Hummingbird Mobile Computer Workstations
SmartDrawers User Manual

Preface

Important, Please Read Carefully
Thank you for your purchase with Amico.
This unit is designed for long-lasting performance, providing the end-user complies with assembly and maintenance procedures. This User Manual is your guide to ensure that you get the best performance out of the equipment. Amico Accessories Inc. is not responsible for any damage as a result of, but not limited to, abuse and other problems that may be a direct or indirect result of failure to comply with the instructions provided in this manual.
Glossary of Warning Symbols
The meaning of symbols appearing in this User Manual, on the workstation, or on the battery system are shown on the chart below. These symbols alert you to safety conditions that demands your attention. You should take proper precaution and follow the instruction on the label and/or this User Manual to minimize the risk of injury or damaging the equipment.

avoided, could result in death or serious injury.
| NOTE| Follow operating instructions.

Medical Facility Responsibilities
Preventive maintenance checks must be performed regularly to maintain the quality and performance of this product.
Any parts that may be broken, missing, worn, distorted, or contaminated in any way should not be used and all affected parts should be replaced immediately. Should the necessity of any repair be suspected; please contact your local distributor or call 877-264-2697.
Precautions
WARNING: IT IS THE INSTALLER’S RESPONSIBILITY TO ENSURE ALL COMPONENTS ARE PROPERLY ASSEMBLED AND INSTALLED USING THE PROVIDED INSTRUCTION MANUAL.
WARNING: EXCEEDING WEIGHT CAPACITIES CAN RESULT IN SEVERE PERSONAL INJURY OR DAMAGE TO YOUR EQUIPMENT. IT IS THE INSTALLER’S RESPONSIBILITY TO ENSURE THE COMBINED WEIGHT OF ALL COMPONENTS DOES NOT EXCEED THE WEIGHT CAPACITY LISTED IN PRODUCT SPECIFICATIONS ON PAGES 1 & 2 OF THIS USER MANUAL.

Section 1: Product Specifications

Features

| Individual-unlocking Cabinet| All-unlocking Cabinet
---|---|---
Slam Lock| Yes| Yes
Auto Re-lock| Yes| Yes
Timed User Log Out| Yes| Yes
Individual LED Illumination for Opened SmartDrawers| Yes| No
LED Indicator for SmartDrawers Unlock| Yes| Yes
Emergency Manual Lock Override| Yes| Yes
Unlock SmartDrawers Through Interface| Yes| Yes
SmartDrawers Kick-out| Yes| No
Guest User Access| Yes| Yes
2-factor Authentication for Unlocking SmartDrawers| Yes| Yes
Editable SmartDrawers Label| Yes| Yes
Configurable SmartDrawers Layout| Yes| Yes

SmartDrawers Specifications

| Slim| Wide
---|---|---

|

Part Number| X-HMA-DRWASM-HG-SM| X-HMA-DRWASM-HG-LG
Inside Dimension| 3.23″ x 11.69″ x 2.95″

(8.2 cm x 29.7 cm x 7.5 cm)

| 13.58″ x 11.42″ x 2.95″

(34.5 cm x 29.0 cm x 7.5 cm)

Net Weight| 0.8 lbs (0.4 kg)| 2.38 lbs (1.1 kg)
Max Load| 1.1 lbs (0.5 kg)| 4.41 lbs (2 kg)
Max Capacity| 0.41 gal (1.88 L)| 1.83 gal (8.3 L)
| Removable Dividers (optional)| Removable Dividers (optional)

Cabinet Specifications: Individually-unlocking Cabinet

| 1-row Slim SmartDrawers| 2-row Slim SmartDrawers| 3-row Slim SmartDrawers
---|---|---|---

|

|

Part Number| HMA-SDRW-A-400| HMA-SDRW-B-440| HMA-SDRW-C-444
Exterior Dimension| 17.83″ x 4.8″ x 16.18″

(45.3 cm x 12.2 cm x 41.1 cm)

| 17.83″ x 8.54″ x 16.18″

(45.3 cm x 21.7 cm x 41.1 cm)

| 17.83″ x 12.28″ x 16.18″

(45.3 cm x 31.2 cm x 41.1 cm)

