125 Bar Poly Pro Surface Cleaner User Manual
- August 19, 2024
- BAR
Table of Contents
WHIRL-A-WAY
125 BAR2000Y (OEM: 85.403.011)
WHIRL-A-WAY USER’S MANUAL
User Manual
V1.0 2024
INTRODUCTION
Attention: Read through the complete manual prior to the initial use of your
Whirl-A-Way
Using the Operator’s manual
The operating manual is an important part of your Whirl-A-Way. It should be
read thoroughly before initial use and referred to often to make sure adequate
safety and service concerns are being addressed.
Reading the owner’s manual thoroughly will help avoid personal injury or
damage to your pump. The information in this manual will offer you the most
effective tools for cleaning as well as the safest. By knowing how best to
operate this machine you will be better positioned to show others who may also
operate the unit.
This manual contains information for the complete range of BE Whirl-A- Ways,
and is placed in order starting from the safety requirements to the operating
functions of your pump. You can refer back to the manual at any time to help
troubleshoot any specific operating functions, so store it with the machine at
all times.
WARNING This product can expose you to chemicals including lead, which is
known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information, go to
www.P65Warnings.ca.gov.
PRODUCT IDENTIFICATION
Record Identification Numbers
Whirl-A-Way
If you need to contact an Authorized Dealer or Customer Service line
(61-2-4577-2144) for information on servicing, always provide the product
model and identification numbers. You will need to locate the model and serial
number for the pump and record the information in the places provided below.
Date of Purchase:
Dealer Name:
Dealer Phone:
Product Identification Numbers
Model Number:
Serial Number:
OPERATING INSTRUCTIONS
Set-Up
- Fit the lower portion of the handle into the mounting brackets on the cover and secure with the bolts or the pins & clips.
- Next, tighten the “fixed” hose end into the gun mounted onto the upper portion of the handle. Use Teflon tape on the hose ends.
- Once this is complete, join the two sections of the handle together and secure with the bolt or the pin & clip. Tighten the swivel end of the hose into the top of the rotary head.
- Turn the cover over and check to ensure that the nozzle tips are securely tightened and the spray pattern is in line with the rotary arm.
- It is important to adjust and tighten the rotary head so the rotary arm spray tips are a minimum of 1″ distance from the surface being cleaned.
Operation
The Surface Cleaning System you have purchased connects directly to your high
pressure hose and pressure washer by means of quick couplers, operating to a
maximum of 4000 PSI. This Whirl-a-Way is designed to operate with both hot &
cold water pressure washers. We do not recommend the use of hot water as the
nylon brush skirt will soften and wear prematurely, voiding any warranty. We
recommend that you supply grease to the rotary head every 30 40 hours of
use.
During operation, should you experience a buildup of small stones or other
foreign material within the cover, we recommend that you simply tip the
cleaner on its side at 45° which should expel any foreign materials. This will
give longer wear to your tips and swivel arm.
The tips that have been installed on your surface cleaning system permit the
use of your cleaner with a pressure washer producing up to 7 GPM at 4000 PSI.
Higher GPM tips should be installed if your pressure washer has a higher
GPM/PSI rating. Periodically check the tips to ensure they are not plugged by
dirt particles.
It is very important when operating your Whirl-a-Way, that you maintain a
continuous motion. Should you leave the cleaner in a stationary position, the
surface being cleaned can be seriously damaged by the high pressure. The
distance of the nozzle tips from the surface can be adjusted by loosening the
bolt on the rotary head mounting collar and adjusting the rotary head up or
down. Be certain the allen head bolt is tightened again to prevent the rotary
head from moving during operation.
Please ensure that your rotary head is adjusted to maintain a minimum of 1″
clearance between the spray tips and the surface being cleaned.
While operating your surface cleaning system, please ensure that the nylon
brush skirt remains in contact with the surface being cleaned. Do not operate
on vertical or overhead surfaces. We strongly recommend that safety eye
goggles, gloves and work boots be worn when operating this Whirl-a-Way. Keep
hands and feet away from the high pressure, high speed rotating arm that is
protected by the plastic cover.
Should your surface cleaner not be used for long periods of time, it is
recommended that you remove the hose from the top of the rotary head and a
vegetable oil be used to lubricate the swivel head’s internal parts.
