Godox AD600ProII All in One Outdoor Flash Instruction Manual

Godox AD600ProII All-in-One Outdoor Flash

Product Specifications:

• Model : All-in-One Outdoor Flash
• Wireless System : 2.4G
• Compatibility : Canon, Nikon, Sony, Olympus, Panasonic, Fujifilm, Pentax, Leica, etc.
• Transmission Distance : Up to 100m

Product Usage Instructions

Wireless Settings:
To adjust wireless settings, follow these steps:

1. Press the MENU button to enter the menu interface.
2. Turn the select dial to navigate and press the SET button to choose among wireless/channel/group/ID/wireless sync.
3. Adjust the parameters by turning the select dial and pressing the SET button.
4. Press the MENU button to return to the previous menu or press again to return to the main interface.

Wireless Flash Shooting:
For wireless flash shooting, follow these guidelines:

• Ensure the transmitter and receiver units are properly paired.
• The transmission distance for wireless flash shooting is approximately 100m.
• Perform test flashes before actual shooting to ensure proper operation.
• Consider environmental factors that may affect transmission distance.
• Divide receiver units into groups for TTL auto flash with different flash ratios and modes.

Important Safety Instructions

• This product is professional photographic equipment, to be operated by professional personnel only.
• The following basic safety precautions must be followed when using this product:
• All transport protective materials and packaging on the product must be removed before use.

1. Carefully read and fully understand the instruction manual before use and strictly follow the safety instructions. Failure to do so may result in death, serious injury, damage to the product, or other property damage.

2. High voltage exists when the flash is powered on. Internal capacitors will remain charged for some time after power off.

3. This product is a professional lighting fixture, children are prohibited from using it. Children must be closely supervised by adults when approaching the fixture, to prevent collisions with the fixture or unauthorized use that could cause personal injury.

4. This is not an ordinary lighting fixture and must not be used for general illumination. Anyone with a history of eye damage or sensitivity should avoid using this fixture or looking directly at it.

5. Extreme caution must be exercised when using it, do not touch high-temperature parts such as flash tubes to avoid burns.

6. Do not point the flash directly at the eyes (especially baby’s eyes) under any circumstances, as this could impair vision in a short time. Turn off immediately if discomfort occurs, stop using, and seek medical attention promptly.

7. If the flash tube is damaged, stop using it immediately and contact the manufacturer, service agent, or qualified repair personnel for a replacement to prevent accidents.

8. Dot not use damaged equipment or accessories. Allow professional repair technicians to inspect and confirm normal operation before continuing use after repairs.

9. Disconnect power source or remove batteries (if it has one) before replacing flash tube, protective glass, or fuses. Allow l O minutes to cool before replacing the flash tube, and wear insulated or heat-resistant gloves when operating.

10. Turn off power before connecting or disconnecting plugs from outlets. Ensure plugs are fully inserted when connecting.

11. Stop using immediately if the product shell is cracked due to falling, squeezing, or strong impact, to avoid touching the internal electronic components and getting an electric shock.

12. Some products have long power cords, please place them properly to avoid contact with heat sources or tripping others. It is recommended to use the original power cord. Damage caused by non-original cords is not covered by the warranty.

13. Unplug the equipment power plug from the power socket before cleaning or maintenance. Do not pull the power cord forcibly, use both hands to hold the plug end and pull it out.

14. This device is not waterproof. Keep it dry and avoid immersing it in water or other liquids. It should be installed in a ventilated and dry location and avoid using in rainy, humid, dusty, or overheated environments. Do not place items above the device or allow liquids to flow into it to prevent danger.

15. Do not disassemble without authorization. If the product malfunctions, it must be inspected and repaired by our company or authorized repair personnel.

16. Before storing the device, ensure it has completely cooled down and the power cord is unplugged, then put it in the protective case or a ventilated dry location.

17. Do not place the device near alcohol, gasoline, or other flammable volatile solvents or gases such as methane and ethane.

