SEALEY LED1801, LED1801K SMD LED Rechargeable SLIM Folding Inspection Light User Manual

: August 15, 2024
: SEALEY

Table of Contents

SEALEY LED1801, LED1801K SMD LED Rechargeable SLIM Folding Inspection
SAFETY
INTRODUCTION
SPECIFICATION
OPERATION
MAINTENANCE
Warranty
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SEALEY LED1801, LED1801K SMD LED Rechargeable SLIM Folding Inspection

Light

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

GENERAL

It is important to ensure that the lamp is fully charged before initial use.
DO NOT turn the lamp on when it is being charged.
DO NOT shine directly into your, another person’s, or an animal’s eyes.
DO NOT allow children to use the lamp.
DO NOT leave the battery in a discharged state. Recharge the battery immediately.
Recharge the battery at least once every six months of non-use.
There are no user-serviceable components. DO NOT dismantle.
DO NOT pull the charger plug from the main socket by the lead.

BATTERY SAFETY

WARNING! To reduce the risk of burns or fire:
DO NOT Attempt to open, disassemble, modify, or service the battery pack.
DO NOT Crush, puncture, short external contacts or dispose of in fire or water.
DO NOT Expose to temperatures above 60° C (140° F).
Recycle or dispose of used batteries as stipulated by local regulations.
If the electrolyte in the cells gets on your skin, thoroughly wash it with water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention.

INTRODUCTION

LED1801:

Slimline foldout inspection light for use in confined spaces, with a 6mm minimum thickness. The inspection arm can be rotated 180° and folded back for use as a hands-free inspection light. Features 5W SMD LED which produces up to 500 lumens, operated by a rolling dimmer switch, and a 1W SMD LED in the end for use as a directional torch. Suitable for hands-free operation with three magnets and a hanging hook.
Folds away, is small and compact, suitable for keeping in your pocket. Can be charged in a Sealey docking station – LED1801 K (not included).
Powered by a 3.7V 2.6Ah rechargeable lithium-ion battery which lasts up to 8hr. Supplied with USB charging lead.

LED1801K:
The docking station kit includes 2 x LED1801 and a charging station. Each inspection light has 5W SMD LED (side)+ 1W SMD LED (top) producing up to 500 lumens. When both inspection lights are docked it can be used as a floodlight with two light options 50% and 100% producing 500 or 1000 lumens. Each inspection light can extend and rotate 180° making it easy to direct the light. Two charging points with individual LED charging level indicators. Includes 5V-2A mains adaptor and 1 m Micro USB charging cable.

SPECIFICATION

OPERATION

CHARGING
The battery fitted to this lamp is considered to be a consumable item and its ability to accept charge will reduce over time. We will warranty it against mechanical and electrical defects for one year, this does not cover fair wear and tear. If the battery is not properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances, we will not replace the battery even if it is less than one year old.

Note:
The torches will flash when the battery gets low.

Connect the charger to the charge socket on the lamp, see fig.1.
Plug into the power supply and turn it on, the red charge LED on the lamp will light as the battery charges. When fully charged the LED turns green.
When the battery has fully charged (approx 3hrs) Disconnect from the mains supply.

Note:

The Lithium battery does not suffer from the memory effect and once fully charged may be stored for up to six months without another charge.
Unfold lamp. Select either a directional torch or an inspection lamp.
Brightness is controlled by a dimmer switch.
The lamp can be hung from the hook or attached using magnets.
When the lamps are docked in the station (LED1801 K) you can turn both of the docked torches on by using the On/Off button on top of the unit.

MAINTENANCE

Keep the lamp clean and check for damage before every use. If damage is observed, remove it from use until the unit is repaired.
The battery is not designed to be removed.

Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk, or telephone 01284 757500

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

REGISTER YOUR PURCHASE HERE

WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd is required to inform potential purchasers of products containing batteries (as defined within these regulations).

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.