SILVER CREST SHBS 3.7 E1 Hair and Beard Trimmer Instruction Manual
- August 14, 2024
- SILVER CREST
Table of Contents
SILVER CREST SHBS 3.7 E1 Hair and Beard Trimmer
Product Specifications
- Model: HAIR & BEARD TRIMMER SHBS 3.7 E1
- Model Number: IAN 444777_2307
- Power Source: Battery/Rechargeable
- Safety Class: Class III
Charging the Product
Before first use, ensure the product is fully charged by connecting it to a power source using the provided charger. Allow sufficient time for charging.
Before First Use
Prior to using the trimmer, make sure it is clean and dry. Check the blades for any damage and ensure they are properly aligned.
Oiling the Blades
Regularly oil the blades to maintain their sharpness and ensure smooth operation. Apply a few drops of oil to the blades and run the trimmer for a few seconds to distribute the oil.
Operation
Turn on the trimmer using the ON/OFF button. Adjust the cutting length if necessary and start trimming your hair or beard in the desired style.
Cleaning and Care
After each use, clean the trimmer by removing any hair clippings and debris. You can use a brush or a cleaning tool provided with the product. Avoid water contact with the main unit.
Storage
Store the trimmer in a dry and safe place, away from moisture and direct sunlight. Keep it in a protective case if available to prevent any damage.
FAQs
How often should I oil the blades?
It is recommended to oil the blades after every few uses or when you notice
a decrease in cutting performance.
Can I use the trimmer in the shower?
No, this trimmer is not waterproof. Avoid exposing it to water to prevent
damage to the unit.
How do I adjust the cutting length?
Refer to the user manual for specific instructions on adjusting the cutting
length of the trimmer according to your desired style.
“`
List of pictograms used Read the instruction manual Observe the warnings and safety information! Volt Safety information Instructions for use Protection class III ON/OFF button
USB type C connector
For indoor use only
Direct current/voltage
Hair & beard trimmer
Introduction
We congratulate you on the purchase of your new product. You have chosen a high quality product. The instructions for use are part of the product. They contain important information concerning safety, use and disposal. Before using the product, please familiarise yourself with all of the safety information and instructions for use. Only use the product as described and for the specified applications. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it.
Intended use
This product is only intended for cutting human hair. Only use the product on
dry hair. This product is only intended for private household use and must not
be used for commercial purposes. The product may only be used indoors. All
other uses are considered improper and can lead to property damages or
personal injuries. The manufacturer accepts no liability for damages caused by
improper use.
DANGER OF DAMAGE TO PROPERTY! Do not use the product on artificial hair or
animal hair. Verify the product is complete and undamaged immediately after
unpacking. Only use OEM parts. Do not place the product on hot surfaces, near
hot surfaces or near an open fire. To prevent impermissible heating during use
and charging, do not cover the USB Type A to C cable, the power supply and the
product. Do not use any corrosive or abrasive cleaning agents.
To charge the rechargeable battery, use only a Class II power supply (not
included in delivery)
CE mark indicates conformity with relevant EU directives applicable for this
product.
approved for use with household appliances. SELV output: DC 5V, max. 1A.
Parts description
1 Adjustable comb attachment (3/4/5/6 mm) for the beard trimming attachment
2 Comb attachments (3/6/9/12 mm) for the hair trimmer attachment
3 Comb attachment with dial (110 mm) for the hair trimmer attachment
4 Shaving attachment (for shaving hairlines) 5 Precision trimmer attachment 6
Nose/ear hair trimmer attachment 7 Hair trimmer attachment 8 Beard trimmer
attachment 9 Hair and beard trimmer unit 10 Release button (for switch for
cutting length fine tuning (1/2/3)) 11 ON/OFF button 12 Battery symbol 13 Plug
symbol 14 Lock symbol 15 USB Type A connector 16 USB Type A to C cable 17 USB
Type C connector 18 USB Type C socket 19 Scissors 20 Blade oil 21 Cleaning
brush 22 Barber comb 23 Storage bag
Technical data
Hair & beard trimmer: HG11011
Input:
5V , 1A
Battery:
1 x 3.7 V Li-Ion, 500 mAh
6 GB
Emissions sound pressure level: Protection class:
<70 dB(A), K=3 dB(A) III/
Scope of delivery
1 Hair and beard trimmer unit 1 Precision trimmer attachment 1 Nose/ear hair
trimmer attachment 1 Hair trimmer attachment 1 Shaving attachment 1 Adjustable
comb attachment (3/4/5/6 mm) for beard
trimming attachment 4 Comb attachments (3/6/9/12 mm) 1 Adjustable comb
attachment 110 mm for hair trimmer
attachment 1 USB Type A to C cable 1 Scissors 1 Blade oil 1 Cleaning brush 1
Barber comb 1 Storage bag 1 Set of instructions
Safety notes
DANGER TO LIFE AND RISK OF ACCIDENTS FOR INFANTS AND CHILDREN! Never leave
children unattended with the packaging material or the product. There
is a danger of suffocation.