Net Weight| 21.81 lbs (9.89 kg)| 33.38 lbs (15.14 kg)| 44.3 lbs (20.09 kg)
Storage Volume| 1.65 gal (7.5 L)| 3.3 gal (15 L)| 4.95 gal (22.50 L)

Cabinet Specifications: All-unlocking Cabinet

| 1-row Slim SmartDrawers| 2-row Slim SmartDrawers| 3-row Slim SmartDrawers
---|---|---|---

|

|

Part Number| HMA-SDRW-1-100| HMA-SDRW-2-110| HMA-SDRW-3-111
Exterior Dimension| 17.83″ x 4.8″ x 16.18″
(45.3 cm x 12.2 cm x 41.1 cm)| 17.83″ x 8.54″ x 16.18″
(45.3 cm x 21.7 cm x 41.1 cm)| 17.83″ x 12.28″ x 16.18″
(45.3 cm x 31.2 cm x 41.1 cm)
Net Weight| 20.41 lbs (9.25 kg)| 30.58 lbs (13.87 kg)| 39.53 lbs (17.93 kg)
Storage Volume| 1.83 gal (8.3 L)| 3.66 gal (16.6 L)| 5.49 gal (24.9 L)

Options Matrix

Section 2: Installation Preparation

What’s in the Box?
NOTE: Please ensure that your contents match the list as outlined below. If not, please contact Amico Accessories at 1-877-264-2697. For customers who purchase the SmartDrawers with a new Hummingbird cart, the cabinet would be delivered fully assembled with everything in one.
SPECIFIC CONFIGURATION HERE Project #: 0000
SPECIFIC CONFIGURATION HERE Project #: 0000
SPECIFIC CONFIGURATION HERE Project #: 0000
For 1-row Cabinet For 2-row or 3-row Cabinet Installation Tools NOTE: FOR CUSTOMERS WHO PURCHASE THE SMARTDRAWERS WITH A NEW HUMMINGBIRD CART, THE CABINET WILL BE DELIVERED FULLY ASSEMBLED AND NOT REQUIRING ANY TOOLS TO COMPLETE THE INSTALLATION.

Section 3: Installation

Cabinet Installation
NOTE: FOR CUSTOMERS WHO PURCHASE THE SMARTDRAWERS WITH A NEW HUMMINGBIRD CART, THE CABINET WILL BE DELIVERED FULLY ASSEMBLED WITH THE CABLE CONNECTED. PLEASE SKIP THE CABINET INSTALLATION AND PROCEED TO PAGE 13 FOR SMARTDRAWERS INITIAL SET UP.

1. Unplug the cart from power outlet and adjust the height to the maximum position. (See section 6 of the Hummingbird User Manual for details).

2. Follow page 32 of the Hummingbird User Manual to open the battery compartment, then disconnect the yellow Anderson 6331G8 Connector (Figure 1).

3. Slide 2x DOVETAIL SLIDES into the COLUMN’S side channels, use 2x #8 SET SCREWS to secure them at the position where the top of the DOVETAIL SLIDE is 9″ away from the bottom of the WORKTOP (Figure 2).

4. 4a. 1-row Cabinet(For 2-row or 3-row cabinets, please skip step 4a and proceed to step 4b on page 8).
   4a-Ι. Mount BACK MOUNTING PLATE onto 1-ROW CABINET with 8x #8 FLANGED SCREWS (Figure 3). 4a-ΙΙ.Mount BACK MOUNTING PLATE onto BACK MOUNTING BRACKET with 4x

   10 FLATHEAD SCREWS. Install CABLE into CONNECTOR, firmly press CONNECTOR

   until the lock tab is fully engage (click sound) (Figure 4). 4a-ΙΙΙ.Mount BACK MOUNTING BRACKET onto the DOVETAIL SLIDE with 4x #8 FLATHEAD SCREWS. Install RIGHT REAR COVER and LEFT REAR COVER (Figure 5). (Continue to step 5 on page 12, skip steps 4b-Ι to 4b-V ). 4b. 2-row or 3-row Cabinet
   (For 1-row cabinet, please complete 4a-Ι to 4a-ΙΙΙ on page 6 instead).
   4b-Ι. Mount BACK MOUNTING PLATE onto the BACK MOUNTING BRACKET with 4x #10 FLATHEAD SCREWS (Figure 6). 4b-ΙΙ. Install CABLE into CONNECTOR, firmly press CONNECTOR until lock tab is fully engage (click sound) (Figure 7). 4b-ΙΙΙ.Tilt the CABINET and insert the TOP FLANGE onto the BACK MOUNTING BRACKET. Slide the CABINET down slowly until the CABINET is fully seated on the BACK MOUNTING BRACKET (Figure 8). 4b-ΙV.Install 2x CABINET SECUREMENT SCREWS (Figure 9). 4b-V. Install RIGHT REAR COVER and LEFT REAR COVER (Figure 10). The rest of the CABINET installation (steps 5 – 9) are the same for all CABINETS.

