Zildjian E-VAULT Electronic Drum Module User Guide

Zildjian E-VAULT Electronic Drum Module

Specifications

• Power: AC adapter
• Inputs: Trigger inputs, main output, aux input, multi outputs, MIDI in/out, USB-C, memory slot
• Controls: Power button, D-Pad, touchscreen, encoder, main volume buttons

Frequently Asked Questions

Q: How do I format the USB flash drive for system updates?

A: Follow these steps to format the flash drive:

1. Access the System Settings screen from the SYSTEM workspace menu.
2. Select the [Format] tab.
3. Insert the flash drive into the MEMORY slot.
4. Press the [Format USB Memory] button to format the drive.

Q: Can I use the included AC power adapter worldwide?

A: Yes, the AC power adapter is compatible worldwide. Use the appropriate plug for your country’s power outlet for safe operation.

SCAN THE QR CODE TO:

1. View videos for drum kit setup
2. Download firmware and sound updates
3. View videos for module navigation and setup
4. Access the full digital User Manual

E-VaulT Module

TOP PANEL

1. POWER
   Press the power button to turn the module on and off.

2. D-PAD
   Use the directional buttons to navigate the screen and select various controls and settings.

3. HEADPHONES
   Connect headphones to the ¼” (6.35mm) output jack and turn the knob to adjust the volume.

4. TOUCHSCREEN
   The touchscreen interface enables interactive control over system navigation and settings.

5. WORKSPACES
   Press a workspace shortcut button to access its screens and functions. To access the System Workspace, long press the [O] button.

6. ACTIONS
   When the corresponding icons are displayed, press the [X] button to cancel actions and exit screens, or the [O] button to execute actions.

7. ENCODER
   Turn the encoder knob to adjust the value of a control or setting.

8. MAIN VOLUME
   Press the [-] and [+] buttons to adjust the main output volume in steps.

REAR PANEL

1. TRIGGER INPUTS
   Connect the trigger outputs of the drums and cymbals to the corresponding trigger inputs on the module. Connect the drums using the included ¼” (6.35mm) TRS jack cables. Connect the cymbals using the included RJ45 cables.

2. MAIN OUTPUT
   Use ¼” TRS jack cables (not included) to connect the MAIN L–R balanced outputs to a mixer, drum amplifier, or audio interface. Unbalanced TS jack cables can also be used.

3. AUX INPUT
   Connect a stereo audio source using a ⅛” (3.5mm) TRS mini-jack cable (not included). The auxiliary input is designed for music players and audio devices that output a line level signal.

4. MULTI OUTPUTS
   The module’s multi-output matrix routes audio from instruments and groups to 8 balanced ¼” TRS outputs. Connect these outputs to a mixer or audio interface.

5. MIDI IN | OUT
   Connect an external MIDI device using 5-pin DIN cables (not included).

6. DC IN
   Connect the included AC adapter.

7. USB-C
   Use a USB-C cable (not included) to connect the module to a computer. Zildjian E-VAULT is a class-compliant audio device that supports multi-channel audio and MIDI data transmission.

8. MEMORY
   Connect the included USB flash drive to carry out system updates and backups. The flash drive must be formatted before it can be used.
   Format Flash Drive

9. From the SYSTEM workspace menu, access the System Settings screen.

10. Select the [Format] tab.

11. Insert the flash drive into the MEMORY slot.

12. Press the [Format USB Memory] button to format the drive.

About the Power Adapter
The included AC power adapter can be used worldwide.
Attach the included plug that is compatible with your country’s power outlet type.
For safe operation, use only the included AC power adapter and plug.

Setup

MOUNTING PLATE
Affix the plate to the bottom panel
The supplied mounting plate is used to mount the module onto a compatible drum stand or rack.

1. Align the mounting plate with the screw holes and guides located on the module’s bottom panel.
2. Attach the mounting plate using the included M5-10mm screws.

CONNECTING DRUMS

Connect the drums using the included ¼” (6.35mm) TRS jack cables as shown.

1. Connect the drum trigger outputs to their corresponding trigger inputs (KICK, SNARE, TOM 1-4) on the module’s rear panel.
2. Connect the right-angled end of the cable to the drum trigger output and the straight end to the jack input.
3. Secure the cables with the supplied cable ties.

CONNECTING CYMBALS

Connect the cymbals using the included RJ45 cables as shown.