This product may be used by
children aged 8 years and up, as
well as by persons with reduced
physical, sensory or mental ca-
pacities, or those lacking expe-
rience and/or knowledge, as
long as they are supervised or
instructed in the safe use of the
product and they understand the
associated risks. Do not allow children to play with the product. Never allow
children to clean or maintain this product unsupervised.
Detach the hand-held part from the USB Type A to C cable 16 before cleaning it
in water.
Avoid the risk of fatal injury from electric shock
Keep the product dry.
Do not use this product near bathtubs, showers, basins or other vessels
containing water.
If the product falls into the water, immediately remove the USB Type A to C
cable 16 from the power supply (not included in delivery) before you reach
into the water.
Never touch the USB Type A to C cable 16 with moist or wet hands, especially
when you plug it into the socket or pull it out of the socket.
Never submerge the product or the USB Type A to C cable 16 in water
GB 7
or any other liquid and never rinse this/these under running water.
Do not use the product while bathing. For additional protection, the
installation of a residual current device (RCD) having a rated residual
operating current not exceeding 30 mA is advisable in the electrical circuit
supplying the bathroom.
Ask your installer for advice. Remove the USB Type A to C cable 16 from the
power supply (not included in delivery) – if a malfunction occurs, – before
you clean the product, – if you have not used the product for a long time, –
during a thunderstorm and – after each use. When doing so, remove the USB Type
A connector 15 directly from the socket and do not pull it out using the USB
Type A to C cable 16 .
Avoid risk of injury
Do not change the accessories while the product is switched on. Do not use the
product if you detect any kind of visible, external
damage. Never use a damaged product. If liquid gets into the product, check before using the product once more. If you notice that the USB Type A to C cable 16 , housing or another part has become damaged, the product can no longer be used. Repairs should only be carried out by a specialist. Improper repairs may result in considerable danger to the user. This will also make any warranty claims void. Do not use defective attachments with the product as these could have sharp corners. Defective components must always be replaced with original spare parts. Only by using original spare parts can you ensure that safety requirements are met. For loading connect the USB Type A to C cable 16 to a power supply which is well within reach. Never use the product unsupervised and only use it in accordance with the information stated on the type plate. Connect the USB Type A to C cable 16 to the product before inserting it into the power supply.
8 GB
The tips of the attachments are sharp. Switch off the product before attaching
or switching the attachments, as well as before cleaning. Lay the USB Type A
to C cable 16 so nobody will step on or trip over it. Do not use the product
if you have an open wound, cut, sunburn or blister.
Avoid the danger of damage to property
Electrical products may pose a hazard to animals. Animals can also damage the product. Always keep animals away from electrical products. Protect the product from moisture, drops of water and splashing water. Ensure that the USB Type A to C cable 16 does not get stuck in cupboard doors and that it is not pulled over hot surfaces. This could damage the USB Type A to C cable 16 insulation. Use the original accessories only. Do not place the product on hot surfaces, near hot surfaces or near an open fire.
To prevent impermissible heating do not cover the power supply and the product
during use and charging. Do not use any corrosive or abrasive cleaning agents.
Keep the blade oil 20 out of reach of children. Do not ingest the blade oil
20, do not get it into your eyes. Keep it in a safe place if it is not being
used. ATTENTION! Risk of product damage! Do not expose the product to direct
sunshine or heat. The ideal ambient temperature is between +5 and +40 °C.
Extreme low or high temperature may damage the battery or the product.
Safety instructions for batteries/ rechargeable batteries
For the purpose of recharging the batteries, only use protection class II
power supply (not provided) approved for use with household product. SELV
output: DC 5V, max. 1A. DANGER TO LIFE! Keep batteries/rechargeable batteries
out
GB 9
of reach of children. If accidentally swallowed seek immediate medical
attention.
DANGER OF EXPLOSION! Never recharge non-rechargeable batteries. Do not short-
circuit batteries/rechargeable batteries and/or open them. Overheating, fire
or bursting can be the result. Never throw batteries/rechargeable batteries
into fire or water. Do not exert mechanical loads to batteries/rechargeable
batteries.