5. Insert the CABLE into WORKTOP through the hole located on the back of the KEYBOARD TRAY (Figure 11).

6. Plug CABLE into the Hummingbird CONTROL INTERFACE (Figure 12).

7. Load the DRAWERS to the CABINET according to the selected layout (Figure 13).

8. Connect the yellow Anderson 6331G8 Connector in the battery compartment (Figure 14). Follow page 32 of the Hummingbird User Manual to restore and lock the battery compartment cover.

9. Plug in the cart’s power cord to a wall outlet. Wait for the startup of the cart which may take up to 20 seconds to complete.

SmartDrawers Initial Set Up
A. Locate Home Screen
Home Screen of the Hummingbird cart Control Interface (Figure 15). A SmartDrawers icon will appear when the cabinet installation and cart startup is complete.
SmartDrawers administrator control access and restrictions in operating the cart and SmartDrawers for registered Users or guests to adhere to system and facility policies. Please follow the instructions below on operation of the SmartDrawers and creating a new User profile.
B. Log In as Admin User
a. Log in as an “ADMIN” User with designated credentials and tap on “SETTINGS” (Figure 16).
WARNING: TO ENSURE THE SECURITY OF THE SYSTEM AND USERS, SET YOUR OWN DEFAULT PASSWORD. b. Tap on “SmartDr awe r ” (Figure 17) to access the configuration options for SmartDrawers setup (Figure 18). NOTE: TAKE NOTE OF THE FOLLOWING SECTION IF YOU ARE USING BIRDSEYE FLEET MANAGEMENT SOFTWARE IN YOUR HOSPITAL.
The following settings are controlled via the BirdsEye dashboard:

• Allow guest user access
• User can edit labels

Any changes made on the interface will be overridden by settings configured on the fleet management dashboard.
Refer to BirdsEye Window Client User Manual for further details.
The following settings can be modified or reset remotely by IT administrators using the dashboard:

• Prompt for Pin
• SmartDrawer Pin
• 2FA Pin
• Logout when inactive for (x-time)
• Lock drawer after (x-time)

NOTE: IF YOU ARE USING BIRDSEYE FLEET MANAGEMENT IN YOUR HOSPITAL, ENABLE 2FA (PROMPT FOR PASSWORD/PIN) WILL BE OVERRIDE BY THE DASHBOARD SETTINGS.

C. Configure Prompt for PIN
If enabled, access to the SmartDrawers is protected by a PIN, which can be configured by:

• Setting the PIN same as the User Login  credentials for accessing SmartDrawers, or
• Assigning a specific PIN for accessing the SmartDrawers. When this option is enabled, the default PIN is 5555 (Figure 19).

D. Cabinet Setup
Setup SmartDrawers layout on the control interface to mimic the physical SmartDrawers layout for easy identification of the Drawers (Figure 20). You may add up to 3 rows of SmartDrawers (Figure 21). E. SmartDrawers 2-factor Authentication (Bin 2FA) Setup
Admin Users can also enable and configure a 2-factor authentication for increased security in accessing the individual drawers in the SmartDrawers (Figure 22). Bin 2FA is not available for all-unlocking SmartDrawers cabinets. F. Other Admin Setup
A selection of admin setup is available (Figure 23). G. Add a New User
Follow the steps described below to add a new User (Figure 24). H. User Log In
Follow the steps described below to log in as a User (Figure 25).