18. Do not use or store this device in potentially explosive environments.

19. Do not cover the heat dissipation port!

20. Do not use accessories not been approved by our company, as this may cause fire, electric shock or personal injury.

21. Clean gently with a dry cloth. Do not use a wet cloth as it may damage the device.

22. Some products are equipped with protective covers that must be removed before use.

23. This instruction manual is based on rigorous testing. Changes in design and specifications are subject to change without notice. Check official website for latest instruction manual and product updates.

24. Use only specified charger and follow proper usage instructions for certain products with built-in lithium batteries, within the rated voltage and temperature range.

25. Some products are powered by lithium batteries, who have limited lifespans and will gradually lose their charging capacities, which is irreversible. As the battery ages, the product’s battery life will decrease. The lifespan of lithium battery is estimated to be 2 to 3 years. Please regularly check the battery, and if the charging time significantly increases or the battery life significantly decreases, consider replacing the battery.

26. Some products are equipped with lithium batteries. The following are the storage recommendations: Charge the battery to about 50% before storage. Charge it to about 50%
    at least every six months. Removable batteries should be stored separately. The storage temperature should be between 0°C and 40°C.

27. Some products are powered by lithium batteries.
    Please note:

    • Do not disassemble, crush, or puncture the battery;
    • Avoid short-circuiting the battery contacts;
    • Do not expose the battery to fire or water;
    • Do not expose the battery to temperatures above 60°C;
    • Keep out of reach of children;
    • Protect the battery from excessive shock or vibration;
    • Do not use a damaged battery;
    • If the battery leaks, avoid contact with the leaking fluid;
    • If the battery fluid comes into contact with your eyes, immediately rinse with water for at least 15 minutes. Lift your eyelids until there are no signs of fluid and seek medical attention promptly.

28. Confirm and comply with all relevant local laws and regulations when handling any batteries.

29. The warranty period for this device as a whole is one year. Consumables (such as batteries), adapters, power cords, and other accessories are not covered by the warranty.

30. Unauthorized repairs will void the warranty and will incur charges.

31. Failures from improper operation is not covered under warranty.

Foreword
Thank you for purchasing! AD600ProII has strong power, an all-in-one lithium battery pack and great portability. When using Godox 2.4G wireless X system, it can be triggered by XPro/XProII/X2T/X3 series flash trigger in M/Multi/TTL mode. With transmitter & receiver functions, AD600ProII can also use in combination with Godox camera flashes, outdoor flashes, studio flashes, etc. With this flash, your shooting will become simpler. With high-speed shooting throughout the process, single fixture overshadowing the sunlight, bare flash tube and reflector make a perfect match for outdoor and live shooting, AD600ProII is an ideal light source for freelance commercial photographers, journalists, photography enthusiasts, wedding documentary photographers, etc.

Main Features

• Quick Recycle Time : 0.01s~0.9s (max. power).
• Stable Color Temperature: shift around ±100K over the entire power range with this function.
• LED Modeling Lamp: 40W*40W bi-color large LED modeling light freely adjusts brightness and CCT.
• Studio Quality Light: up to 600Ws, GN 87 (m ISO 100, with efficient reflector), 360 full power flashes, 1/8000s high-speed sync.
• Precise Power Adjustment : from full power 1/1 to 1/512 with 0.1 increment each step.
• Wide Compatibility: fully support M, Multi and wireless TTL flash systems of Canon, Nikon, Fujifilm, Olympus, Sony, Leica, Pentax, etc. Workable as a receiver unit in a wireless flash group.
• Wireless Control: with built-in 2.4G wireless X system to achieve remote control by optional Godox flash triggers, and 3.5mm sync cord jack to achieve various sync triggering modes.
• Distinct Group Colors : 16 groups with different colors to quickly distinguish even in remote distance usage.
• Simple Operation: 2.8″ color screen together with steplessly rotatable select dial, detachable battery pack design.
• Wide-range Accessories : Bowens mount has wide compatibility and versatility.

Warning

• Always keep this product dry.
• Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center.
• Stop using this product if it breaks open due to extrusion, falling or a strong hit. Otherwise, electric shock may occur if you touch the electronic parts inside it.
• Do not leave or store the flash unit if the ambient temperature reads over 50°C.
• Do not fire the flash directly into the eyes (especially those of babies) within short distances. Otherwise, visual impairment may occur.
• Do not use the flash unit in the presence of flammable gases, chemicals and other similar materials. In certain circumstances, these materials may be sensitive to the strong light emitting from this flash unit and fire or electromagnetic interference may result.
• This product is not waterproof, do not use in rain or in damp conditions.
• Please remove the flash head protection cover before using it.