1. Connect the cymbals to their corresponding trigger inputs (RIDE, CYM 1-4) on the module’s rear panel.
2. Connect the right-angled end of the cable to the cymbal and the straight end to the module input.
3. Secure the cables with the supplied cable ties.

CONNECTING THE HIHAT

1. To connect the hihat, run the straight-to-straight RJ45 cable up through the cable guide on the bottom cymbal and connect it to the terminal on the top cymbal. Connect the other end to the HI-HAT trigger input on the module’s rear panel as shown.
2. Secure the cable with a cable tie.

KIT MODEL CONNECTIONS

Use the reference tables as a guide to connecting your kit model’s drums and cymbals to the E-VAULT module’s trigger inputs.

ALCHEM-E Gold EX

Free inputs enable you to expand your kit with additional drums and cymbals from our ALCHEM-E lineup.

ALCHEM-E Gold

ALCHEM-E Bronze EX

Getting Started

E-VAULT WORKSPACES
The Zildjian E-VAULT System has five workspace areas that are instantly accessible via shortcut buttons. These shortcuts enable quick navigation to any system screen and function.

1. Kit Workspace
   Press the KIT button to open the Kit Play screen. The main function of this screen is to select kits to play or edit. Press the menu icon to open the Kit Workspace Menu screen and access functions for managing kits (Copy, Rename, Delete).

2. Instrument Workspace
   Press the INST button to open the Instrument Selection screen. The main function of this screen is to select instruments to play or edit. Press the menu icon to open the Instrument Workspace Menu screen and access functions for managing instruments (Copy, Rename, Delete).

3. Trigger Workspace
   Press the TRIG button to access trigger settings screens for drums, cymbals, and hihat control. Use the Drum-Cymbal selector to switch betwen the Drum Trigger and Cymbal Trigger screens.

4. Mix Workspace
   Press the MIX button to open the kit mixer screens. Use the Drum-Cymbal selector to switch between the MIXER Drums and MIXER Cymbals group views. Press the mixer icon to access the Mix Hub screen and set input-output volume levels and routing. Press the menu icon to open the Mix Workspace Menu and access screens for Multi-Out routing, and FX settings.

5. System Workspace
   Long press the [O] button to open the System Workspace Menu screen and access screen functions for system settings, MIDI setup, sound updates, backups, and system updates.

POWER ON | OFF

Turning the power on

1. Lower the volume of the connected amplifier and speakers.
2. Long press the power button to power on the module. Release the button when its LED is illuminated.
3. The Zildjian E-VAULT logo displays to confirm the system is starting up.
   A message displays if the drums or cymbals are played during the startup. The drums or cymbals should not be played as a series of calibrations and checks are performed by the system.

Turning the power off

1. Lower the volume of the connected amplifier and speakers.
2. Long press the power button and release it when a message displays prompting you to confirm E-VAULT Shutdown by pressing the power button a second time.
3. The Zildjian E-VAULT logo displays to confirm the system is shutting down.
   Do not disconnect the AC adapter to turn off the power.

FIRST TIME SETUP
Select Kit Model and Initialize Trigger Profile Settings
The E-VAULT Setup screen displays when the module starts for the first time. Follow the onscreen instructions to initialize the system with default trigger profile settings.

1. Select the option that matches your ALCHEM-E Kit Model:
   Gold EX, Gold, or Bronze EX. Press [Continue].

2. Select the option that is closest to your dynamic playing style: Light, Medium, or Heavy. Press [Finish].
   When the initialization is completed, the Kit Play screen displays.
   Press the TRIG button to access and adjust the trigger settings for different drums and cymbals.

Playing

PLAYING KITS
Press the KIT button to display the Kit Play screen. Select kits, play the metronome, and access other kit workspace screens.

• Menu
  Press the menu icon to open the Kit Workspace Menu screen.

• XSTICK Button
  Press the [XSTICK] button to switch the snare drum’s cross stick ON – OFF.

• Kit Selection Box
  Turn the encoder to select kits. Press the box to open the Select Kit screen.

• Metronome
  Press the metronome icon to play and stop the metronome.

• BPM | Settings Tabs
  The box displays the metronome BPM. Press to open the Settings Tabs.

• Kit View
  Kit View Modes visualize kit-instrument assignments and playing inputs.