Risk of leakage of batteries/ rechargeable batteries
Avoid extreme environmental conditions and temperatures, which could affect
batteries/ rechargeable batteries, e.g. radiators/direct sunlight. If
batteries/rechargeable batteries have leaked, avoid contact with skin, eyes
and mucous membranes with the chemicals! Flush immediately the affected areas
with fresh water and seek medical attention!
WEAR PROTECTIVE GLOVES! Leaked or damaged batteries/rechargeable batteries can
cause burns on
contact with the skin. Wear suitable protective gloves at all times if such an event occurs. This product has a built-in rechargeable battery which cannot be replaced by the user. This product contains a battery which is non- replaceable. When disposing of the product, it should be noted that this product contains a rechargeable battery.
Charging the product
Note: Charge the product for 90 minutes before using it for the first time and
subsequent charging. Note: Connect the USB Type C connector 17 to the USB type
C socket 18 on the product. Connect the USB Type A connector 15 of the USB
type A to C cable 16 to a suitable USB Type A socket of a protection class II
power supply (not provided), that is approved for use with household products
and has a SELV output of DC 5V, max. 1A. Connect the mains adapter (not
provided) to the socket. Note: The plug symbol 13 will flash red when the
battery is nearly drained. Note: In order to lengthen the service life of the
rechargeable battery, it is recommended that the product is used regularly and
without long storage periods. Note: After a quick charge for 5 minutes the
product can be used for approx 3 minutes. Note: When the battery is fully
charged, the battery symbol
12 flashes in white. When the battery is fully charged, the product can be
used for approx. 60 minutes without being connected to the power supply.
Before first use
DANGER OF ELECTRIC SHOCK! The hair and beard trimmer is not waterproof and
therefore must not be used in the bathtub/shower.
Please do not use the product if you have an open wound, cut, sunburn or
blister. The product is only intended for use on dry hair in dry, indoor
spaces. The product can be used cordless only.
10 GB
Oiling the blades
It is recommended that you oil the blades before first use and after cleaning
to guarantee complete functionality (see Fig. G, H, I).
Always switch off the product before oil the blade. Apply one or two drops of
blade oil 20 between the blades and distribute them evenly. Wipe off any
excess oil with a cloth. You can also use any acid-free oil (such as sewing
machine oil).
Transport lock
The lock symbol 14 flashes white for a short time if a key is pressed when the
transport lock is activated.
Press and hold the ON/OFF button 11 for approx. 3 seconds to
activate/deactivate the transport lock. The lock symbol 14 flashes for 3 times
and then goes out.
Operation
Note: For all applications hold the shaver with an angle of 45° to your skin
(see Fig. F).
Changing the cutting attachments 4, 5, 6, 7, 8
RISK OF INJURY! Switch off the hair and beard trimmer unit 9 , before you
attach or remove the attachments.
To attach the attachments 4 , 5 , 6 , 7 , 8 (see Fig. B), put the lower flap
of the attachment 4 , 5 , 6 , 7 , 8 into the slot in the hair and beard
trimmer unit 9 and press the upper part of the attachment against the hair
trimmer until it audibly locks into place and sits firmly in position. To
remove the attachments 4 , 5 , 6 , 7 , 8 (see Fig. A) use your thumbs to press
the attachment towards the rear of the hair and beard trimmer unit 9 .
Changing the comb attachments 1, 2, 3
To attach the comb attachments 1 , 2 , 3 carefully slide the appropriate comb
attachment over the hair or bread trimmer attachment 7 / 8 . Press the lower
part of the comb attachments 2 and 3 firmly until they lock into place. To
remove the comb attachments 2 and 3 loosen the comb attachment at its lower
end and pull it off the hair and beard trimmer unit 9 . Slide the adjustable
comb attachment 1 for the beard trimmer attachment 8 upwards from the hair and
beard trimmer unit 9 .
Cutting hair (Hair trimmer attachment 7 )
Note: The hair to be dressed must be dry. The cutting length may deviate
depending on the cutting angle.
Place a sheet or cape around throat and neck to prevent cut-off hair from
dropping into the collar. Comb the hair well with included barber comb 22.
First, start with a comb attachment 2 with a longer cutting length and then,
in the course of the cutting process, use shorter cutting lengths step by
step. With the comb attachment with dial 3 you also start with a longer
cutting length. Turn the dial anticlockwise to shorten the cutting length and
clockwise to lengthen it. (see Fig. C).