CAUTION

• Hot surface.
• Do not touch.
• Burned fingers when handling the parts.
• Wait one-half hour after switching off before handling parts.

Name of Parts

Flash Body

1. Flash Tube
2. Color Screen
3. MENU Button
4. MODE Button
5. Select Dial
6. SET Button
7. Power Switch/Test Button
8. Modeling Lamp Button
9. Bracket Locking Knob
10. Handle Fixing Fastener
11. Handle
12. Accessory Locking Pusher
13. USB-C Port
14. 3.5mm Sync Cord Jack
15. Group Indicator x2
16. Photocell Receiver
17. Battery Indicator Button
18. Battery Charging Port
19. Battery Level Indicator
20. Battery Compartment Pusher
21. Reflector

What’s Inside

Separately Sold Accessories

• Flash Head: H600P Portable Flash Head.
• Power Supply AC26 Power Source,UC46 USB Charger.
• Flash Trigger XPro, XProl I, X2T, X3 series.
• Optical Accessories: Umbrella Softbox,Collapsible Lantern Softbox, Quick-loading Parabolic Softbox, Beauty Dish, Umbrella Diffuser, Snoot, Light Stand, etc.

Installing and Disassembling Reflector/Flash Tube

Installing the Reflector : Insert the reflector into the accessory mount , press and hold then rotate clockwise, the accessory locking pusher will lock up.

Disassembling the Reflector : Press down the accessory locking pusher, rotate the reflector anticlockwise to unlock.

Installing the Flash Tube : Press down the accessory locking pusher, remove the reflector or other accessories. Match the flash tube in the tube socket and push until it is securely seated into the socket.

Disassembling the Flash Tube : Press down the accessory locking pusher, remove the reflector or other accessories. Grasp the flash tube and pull it out horizontally.

Note : Please wear gloves for the above operations.

Adjusting Flash Angle

1. When the handle fixing fastener is not pulled out, rotate the handle anticlockwise to unlock it, adjust the flash body for the desired angle, then rotate the handle clockwise to tighten.
2. If the handle collides the flash body in rotation, please press the handle fixing fastener and pull out the handle, repeat the step 1 after stretching out a few distance.

Power Switch

1. Long press the power switch button until the unlock icon < > is displayed on the panel, then rotate the select dial clockwise to turn on the device.
2. Long press the power switch button for until panel black out to turn off the device.

Note : Turn off the device if it will not be used for an extended period. This device is designed with an automatic power off function, which can be set in menu settings.

Color Screen

Battery

Features

1. This flash unit uses lithium battery which has long runtime. The available charge-and-discharge times are 300.
2. It is reliably safe. The inner circuit is against overcharge, overdischarge, overcurrent, and short circuit.
3. It takes only 2 hours to fully charge the battery by using the standard battery charger.

Cautions

• Do not short circuit.
• Do not expose to rain or immerse into water. This battery is not water proof.
• Keep out of reach of children.
• No over 24 hours’ continuous charging.
• Store in dry, cool, ventilated places.
• Do not put aside or into fire.
• Dead batteries should be disposed according to local regulations.
• If the battery had ceased using for over 3 months, please make a full recharge.

Loading and Unloading the Battery

1. Loading : Match the battery’s groove with the main battery compartment’s ridge. Push down the battery pack until it is locked.
2. Unloading : Push the battery compartment pusher and the battery pack upward at the same time to unload it.

Battery Level Indication
Attach the battery pack to the flash correctly. Check the battery level by pressing the battery indicator button and lightening the battery level indicator as the following table shows.

LED Battery Level Indication on the Battery

(Indicating battery level and management

of non-loaded battery)

| Meaning/Percentage of Battery Level
---|---
1 red grid +3 green grids| 75% ～ 100%
1 red grid +2 green grids| 50% ～ 75%
1 red grid +1 green grid| 25% ～ 50%
1 red grid| 3% ～ 25%
2% flash red, 1% off| ＜ 2%

The battery level is going to be used out immediately. And the flash will alarm for 1 minute and auto power off in 3 minutes.