• Kit Edit Button
  Press the [ Edit] button to open the Edit Kit screen.

METRONOME SETTINGS
Press the BPM box on the Kit Play screen to display the screen’s settings tabs. The metronome settings tab is selected by default. Press the icon to close the settings tabs.

• Metronome Sound
  Open the dropdown list to select between different metronome sounds.

• BPM
  Controls the metronome’s tempo. The setting range is 40 to 300 bpm.

• Beats
  Sets the number of beats in a measure. The setting range is 2 to 16 beats.

• Metronome Level
  Controls the metronome’s volume level (dB). This setting can also be adjusted on the Mix Hub screen.

• Metronome Pan
  Controls the stereo panning position of the metronome sound.

• Beat Accent
  When set to ON, a different sound will play on the first beat of the measure.

KIT MIXER
Press the MIX button to open the kit mixer. The 12 mixer channels are split into drum and cymbal groups. Use the Drum-Cymbal Selector to switch between the mixer group views.

• Mix Hub
  Press the mixer icon to open the Mix Hub screen.

• Mixer Lock
  Press the lock icon to disable direct touch control of volume and pan. When locked, the D-Pad and encoder can still be used to select and adjust volume and pan.

• Mixer Information
  Indicates the displayed mixer group and the selected Kit.

• Drum-Cymbal Selector
  Press to switch between the MIXER Drums and MIXER Cymbals group views.

• Pan Controls
  Select the rotary knob and adjust the stereo panning position of each drum and cymbal. The setting range is .

• Volume Controls
  Select the fader knob and adjust the volume level for each drum and cymbal. The setting range is -99.9 dB to +10.0 dB.

MIX HUB
The Mix Hub screen features mix fader and routing controls for E-VAULT’s input and output channels. Screens for FX settings and Multi-Out routing workspace are accessed from the mix hub.

• Menu
  Press the menu icon to open the Mix Workspace Menu screen.

• Save Kit Button
  Press the [ Save] button to save settings for the current kit.

• **FX***
  Press the icon to open the FX screen.

• MIX | KIT PLAY Volume Controls
  The faders control the Kit Volume Level and Metronome Volume Level.

• MIX| INPUT Volume Controls
  The faders control the input volume levels of stereo audio sources: AUX INPUT, Bluetooth® and USB-IN.

• MIX | OUTPUT Volume Controls
  The faders control the MAIN OUTPUT volume level and Headphones level.
  Tip: On the mixer screens, use the D-Pad to select a pan knob or volume fader, and turn the encoder to adjust the value.

Trigger Settings

DRUM & CYMBAL INPUTS
Press the TRIG button to open the Drum Trigger and Cymbal Trigger screens. Use the Drum-Cymbal Selector to switch screens and display corresponding buttons for selecting inputs.

• Save Trigger Profile Button
  Press the [ Save] button to save the trigger settings (Trigger Profile).

• Trigger Information
  Displays the active trigger settings screen and the trigger profile name.

• Drum-Cymbal Selector
  Press to switch between the Drum Trigger and Cymbal Trigger screens.

• Trigger Input Indicators
  Graphic indicators visualize the zone triggering for the selected input.

• Trigger Settings Tabs
  The tabs contain the trigger settings for the selected input. The organization of trigger settings in tabs is generally consistent across inputs:
  [Basic] Preset, Threshold, Zone Mode
  [Zone Tabs] Gain, Curve, Detection Sensitivity

HIHAT CONTROL SETUP
To set up the E-FAMILY hihat, access the Cymbal Trigger screen and press the [HH CTRL] button. The [Set] tab displays the three step buttons used in setting up hihat control.

The scale-bar graphic and Range value indicate the current position of the hihat top cymbal relative to the bottom cymbal. To set up the open-close control function of hihat, follow the instructions for each step:

• Step 1: Calibrate
  Unlock the hihat clutch and allow the top cymbal to rest on the bottom cymbal. Press the [1. Calibrate] button to set the calibration point.

• Step 2: Set Open Point
  Lift the top cymbal to the required height and lock the hihat clutch. You should see the indicator bar and range value change. Press the
  [2. Set Open] button. The open point value is set and shown on the scale.

• Step 3: Set Close Point
  Close the hihat with natural foot pressure. Press the [3. Set Close] button when the range value is lower than the calibrate and set open point values. The close point value is set and shown on the scale.