Start by cutting the hair in the neck or on the sides and cut towards the center of the head. Then, cut the front section of the hair towards the center of the head. Hold the hair and beard trimmer unit 9 in such a way that the comb attachment 2 lies as flat as possible on the head. Move the hair and beard trimmer unit 9 evenly through the hair. Hold the hair and beard trimmer unit 9 with comb attachment 3 in such a way that the flat area above the dial lies on the head (see Fig. D). Cut against direction of hair growth. In order to catch all the hair, move the hair and beard trimmer unit 9 several times through each section ofthe hair. Comb the hair repeatedly and well. Using the switch for cutting length fine tuning 10 the cutting length can be slightly varies with three levels: 1/2/3 (1.8 mm0.8 mm). In order to achieve a straight cutting line for cutting lengths, the hair and beard trimmer unit 9 should be passed through the hair several times from different directions.
Trimming a beard (Beard trimmer attachment 8 )
Note: Please note that the cutting lengths will only be achieved if the switch
for cutting length fine tuning 10 is at position 1 and the hair and beard
trimmer unit 9 is held at a right angle to the skin surface.
Comb the beard in the direction that it grows. Trim the beard downwards from
ear to chin. First trim one side, then the other. Comb attachment 1 : Adjust
the cutting length with the slider according to the desired hair length and
read off the cutting length using the marking on the side of the comb
attachment 1 (3/4/5/6 mm) (see Fig. E). Now, shorten your beard step by step.
Using the beard trimmer attachment 4 without a comb attachment 1 , to cut the
beard very short or to cut a moustache and hairline. Using the switch for
cutting length fine tuning 10 the cutting length can be slightly varied with
three levels:1/2/3 (1.8 mm0.8 mm).
GB 11
Trimming the hairline (Precision trimmer attachment 5 )
Use the precision trimmer attachment 5 to shorten and shape moustache,
whiskers, sideburns or eyebrows. Put the edge of the attachment at the desired
hairline height and move the hair and beard trimmer unit 9 downwards.
Shaving (contours) (Shaving attachment 4 )
Note: Your skin must be clean and dry. The shaving attachment 4 is only
suitable for shaving hairlines.
Hold the hair and beard trimmer unit 9 at a right angle to the skin surface
and gently guide it over your face. Shave against the direction of your beard
growth. Stretch your skin in complicated areas, such as the chin, to achieve
better results.
Trimming nose and ear hair (Nose/ear hair trimmer attachment 6 ) (see Fig. J)
Insert only the metal tip slowly into a nostril or an ear. Slowly move the
hair and beard trimmer unit 9 with a circular motion to trim the hair.
Cleaning with the cleaning brush
Switch the product off using the ON/OFF button 11 . If cutting attachments ( 4
8 ) or comb attachments ( 1 3 ) is attached on the product, remove it
before cleaning as described in the chapter “Operation”. Remove the attachment
by pressing the trimmer with your thumbs from the front (see Fig. A). Remove
the hair remnants from the attachment using the cleaning brush 21 .
Cleaning and care
Never immerse the product, the USB Type A to C cable 16 and the power supply
in water or other liquids during corded use or rinse under running water.
Always switch off the product before cleaning it. The comb attachments 1 , 2 ,
3 and nose/ear hair trimmer attachment 6 can be cleaned with water. Do not use
any other liquids. Note: Let them dry before using again. Do not use
aggressive or abrasive cleaning agents. Wipe down the product with a slightly
damp cloth. If you are not using the product for extended periods, store it in
the storage bag 23.
Hair and beard trimmer unit 9 Wipe the casing of the hair and beard trimmer
unit 9 with a damp cloth.
Comb attachments 1 , 2 , 3 Remove the comb attachment 1 , 2 , 3 . Rinse the
comb attachment 1 , 2 , 3 with water and let it dry before using again.
Precision trimmer 5 , hair trimmer 7 and beard trimmer attachments 8
Remove the attachment from the hair and beard trimmer unit 9 by pressing it with the thumb towards the rear (see Fig. A). Remove the hair remnants from the attachment using the cleaning brush 21 included in the delivery. Note: It is recommended that you oil the blades before first use and after cleaning to guarantee complete functionality (see Fig. G, H, I). Always switch off the product before oil the blade. Apply one or two drops of blade oil 20 between the blades and distribute them evenly. Wipe off any excess oil with a cloth. You can also use any acid-free oil (such as sewing machine oil). Note: The blades can be oiled with or without the comb attachment 1 , 2 or 3 .