Note: Please recharge the battery as soon as possible (within 10 days). Then, the battery can be used or be placed for long

period.

Note : The indications are almost the same except for the grids shift.

Battery Activation Instructions
Due to the battery upgrade, if you haven’t used the battery for more than a month, it will automatically go to sleep. please try to activate it if you use or charge again after a month.

Activation method: Short press the battery indicator button to activate

High-Speed Sync
High-speed sync (FP flash) enables the flash to synchronize with all camera shutter speeds. This is convenient when you want to use aperture priority for fill-flash portraits.

1.  Press the MENU button to enter menu interface, turn the select dial and press the SET button to enter high speed sync and turn on it. Then press MENU button to return to the main interface, the HSS icon can be seen on the panel.

2. Please use Xl /XProl /XProll /X2T /X3 series flash triggers.
   Note:

   • If you set a shutter speed that is the same as or slower than the camera’s maximum flash sync speed, will not be displayed in the viewfinder.
   • With high-speed sync, the faster the shutter speed, the shorter the effective flash range.
   • To return to normal flash, turn off the high-speed sync function in menu settings. Then  will disappear.
   • Multi flash mode cannot be set in high-speed sync mode.
   • Over-temperature protection may be activated after 100 consecutive high-speed sync flashes.

M: Manual Flash
The flash output is adjustable from 1 /1 full power to 1/512 power with 0.1 step increment. To obtain a correct flash exposure, use a hand-held flash meter to determine the required flash output.
Press MODE button so that< M > is displayed. Turn the select dial to choose a desired flash output amount.

Flash Output Range

• The following table makes it easier to see how the step changes in terms of aperture value when you increase or decrease the flash output.
• Turn the select dial clockwise to increase the flash output, while turn it anticlockwise to decrease the flash output.

Optical S1 Secondary Unit Setting
Press MENU button to enter photocell and choose S1 function, so that this flash can function as an optical S1 secondary flash with optical sensor in M manual flash mode. Then press then MENU button to return to the main interface. With this function, the flash will fire synchronously when the main flash fires, the same effect as that by the use of wireless triggers. This helps create multiple lighting effects.

Optical S2 Secondary Unit Setting
Press MENU button to enter photocell and choose S2 function, so that this flash can also function as an optical S2 secondary flash with optical sensor in M manual flash mode. Then press then MENU button to return to the main interface. This is useful when cameras have pre-flash function. With this function, the flash will ignore a single “preflash” from the main flash and will only fire in response to the second, actual flash from the main unit.

Note : S1 and S2 optical triggering is only available in M manual flash mode.

Display Flash Duration
Flash duration refers to the length of time that from flash’s firing to reach the half peak at maximum. The half peak at maximum is usually expressed as t=0.5. In order to provide the photographer with more concrete data, this product adopts t=O.l. The difference between t=0.5 and t=O.l is shown in the following picture.

Note : Turn off the high speed sync function in M mode, the flash duration will then be displayed.

Multi: Stroboscopic Flash
With stroboscopic flash, a rapid series of flashes is fired. It can be used to capture multiple images of a moving subject in a single photograph. You can set the flash output, number of flashes, and flash frequency (number of flashes per sec. expressed as Hz).

1. Press the MODE button so that < Multi >  is displayed, turn the select dial to choose a desired flash output.
2. Press the SET button and turn the select dial to set the number of flashes.
3. Press the SET button and turn the select dial to set the flash frequency.

Calculating the Shutter Speed

• During stroboscopic flash, the shutter remains open until the firing stops. Use the formula below to calculate the shutter speed and set it with the camera.
• Number of Flashes / Flash Frequency = Shutter Speed
• For example, if the number of flashes is 10 and the firing frequency is 5 Hz, the shutter speed should be at least 2 seconds.