On completing the three steps, Press the [ Save] button to save the settings.
Note: Each step can be peformed independently when required. The message ‘COMPLETE’ displays when a step is completed correctly. The instruction message ‘RETRY’ displays when an invalid value (INV) is set.

Important Notices

SPECIFICATIONS
The specifications and appearance of this product are subject to change without notice for improvement.

TRIGGER INPUTS terminal x 6: RJ45 type (exclusive use with cymbals)

AUDIO OUTPUTS (MAIN) jacks (L, R): 1/4-inch (6.35mm) TRS phone type, balanced AUDIO OUTPUTS (MULTI OUTPUTS) jack x 8: 1/4-inch (6.35mm) TRS phone type, balanced

HEADPHONES jack: Stereo 1/4-inch (6.35mm) phone type (32 ohms recommended) AUX INPUT jack, Stereo 1/8-inch (3.5mm) miniature phone type

MIDI (IN, OUT) 5-PIN DIN Connectors

USB-C port: USB-C type, supports high-speed MIDI and multi-channel audio MEMORY: USB Flash Drive (FAT32, 32GB maximum)

DC IN jack

USB Audio| Zildjian E-VAULT is a USB Class Compliant audio device 48 kHz, 16-bit audio

Output: 10 channels

Input: 2 channels

Bluetooth®| Input: 2 Channel, Stereo (A2DP)
Power Source| AC Adapter (DC 12V)
Current **Consumption*| 2A
Dimensions**| 300 (W) x 166 (D) x 78.9 (H) mm

13 (W) x 6-9/16 (D) x 3-1/8 (H) inches

Weight| 2.19 kg/4 lbs 13.1 oz
Accessories| Quick Start Guide

12V DC 2.0A 24W Power Adapter 32GB USB Flash Drive Microfiber Cleaning Cloth

Mounting Plate (Black, with four M5 x 10mm screws)

*Average current consumption is around 1.6A
About E-VAULT System Updates: Scan the QR code at the front of this guide and navigate to the website area where you can download the latest E-VAULT updates. Follow the provided instructions to install firmware updates and sound updates.

SAFETY INFORMATION

Important Safety Instructions and Warnings.
Please read carefully before using the device. Make sure to follow all instructions and warnings as failure to do so may result in injury and/or property damage. Keep these instructions for future reference.

About Warnings and Cautions

WARNING
Indicates a hazard that could result in death or serious injury

CAUTION
Indicates a hazard that could result in injury or property damage

About the Symbols

• “Caution”: Calls your attention to a point of caution
• “Do not …”: Indicates a prohibited action
• “You must …”: Indicates a required action

WARNING

• Use only the included or designated power supply
  Ensure that power cord is grounded and plugged into an outlet with a protective earthing connection
  Use only the correct voltage connection for your area
  When plugging in or unplugging the instrument, grip and pull from the plug, not the cord. Pulling on the cord may damage it and lead to an electric shock which could cause injury or death.

• Do not handle the power supply with wet or damp hands to prevent the risk of electric shock which may cause injury or death.

• If the AC adapter cord or plug becomes frayed or damaged, or if there is a sudden loss of sound during use of the instrument, or if any unusual smells should appear to be caused by it, immediately turn off the power switch, disconnect the adapter plug from the outlet, and have the instrument inspected by qualified service personnel. Using a damaged power supply can lead to fire or electric shock.

• Do not excessively bend, place heavy items on, or otherwise damage the power supply cord. A damaged power supply can lead to fire or electric shock.

• Always keep small parts away from children and pets as they could be ingested leading to injury or death. To prevent injury, do not let children use the instrument without adult supervision.

WARNING

• Do not expose to direct sunlight, extreme temperatures (hot or cold), humidity, excessive dust or direct strong virbrations or shocks or close to magnetic fields.
• Do not expose to rain, use it near water or in damp conditions. Do not place any containers containing liquids onto the module.
• Do not place in a position where anyone could walk on, trip over or roll anything over the power or connecting cords. This could lead to injury or damage to the instrument.
• Do not place the instrument in an unstable position where it may fall over as this could lead to injury or damage to the instrument.