Manually turn the rotary arm to allow lubrication of all internal parts before
storing.
You will quickly find your surface cleaning system a welcome addition to your
pressure washing applications. It is designed to give you a safe and rapid
method for cleaning hard surfaces, and will save you time in comparison to
using a conventional gun and wand. The durability of this surface cleaning
system is enhanced by the way it is handled by the operator. Please take care
to ensure that the Whirl-A-Way is not continuously being swung against
buildings, curbs, or other objects as this can damage the cover. Also, be
aware that the high speed rotating arm must not come in contact with rigid
protruding objects which can quickly damage or completely break off the steel
arm. Finally, do not apply excessive weight to the plastic cover.
PARTS DIAGRAM
125 BAR2000Y (OEM: 85.403.011)
PARTS LIST
125 BAR2000YN (OEM: 85.403.007)
| NO# | PART # | DESCRIPTION |
|---|---|---|
| 1 | 85.792.003 | Bracket, Mounting Head 20” |
| 2 | 85.790.004 | Rotary Head, 20” |
| 3 | 85.792.004 | Mounting Blocks |
| 4 | 85.238.059 | Hose, 62” x 3/8” |
| 5 | AC7501 | Easy Pull Gun |
| 6 | 85.300.105 | Plug, 3/8” MNPT |
| 7 | 85.792.002K | Handle |
| 8 | 85.602.005 | Hand Grip |
| 9 | 85.792.006 | Brush, 20” |
| 10 | 85.792.005 | Cover, Polypropylene 20” |
| 11 | 85.792.007 | Rotary Arm, 20” |
| 12 | 85.225.025 | Nozzle, 25 Deg. 025 |
| 13 | 85.791.020 | Sleeve For DC5090 WAW Gun |
125 BAR2000Y (OEM: 85.403.011)
See 125 BAR2000YN for parts 1-13.
| NO# | PART # | DESCRIPTION |
|---|---|---|
| 14 | 85.793.016 | Castor Kit |
NOZZLE REQUIREMENT
| PUMP OUTPUT | NOZZLE REQUIREMENT | QTY |
|---|---|---|
| 3 GPM | 85.225.020 (2 GPM/25°) | 2 |
| 4 GPM | 85.225.025 (2.5 GPM/25°) | 2 |
| 5 GPM | 85.225.030 (3 GPM/25°) | 2 |
| 6 GPM | 85.225.035 (3.5 GPM/25°) | 2 |
ROTARY HEAD REPAIR PARTS
A repair kit for this Whirl-a-Way’s rotary head, is available.
If you encounter problems with the rotary head after the 1 year warranty has
expired, this repair kit (part #85.790.010) allows you to replace the inner
components very quickly.
The rotary head has a snap ring on the bottom holding all the bearings inside.
By removing the snap ring and washer, you can tap off the outer shell with a
hammer while the output shaft is held in a vice. The rotary head repair kit
can then be used to replace the worn items inside the rotary head shell.
| NO# | PART # | DESCRIPTION |
|---|---|---|
| 1 | 85.790.010 | Rotary Head Rebuild Kit |
| 2 | 85.790.001 | Inlet Valve |
| 3 | 85.790.002 | Inlet Valve Viton O-Ring |
| 4 | 85.790.011 | Outlet Shaft |
WARRANTY
This surface cleaning unit has a 1-Year warranty on all components except for
the nylon brush ring. This includes the rotary head, spray gun, hose, the
nylon brush ring, and plastic cover.
This warranty covers manufacturer defects only and does not extend to any
damage caused by the user. It also does not extend to any wear and tear caused
by regular use of the product.
Distributed in Australia by
CONTACT DETAILS
B.A.R Group P/L
15 Hudson Place,
Mulgrave, NSW, Australia 2756
Phone: 02 4577 2144
www.bargroup.com.au
Distributed in New Zealand by
CONTACT DETAILS
BE Pressure Supply
541D Te Rapa Road, Te Rapa,
Hamilton 3200, New Zealand
Phone: 07 849 0000
www.bepressure.co.nz
Errors and omissions excepted.
Specifications and performance may change.
OPERATORS MANUAL
Version 5.1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>