Section 4: Operation Instructions

WARNING: PLEASE NOTE THAT THE OPERATOR NEEDS TO PHYSICALLY PUSH BACK ALL THE OPENED SMARTDRAWERS IN ORDER TO FULLY LOCK THEM.
PLEASE READ CAREFULLY
WARNING: PLEASE ENSURE TO LEARN ABOUT THE LOCK-UNLOCK TIMINGS OF THE SMARTDRAWERS PRIOR TO ACTUAL USAGE.
WARNING: DO NOT LEAN OR REST ANY OBJECTS ON OR SIDE OF THE SMARTDRAWERS CABINET.
WARNING: PLEASE ENSURE THE CABINET HAS ENOUGH CLEARANCE FOR DRAWERS TO OPEN WITHOUT ANY INTERFERENCE.
WARNING: DO NOT ATTEMPT TO INCLINE OR DECLINE THE CART FOR ANY SORT OF CLIMBING UP OR DOWN, THIS MAY DAMAGE THE ITEMS WITHIN THE SMARTDRAWERS.
WARNING: PLEASE NOTE THAT EACH SMARTDRAWER HAS A LOAD LIMIT OF 1.1 LB (0.5 KG) TO FUNCTION PROPERLY, EXCEEDING THIS MAY STRESS ON THE INTERNAL ELECTROMECHANICAL COMPONENTS AND RESULT INTO MALFUNCTIONING.
WARNING: USER HAS TO MAKE SURE THAT ITEMS SHOULDN’T BE FORCEFULLY SHOVED OR PUSHED INTO THE SMARTDRAWERS, AND MUST BE ABLE TO FIT SUBTLETY.
WARNING: PLEASE NOTE THAT FACILITY PERSONNEL ARE RESPONSIBLE FOR MANAGING THE ACCESS OF THE CONFIDENTIAL PHI (IF STORED IN ANY FORM) ON THE CART USER INTERFACE.
Access SmartDrawers

Tap on the “SmartDrawers” button on the home screen to get to the SmartDrawers control center (Figure 26).
Enter PIN (If prompted)
WARNING: TO ENSURE THE SECURITY OF THE SYSTEM AND USERS, SET YOUR OWN DEFAULT PASSWORD.
When prompted for PIN, enter the SmartDrawers Password and tap “OK” (Figure 27). NOTE: GUEST (NON-REGISTERED USER ON CART) CAN ACCESS SMARTDRAWERS BY ENTERING DEFAULT PIN 5555* (configuration set by facility).
Unlocking SmartDrawers
The SmartDrawers Control Center screen is a graphic layout of the actual SmartDrawers cabinet and will show the graphic version of the SmartDrawers installed on the cart.
To unlock, tap on the desired SmartDrawers icon. On an individually-unlocking cabinet, the selected SmartDrawers kicks open (Figure 28a).
On an all-unlocking cabinet, SmartDrawers are unlocked and ready to be open until the unlock status times out (Figure 28b). If 2FA enabled on an individually-unlocking cabinet, system will prompt for the drawer specific PIN. Enter PIN and tap “OK” to unlock the drawer (Figure 29). Locking SmartDrawers
When an open SmartDrawer is pushed all the way in, the SmartDrawer will lock.
For individual-unlocking cabinet, slam lock anytime. For all-unlocking cabinets, when the drawer icon returns from grey to white and the drawer’s light turns off, SmartDrawers will be locked (Figure 30). Editing SmartDrawers Labels
If enabled and allowed by Admin, to edit SmartDrawers label on screen,
I. Access SmartDrawers (see page 18).
II. Enter PIN if prompted (see page 18).
III. On the SmartDrawers Control Center screen, follow the steps described below to log in as a user (Figure 31).
The maximum string length is 10-15 characters for each slim SmartDrawer, and 25-32 characters for each wide SmartDrawer. Each drawer is also available with a printed label slot at the front. SmartDrawers 2-factor Authentication (2FA)
If enabled and allowed by the Admin, the User can protect individual drawers with a second level of security by setting individual passwords to each drawer. Password-protected drawers will have a shield on their respective icons (Figure 32). On the SmartDrawer Control Center screen, follow the steps described below to set the PIN.