Note:

• Stroboscopic flash is most effective with a highly reflective subject against a dark background.
• Using a tripod and a TTL flash trigger is recommended.
• A flash output of 1 /1 and 1 /2 cannot be set for stroboscopic flash.
• Stroboscopic flash can be used with “bulb”.
• If the number of flashes is displayed as “–“, the firing will continue until the shutter closes or the battery is exhausted. The number of flashes will be limited as shown by the following table.

Maximum Stroboscopic Flashes:

TTL Auto Flash

• In TTL mode, the camera’s metering system detects the flash reflected from the subject and automatically adjusts the flash output so that the subject and background are evenly exposed.
• Press the MENU button to enter menu interface, turn the select dial and press the SIT button to enter wireless and turn on it, set the group among A to E. Press the MENU button to return to the main interface.
• Press MODE button to enter TTL mode, the screen will display< TTL>.

Wireless (2.4G) Transmission

• AD600ProII adopts 2.4G wireless X system, which has good compatibility with other Godox products. It can automatically switch to receiver unit according to the transmitter unit instead
  of setting manually. The compatible cameras include Canon, Nikon, Sony, Olympus, Panasonic, Fujifilm, Pentax, Leica, etc.

• As a receiver unit, AD600ProII can be controlled by the following transmitter units: XPROII series/X3 series /X2T series /V1Pro series /V1 series /V860III series.

Wireless Settings

• Press the MENU button to enter menu interface, turn the select dial and press the SET button to choose among wireless/channel/group/ID/wireless sync, then turn the select dial and press the SET button to adjust the parameters.
• Press the MENU button to return to the previous menu, press again to return to the main interface.

Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the channel to prevent signal interference. The channels of the transmitter unit and the receiver unit(s) must be set to the same.

Take X3 flash trigger as an example:

1. Turn off the camera and mount the flash trigger on camera hot shoe. Then, power on the flash trigger and the camera.
2. Slide the screen of X3 down from the top to display , press to enter C.Fn. menu, then press to set CH and ID. Slide the screen from the left to the right to return to the main interface, on which you can set the flash mode and output power level of groups.
3. Press the MENU button of AD600Proll to select wireless and turn it on, then set the CH and ID the same to the flash trigger.
4. Press the wireless sync on the trigger and flash, then press the SET button on the flash can set their CH and ID to the same.
5. Press the camera shutter to trigger.

Wireless Flash Shooting
Positioning and Operation Range (Example of wireless flash shooting)

Auto flash shooting with one receiver unit

Note:

1. Please use the transmitter unit with wireless transmission function.
2. Before shooting, perform a test flash and test shooting.
3. The transmission distance might be shorter depending on the conditions such as positioning of receiver units, the surrounding environment and weather conditions.
4. The receiver unit can be turned off on the transmitter unit.

Wireless Multiple Flash Shooting
You can divide the receiver units into two or three groups and perform TTL auto flash while changing the flash ratio (factor). In addition, you can set and shoot with a different flash mode for each firing group.

• Auto flash shooting with two receiver units
• Auto flash shooting with three receiver units

Flash Mode
Press the MENU button to enter menu interface, turn the select dial and press the SET button to enter flash mode, in which you can choose among normal, color and freeze.

group indicator will

blink and the beeper will beep for 1min if it has been turned on, please press the test button to resume to normal use. The stable color temperature function is only available in non-HSS M mode, and value of which will shift around ±100K over the entire power range

Freeze| Freeze mode, with< ®>on the main interface. The flash duration is shorter than the normal flash mode, and the power is also less than the normal flash mode. The freeze mode

is only available in M mode and Multi mode.

The Reason & Solution of Not Triggering in Godox 2.4G Wireless

1. Disturbed by the 2.4G signal in outer environment (e.g. wireless base station, 2.4G wifi router, Bluetooth, etc.)
   To adjust the channel CH setting on the flash trigger (add l 0+ channels) and use the channel which is not disturbed. Or turn off the other 2.4G equipment in working.

2. Please make sure that whether the flash has finished its recycle or caught up with the continuous shooting speed or not {the flash ready indicator is lightened) and the flash is not under the state of over-heat protection or other abnormal situation.
   Please downgrade the flash power output. If the flash is in TTL mode, please try to change it to M mode.

