolts (AA) each.
- Tighten all bolts using a screwdriver.
Do not over tighten the bolts to avoid damage to the finish.
NOTE: The holes in the cabinet are tapped and do not require nuts.
Installing the drawer liners
- Place the drawer liners (K) in appropriately-sized drawers to protect the surface.
Installing the shelf brackets and shelf
- Install the four shelf brackets (P) inside the storage area at the desired shelf height location.
- Ensure all shelf brackets are aligned horizontally and are properly seated in the bracket slots.
- O Install the shelf (O) inside the storage area so that it sits on top of the four shelf brackets (P) flush and level.
Operation
Locking and unlocking the unit
IMPORTANT: The drawers must be fully closed before locking / unlocking the unit.
- To lock the unit, insert the key (I) into the lock (J) and turn
- To unlock the unit, insert the key (I) into the lock (J) and it one quarter turn counterclockwise. Then remove the key.
turn it one quarter turn clockwise. Then remove the key.
Removing the drawers
- Fully extend and empty the drawer. 2
- On the slide, lift up the plastic release lever on one slide and push down the plastic release lever on the other slide.
Gently pull the drawer out so the slides can ride over the stops.
Installing the drawers
- Pull the slides and slide carrier out until fully extended.
- Hold the slide on the cabinet while aligning it with the slide on the drawer.
- Slightly insert one side and repeat for the other side.
- Slowly push the drawer until it is fully closed to engage the slide.
- Open the drawer and close it to verify proper operation.
Maintenance
Maintaining the casters
- Grease the casters annually using high quality bearing grease.
Maintaining the drawers
- Periodically clean the drawer trim and inside the drawers with a mild detergent and water.
- Remove grease and oil with a standard, nonflammable cleaning fluid.
- The use of drawer liners is recommended to protect the finish inside the drawers and make the drawers easier to clean. Drawer liners can be purchased at The Home Depot.
- Lubricate the slides semi-annually with grease or equivalent.
Care and Cleaning
- This steel product has been coated with industrial powder coating for a durable finish. To help protect this finish, do not allow harsh chemicals ® such as oil or grease to remain on the powder coating surface. Use a glass cleaner ( Windex or equivalent product) to clean and maintain all powder coated surfaces.
Service Parts
| Part | Part Code | Description | Quantity |
|---|---|---|---|
| A | DTC61005 | Stainless Steel Top | 1 |
| B | DTC040019 | Side Handle | 1 |
| D | K03220373 | Swivel caster with brake | 4 |
| E | K0203036 | Soft Close Drawer slide (pair) | 9 |
| G | K03220374 | Swivel caster | 2 |
| H | DTC50001 | Power strip bracket | 4 |
| I+J | K0612012 | Key (set) + Lock | 1 |
| Part | Part Code | Description | Quantity |
| --- | --- | --- | --- |
| K | K0129161 | Drawer liner | 1 |
| L | DTC35037 | Drawer slide (pair) | 3 |
| M | K2415014C | Power strip | 2 |
| N | L2065001 | Grommet | 2 |
| O | D390121 | Shelf | 1 |
| P | Z7400022I | Shelf Clips | 4 |
Questions, problems, missing parts? Before returning to the store, call Husky Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m. EST Saturday
1-888-HD-HUSKY
HUSKYTOOLS.COM
Retain this manual for future use.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>