Section 5: Troubleshooting

Please refer to Hummingbird cart User Manual
Error message “No Response from Cabinet”| • Miscommunication/disconnection| • Wait for 10 seconds and retry
• Reset SmartDrawers (Page 16)
• Verify cable connection
Error message “SmartDrawers Configuration Error”| • Miscommunication/disconnection| • Reset SmartDrawers (Page 16)
• Set up the SmartDrawers
• If still not working, contact Amico
Interface restart| •  Please refer to Hummingbird cart User Manual| •  Please refer to Hummingbird cart User Manual
SmartDrawers icon disappears| • Miscommunication/disconnection| • Reset SmartDrawers (Page 16)
• Unplug and re-plug the SmartDrawers unit
• Factory reset through Hummingbird ADMIN SETUP
• If still not working, contact Amico
Incorrect cabinet layout| • Miscommunication/disconnection| • Reset SmartDrawers through ADMIN SETUP
• Setup cabinet layout through CABINET SETUP
SmartDrawer not sliding properly| • Obstacle inside track
•  Incorrect installation
• Damaged components| • Remove the SmartDrawer from cabinet
• Inspect component for integrity
•  Make sure the track is free of obstacles
• Follow the instructions to install the SmartDrawer back into the cabinet
All-locking cabinet not locking|

•Obstructed lock plate
• Damaged components

| • Unlock and re-lock the manual key lock override
• Remove the SmartDrawers from the cabinet
• Ensure lock plate is moving up/down
• Check that individual lock latches are moving up/down properly
• If the symptom still exists, contact Amico
Individual-locking cabinet not locking| • Obstructed lock latches
• Damaged components| • Remove the SmartDrawers from cabinet
• Check individual lock latches moving up/down properly
• If the symptom still exists, contact Amico
Individual-locking cabinet does not unlock| • Obstructed lock latches
• Damaged components| • Use the override lock to unlock the SmartDrawers
• Remove the SmartDrawers from cabinet
• Check individual lock latches moving up/down properly
• If the symptom still exists, contact Amico

Section 6: Preventive Maintenance & Cleaning

Preventive Maintenance
WARNING: THE INTERVALS SHOWN ARE RECOMMENDED. MAINTENANCE SCHEDULES SHOULD BE MORE FREQUENT FOR HIGHER-USE AREAS.
WARNING: TO AVOID RISK OF ELECTRIC SHOCK, DO NOT EXPOSE ELECTRICAL COMPONENTS TO WATER, CLEANING SOLUTIONS, OR OTHER POTENTIALLY CORROSIVE LIQUIDS OR SUBSTANCES.
WARNING: DO NOT IMMERSE WORKSTATION OR COMPONENTS IN LIQUID OR ALLOW LIQUIDS TO FLOW INTO THE WORKSTATION.
WARNING: ADJUSTMENT, SERVICE, REPLACEMENT – DO NOT ATTEMPT TO ADJUST, SERVICE, OR REPLACE ANY PART OF THE HUMMINGBIRD MOBILE WORKSTATION UNLESS DIRECTED TO DO SO THROUGH AMICO APPROVED DOCUMENTATION (I.E. INSTALLATION INSTRUCTIONS). ONLY AMICO ACCESSORIES INC., OR AN AMICO-CERTIFIED ENTITY MAY ADJUST, SERVICE, OR REPLACE HUMMINGBIRD MOBILE WORKSTATION COMPONENTS. IF ANY COMPONENTS ON THE WORKSTATION ARE MISSING OR DAMAGED, THE WORKSTATION MUST NOT BE USED. CONTACT AMICO CUSTOMER CARE IMMEDIATELY TO REQUEST A REPLACEMENT PART.
WARNING: THIS WORKSTATION IS NOT INTENDED FOR USE IN A FLAMMABLE, ANESTHETIC MIXTURE, OR OXYGEN-RICH ENVIRONMENT.
WARNING: USE OF ACCESSORIES, TRANSDUCER, AND CABLES, OTHER THAN THOSE SPECIFIED OR PROVIDED BY AMICO COULD RESULT IN INCREASED ELECTROMAGNETIC EMISSIONS OR DECREASED ELECTROMAGNETIC IMMUNITY OF THE EQUIPMENT AND RESULT IN IMPROPER OPERATION.
It is recommended that once every three (3) months, all locks, bolts and, screws are visually inspected for signs of product wear and tear or damage. Check the product for looseness in the mount and ensure the adapter is secured to the rail.
Ensure the 2x SET SCREWS on the CHANNEL are fastened to the tightest possible position and ensure the cabinet is secure.