3. Whether the distance between the flash trigger and the flash is too close or not ( < 0.5m).

   • Please turn on “short distance wireless mode” of the flash trigger.
   • Xl Series: Press and hold the triggering button then turn on the device, until the indicator blinks twice.
   • XPro and X2T Series : Please set the C.Fn-DIST to 0-30m.
   • X3 Series: Please set the triggering distance to 0-30m.

4. Whether the flash is in the low battery states or not.
   Please charge or replace the battery in time, and ensure both devices have enough battery power.

Modeling Lamp
AD600ProII is equipped with 40W*40W bi-color LED modeling lamp. Press the modeling lamp button to enter modeling lamp settings, turn the select dial to choose among off/free/prop, then turn the select dial and press the SET button to adjust the parameters. Press the modeling lamp button to return to the main interface.

OFF| Brightness ( in 1% increment )| CCT ( in 100K increment )
---|---|---
FREE| 10%-100%| 2800K-6000K
PROP| Brightness follows flash power| 2800K-6000K

C.Fn: Setting Custom Functions
Press the MENU button to enter menu interface, turn the select dial and press the SET button to choose among the following functions, then turn the select dial and press the SET button to adjust its parameters. Press the MENU button to return to the previous interface, press again to return to the main interface.

S2
| HSS| Off| Turn off high speed sync
On| Turn on high speed sync in M mode
| Model| Inter| Modeling lamp off in triggering
Cont| Modeling lamp constant on
| Beep| Off| Beep is off
On| Beep is on
| Type| 1/512| Flash step displays as 1/512 -1/1
1.0| Flash step displays as 1.0 -10.0 in non-HSS mode
| Standby| 30sec| Screen blacks out in 30sec of idle use
lmin| Screen blacks out in 1min of idle use
2min| Screen blacks out in 2min of idle use
3min| Screen blacks out in 3min of idle use
| Auto Off| Off| Turn off auto off function
30min| Auto off in 30min
60min| Auto off in 60min
90min| Auto off in 90min
120min| Auto off in 120min
| Brightness| 20%-100%| Turn the select dial to adjust
| Delay| Off| Turn off delay flash
0.Qls-30.0s| Turn the select dial to adjust in 0.01s increment
| Mask| 2Mask| Turn the select dial to adjust
3Alt
4Alt
| Language| Chinese| Simplified Chinese operating system
---|---|---|---
English| English operating system
| Reset| Yes| Factory reset
No| Cancel factory reset
| Device Info|  | Display the current model and version

Sync Triggering
The sync cord jack is a Φ3.5mm plug. Insert a trigger plug in and the flash will be fired synchronously with the camera shutter.

Protection Function

Over-Temperature Protection

• To avoid overheating and deteriorating the flash head, do not fire more than 100 continuous flashes in fast succession at 1/1 full power. After 100 continuous flashes, allow a rest time of at least 10 minutes.
• If you fire more than 100 continuous flashes and then fire more flashes in short intervals, the inner over-temperature protection function may be activated and make the recycling time over 10 seconds. If this occurs, allow a rest time of about 10 minutes, and the flash unit will then return to normal.
• When the over-temperature protection is started, < thermameter > is shown on the screen.

Number of flashes that will activate over-temperature protection:

Number of flashes that will activate over-temperature protection in high- speed sync triggering mode:

1/64(+0.0 ~ +0.9)
1/128(+0.0 ~ +0.9)| 210
1/256(+0.0 ~ +0.9)

Other Protections
The system provides real-time protection to secure the device and your safety. The following lists prompts for your reference:

Display|
---|---
Error| A failure occurs on the recycling system so that the flash cannot fire. Please restart the
flash unit. If the problem still exists, please send this product to a maintenance center.
Error3| The voltage on two outlets of the flash tube is too high. Please send this product to a
maintenance center
Error9| There are some errors occurred during the upgrading process. Please using the correct
firmware upgrade method.