CAUTION

• Unplug the power supply when not in use or in the event of electrical storms.
• Periodically clean the plug and remove any dust which may have accumulated. Do not use the power supply if the plug is dusty as this can cause fire or electric shock.
• Do not use the power supply near heat sources such as heaters or radiators as this could cause the power supply to overheat, risking burns or fire.
• Before connecting to other devices, turn off the power to all instruments. This will help prevent malfunction and/or damage.
• Do not connect the power supply to an electrical outlet using a power strip. This can result in reduced sound quality or possibly cause overheating in the outlet, leading to risk of fire.
• This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing sound levels that could cause permanent hearing loss. DO NOT operate for long periods of time at a high-volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist.

CAUTION

• Do not use the supplied power adapter or cord with other electronic devices.
• Avoid plugging the power supply into outlets with other high power consumption appliances such as electric heaters or ovens.
• Turning off the instrument does not disconnect it from the power supply. To ensure the instrument is completely powered down, the power cord must be removed from the outlet.
• Do not rest your weight on, or place heavy objects on the instrument or use excessive force on the buttons, knobs or connectors.
• Allow for adequate air circulation and avoid obstructing vents on the module to avoid internal heat buildup. An over heated module could lead to burns and damage to the instrument.
• Disconnect all cables before moving.
• Do not allow any paper, metallic or other objects into the instruments. If this occurs, unplug the instrument and have it inspected by a qualified service personnel.
• Do not drop the product or subject it to high impact as this could damage the instrument.
• The instrument should only be used with supplied or manufactured recommended components. If a third-party component is used, please observe all safety marking accompanying that product.
• Do not open the module, there are no user-serviceable parts inside.

IMPORTANT INFORMATION

• Preventing Data Loss

  • Data stored in the module can be lost due to equipment failure, incorrect operation, or other causes. Creating regular back ups can protect you from any data loss.
  • Zildjian assumes no liability regarding any data loss.

• Packaging Disposal
  You must comply with the waste disposal regulations in your locality when disposing of the packaging the instrument was shipped in.

• Connecting and using a USB Flash Drive

  • Prior to inserting the USB drive into the module, discharge all static electricity from your person to prevent damage
  • Do not remove the USB drive while reading or writing is in progress.

• Intellectual Property Rights

  • The copyright of content in this product (the sound waveform data, style data, accompaniment patterns, phrase data, audio loops and image data) is reserved by Zildjian.
  • The original content and any subsequent sounds provided by Zildjian are for personal use by the purchaser and for use in the production and distribution of original compositions. Do not use the instrument in any way that could infringe on another’s copyright. Zildjian assumes no liability regarding any infringements of a third-party’s copyright arising through your use of the instrument.
  • The included content and any subsequent sounds provided by Zildjian cannot be extracted and distributed in original or modified form.

• About this Document
  Zildjian E-VAULT Electronic Drum Module Quick Start Guide (ZAQSG): Version 1.1 (D)

For EU countries, and UK

Avedis Zildjian Co. hereby declares that the type of radio equipment Zildjian ALCHEM-E (ZEV1, ZABEX, ZAG, ZAGEX) complies with Directive 2014/53/EU (CE), and 2017 No.1206 (UKCA). The full text of the EU Declaration of Conformity is available at: https://zildjian.com/pages/alchem-e-support

This symbol on the product means that used electrical and electronic equipment should not be mixed with general household waste. The correct disposal will help prevent potential negative effects on human health and the environment. For proper treatment, recovery and recycling, please contact your city office, waste disposal servicer or the shop which you purchased the product.

How to Display Certification IDs

How to display this product’s Certification IDs (FCC, IC ID, JP)
With the device powered on, follow the steps:

• Step 1 – Press the [O] button for two seconds.
• Step 2 – Press the [ Settings] button.
• Step 3 – On the System Settings screen, select the [Info] tab to display the Certifcation IDs .

Bluetooth®

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by the Avedis Zildjian Co. is under license. Other trademarks and trade names are those of their respective owners.

For the USA

WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes of modifications not expressly approved by the party responsibile for compliance could void your authority to operate the equipment.

RF Exposure Statements:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equiment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
   This equiment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons.

Avedis Zildjian Company
22 Longwater Drive, Norwell,
Massachusetts 02061, USA
Tel: 1-781-607-2424

For Canada

IC INFORMATION

Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Avedis Zildjian Company
22 Longwater Drive, Norwell, Massachusetts 02061, USA
Tel: 1-781-607-2424

an immersive elevated electronic experience

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>