Cleaning
WARNING: THE CLEANING CHEMICALS AND METHODS BELOW ARE NOT MEANT FOR CONTROLLING ANY INFECTIONS. IT SHALL BE THE RESPONSIBILITY OF THE HOSPITAL OR THE HOSPITAL’S INFECTION CONTROL OFFICER TO SANITIZE THE EQUIPMENT.
WARNING: PLEASE DO NOT SPRAY ANY CHEMICALS DIRECTLY ONTO THE SMARTDRAWERS. APPLY ONTO A SOFT CLOTH AND WIPE CLEAN TO PREVENT CHEMICALS GETTING INTO THE INTERNAL COMPONENTS OF THE SMARTDRAWERS.

The Mounting Assembly may be cleaned with most mild, non-abrasive solutions commonly used in the hospital environment (e.g., diluted bleach, ammonia, or alcohol solutions). The surface finish will be permanently damaged by strong chemical and solvent such as acetone and trichloroethylene. Steel wool or other abrasive material should never be used. Damage caused by the use of unapproved substances or processes will not be warranted. It is recommended that you test any cleaning solution on a small area of the SmartDrawers that is not visible to verify compatibility. Never submerge the SmartDrawers and do not allow liquids to enter them. Wipe any cleaning agents off the SmartDrawers immediately using a water-dampened cloth. Dry the SmartDrawers thoroughly after.

Warranty Policy – SmartDrawers

Amico Accessories Inc. warrants all mounting accessories and electrical systems to be free from defects in material and workmanship for a period of twelve (12) months from the date of shipment. Within this period Amico Accessories Inc. will repair or replace any part which is proven to be defective.
Amico Accessories Inc. will warrant its mechanical materials to be free from defect for an additional period of four [4] years, (five [5] years from the date of shipment), and electrical materials to be free from defect for an additional period of two (2) years (three
[3] years from the date of shipment), except for SLA or any Hot Swap battery which is not manufactured by Amico Accessories Inc. Within this period, Amico Accessories Inc. will replace any part at no charge, which is proven to be defective. Shipping and
Installation costs after the first twelve (12) months will be borne by the customer.
This warranty is valid only when the product has been properly installed according to Amico Accessories Inc. specifications, used in a normal manner and serviced according to factory recommendations. It does not cover products that are not manufactured by Amico Accessories Inc. It does not cover failures due to damage which occurs in shipments or failures which resulted from accidents, misuse, abuse, neglect, mishandling, alteration, misapplication or damage that may be attributable to acts of God.
Amico Accessories Inc. shall not be liable for incidental or consequential damages resulting from use of equipment.
All claims for warranty must first be approved by Amico Accessories Inc. A valid Return Goods Authorization (RGA) number must be obtained from Amico Accessories Inc. prior to commencement of any service work. Warranty work, which has not been  preauthorized by Amico Accessories Inc., will not be reimbursed.

AMICO ACCESSORIES INC. DOES NOT HONOR VERBAL STATEMENTS CONCERNING THE WARRANTY.
The distributor and/or dealer are not sanctioned to create verbal warranties about the product described in this agreement. Any statements will not be honored or be made part of the agreement of sale. This document is the final complete and exclusive terms of the agreement.

THIS WARRANTY IS INCLUSIVE AND REPLACES ALL OTHER WARRANTIES.
Amico Accessories Inc. shall not, under any circumstances be liable for incidental or consequential damages including, but not limited to, profit, loss of sales or injuries to person(s) or property. Correction of noncompliance as noted above will result in completion of all liabilities of Amico Accessories Inc., whether based on agreement, neglect or changed materials, designs or specifications without notice.
All claims for warranty must first be approved by Amico Accessories Inc. Service Department: accessories@amico.com or 1.877.264.2697. A valid Return Goods Authorization number must be obtained from Amico Accessories Inc. prior to commencement of any warranty claim.

www.amico.com

AA-IM-MOBILE-COMPUTER-WORKSTATION-HUMMINGBIRD-SMARTDRAWERS 01.16.2024
Amico Accessories Inc. | 122 East Beaver Creek Road, Richmond Hill, ON L4B 1G6, Canada
Toll Free Tel: 1.877.264.2697 | Tel: 905.763.7778 | Fax: 905.763.8587
Email: info@amico-accessories.com | www.amico.com

References

• Accessories.com is for sale | www.plmp.com
• Amico Group of Companies | Home Page

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>