Technical Data

(compatible with Canon E-TTL II, Nikon i-TTL, Sony, Olympus, Panasonic,

Fujifilm)

Flash Mode| Wireless off: M/Multi
Wireless receiver mode:TTL/M/Multi
Guide No. (1/1 step)| 87(ISO 100,in meters,with efficient reflector)

Flash Duration

| Normal: 1/220s ～ 1/11760s
Color: 1/220s ～ 1/7400s
Freeze:1/2570s ～ 1/20400s
Power (1/1 step)| 600Ws
Power Output| 10 steps:1/512 ～ 1/1(with 0.1 increment each step)
Stroboscopic Flash

FEC

| Provided (up to 100 times, 100Hz)

Manual, FEB

Sync Mode| High-speed sync (up to 1/8000 seconds), first-curtain sync, and second-

curtain sync

Delay Flash| 0.01 ～ 30s
Mask| √
Fan| √
Beep| √
Flash Duration Indication| √
Modeling Lamp (LED)| √
Photocell| S1/S2/OFF
Display| Color screen
Wireless Flash (2.4G transmission)
Wireless Function| Receiver, Off
Controllable Receiver Groups| 16: 0-9, A-F
Transmission Range| Approx. 100m
Channels| 32:1-32
ID| 01-99/OFF
Power Supply
Power Supply| Lithium battery(28.8V/2600mAh)
Full Power Flashes| 360
Recycle Time| Approx. 0.01s ～ 0.9s
Battery Level Indicator| √
Power Saving| Auto off function is available in menu settings (30min to 120min of idle use)
Sync Triggering Mode| 3.5mm sync cord
Flash Tube Color Temperature| 5800±200K
Dimensions
Dimension (with battery, flash tube and reflector)| ≈12.99″7.87″4.92″
Net Weight (with battery, flash

tube and reflector)

| ≈3.5kg

Specifications and data may subject to changes without notice.

Firmware Upgrade

• This flash supports firmware upgrade through the USB-C port. Update information will be released on our official website.
• Please use an USB-C cable (sold separately) for firmware upgrade.
• As the firmware upgrade needs the support of Godox G3 software, please download and install the ‘Godox G3 firmware upgrade software· from Godox official website before upgrading. Then, choose the related firmware file.
• Please refer to the latest electronic version of the instruction manual.

Maintenance

• Shut down the device immediately should abnormal operation be detected.
• Avoid sudden impacts and the product should be dedusted regularly.
• It is normal for the flash tube to be warm when in use. Avoid continuous flashes if unnecessary.
• Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories.
• This product, except consumables e.g. flash tube, is supported with a one-year warranty.
• Unauthorized service will void the warranty.
• If the product had failures or was wetted, do not use it until it is repaired by professionals.
• Changes made to the specifications or designs may not be reflected in this manual.

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it. Thank you!

Note : This form shall be sealed by the seller.

Applicable Products
Applicable ProductsThe document applies to the products listed on the Product Maintenance Information (see below for further information). Other products or accessories (e.g. promotional items, giveaways additional accessories attached, etc.) are not included in this warranty scope.

Warranty Period
The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day(purchase date) when the product is bought for the first time, And the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide a valid warranty card. If you cannot provide a valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Inapplicable Cases
The guarantee and service offered by this document are not applicable in the following cases:

1. The product or accessory has expired its warranty period;
2. Breakage or damage caused by inappropriate usage, maintenance, or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by an external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding, and damp environments, etc;
3. Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alteration, addition and detachment;
4. The original identifying information of the product or accessory is modified  alternated, or removed;
5. No valid warranty card;
6. Breakage or damage caused by using illegally authorized, nonstandard, or non-public released software;
7. Breakage or damage caused by force majeure or accident;
8. Breakage or damage that could not be attributed to the product itself.

Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope.

Maintenance and Service Support Information
The warranty period and service types of products are implemented according to the following Product Maintenance Information:

FAQ

Q: What cameras are compatible with the All-in-One Outdoor Flash?
A: The flash is compatible with Canon, Nikon, Sony, Olympus, Panasonic, Fujifilm, Pentax, Leica, etc.

Q: How far is the transmission distance for wireless flash shooting?
A: The transmission distance is about 100 meters.

Q: Can I control the flash wirelessly?
A: Yes, you can control the flash wirelessly using compatible transmitter units like XPROII series, X3 series, X2T series, V1Pro series, V1 series, V860III series.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>