Ordering replacement parts
Replacements for the following parts can be ordered online:
Shaving attachment 4 Precision trimmer attachment 5 Nose/ear hair trimmer
attachment 6 Hair trimmer attachment 7 Beard trimmer attachment 8
Item number: 444777_2307 Website: www.optimex-shop.com
Nose/ear hair trimmer attachment 6 Remove the nose/ear hair trimmer attachment
6 . Rinse it with water and let it dry completely before using it again.
Shaving attachment 4 Do not detach the shaving foil from the shaving foil
frame, and do not clean it using the cleaning brush 21 . Note: From time to
time, oil the cutting blade with a few drops of acid- free oil (e.g. sewing
machine oil). Attach the shaving attachment 4 to the hair and beard trimmer
unit 9 and let it run for a few seconds without using it. Using a soft cloth,
wipe off the surplus oil, if necessary. Remove the shaving attachment 4 .
Press the button on the side of the shaving attachment 4 and remove the
shaving foil frame. While removing the shaving foil frame, only hold it at the
side and do not press against the shaving foil.
12 GB
Clean the cutting blade using the included cleaning brush 21. Clean the
shaving foil in the shaving foil frame under running water and allow it to dry
completely before putting it back on the shaving attachment 4 . Put the
shaving foil frame back onto the shaving attachment 4 . While attaching the
frame, make sure that the fastening tabs on the shaving foil frame fit into
the appropriate recesses
on the shaving attachment 4 , and press the shaving foil
frame gently downwards until it audibly locks into place.
Storage
CAUTION! DANGER OF DAMAGE TO PROPERTY! Never store the product in the storage
bag 23 whilst the product is charging. Risk of overheating! Store the clean
and dry product and its accessories in the storage bag 23 provided. Store
everything in a clean, dust-free and dry place.
Troubleshooting
Error The product does not work. Trimming is difficult.
The rechargeable battery cannot be charged or the battery performance is very
poor.
Cause
Solution
The battery may not be charged.
Recharge the product.
Hair may be stuck inside the blades.
Clean the cutting unit 1 8 and the product and oil it if necessary.
The rechargeable battery has reached The product with the built-in rechargeable
the end of its service life.
battery must be properly disposed of.
Disposal
The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.
Observe the marking of the packaging materials
b
for waste separation, which are marked with ab-
a
breviations (a) and numbers (b) with following
meaning: 17: plastics/2022: paper and
fibreboard/8098: composite materials.
Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.
To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority.
This product has a built-in rechargeable battery that cannot be replaced or removed by the user. When disposing of the product, it must be noted that this product contains a rechargeable battery.
Faulty or used batteries/rechargeable batteries must be recycled in accordance with Directive 2006/66/EC and its amendments. Please return the batteries/rechargeable batteries and/or the product to the available collection points.
Environmental damage through incorrect disposal of the batteries/ rechargeable
batteries!
Batteries/rechargeable batteries may not be disposed of with the usual
domestic waste. They may contain toxic heavy metals and are subject to
hazardous waste treatment rules and regulations. The chemical symbols for
heavy metals are as follows: Cd = cadmium, Hg = mercury, Pb = lead. That is
why you should dispose of used batteries/rechargeable batteries at a local
collection point.
Warranty
The product has been manufactured to strict quality guidelines and
meticulously examined before delivery. In the event of material or
manufacturing defects you have legal rights against the retailer of this
product. Your legal rights are not limited in any way by our warranty detailed
below.
The warranty for this product is 3 years from the date of purchase. The
warranty period begins on the date of purchase. Keep the original sales
receipt in a safe location as this document is required as proof of purchase.
Any damage or defects already present at the time of purchase must be reported
without delay after unpacking the product.
Should the product show any fault in materials or manufacture within 3 years
from the date of purchase, we will repair or replace it at our choice free
of charge to you. The warranty period is not extended as a result of a claim
being granted. This also applies to replaced and repaired parts.
This warranty becomes void if the product has been damaged, or used or
maintained improperly.
The warranty covers material or manufacturing defects. This warranty does not
cover product parts subject to normal wear and tear, thus considered
consumables (e.g. batteries, rechargeable batteries, tubes, cartridges), nor
damage to fragile parts, e.g. switches or glass parts.
Warranty claim procedure
To ensure quick processing of your case, please observe the following
instructions:
Please have the till receipt and the item number (IAN 444777_2307) available
as proof of purchase. You will find the item number on the rating plate, an
engraving on the front page of the instructions for use (bottom left), or as a
sticker on the rear or bottom of the product. If functional or other defects
occur, please contact the service department listed either by telephone or by
e-mail. You can return a defective product to us free of charge to the service
address that will be provided to you. Ensure that you enclose the proof of
purchase (till receipt) and information about what the defect is and when it
occurred.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>