Silver Crest SLR 30 A1 AIR PURIFIER Instruction Manual

Silver Crest SLR 30 A1 AIR PURIFIER product

Introduction

Information about these operating instructions Congratulations on the purchase of your new appliance. You have selected a high quality product. The operating instructions are part of this product. They contain important information about safety, usage and disposal.
Before using the product, please familiarise yourself with all operating and safety instructions. Use the product only as described and for the range of applications specified. Please pass on all documents associated with this product to any future owner.

Copyright

This documentation is protected by copyright. Any copying or reproduction, including in the form of extracts, or any reproduction of images (even in a modified state), is permitted only with the written authorisation of the manufacturer.

Proper use

This appliance is designed exclusively for air purification in indoor rooms. It is not intended for any other purpose nor for use beyond the scope described. The appliance is not intended for use in commercial or industrial environments. The manufacturer accepts no responsibility for damage caused by failure to observe these instructions, improper use or repairs, unauthorised modifications or the use of unapproved replacement parts. The operator bears sole liability.

Safety information
RISK OF ELECTRICAL SHOCK

• Connect the appliance only to mains power sockets supplying a mains power voltage of 220–240 V ∼, 50 Hz.
• Always pull on the plug to disconnect the appliance from the mains.
• Do not pull on the cable itself.
• Do not kink or crush the power cable, and route the cable so that it cannot be stepped on or tripped over.
• To avoid risks, arrange for defective plugs and/or power cables to be replaced at once by qualified technicians or our Customer Service Department.
• Ensure that the power cable does not become wet or damp during use.
• Route the cable in such a way that it cannot be caught or damaged.
• In case of a malfunction, remove the plug from the socket.
• Pull out the plug from the mains power socket before cleaning the appliance or changing accessories.
• Operate the appliance only with dry hands and never without shoes i.e. not barefoot.
• This will help reduce the effect of an electric shock in the event of a malfunction.
• Never immerse the appliance in water or other liquids.
• Use the appliance only in indoor areas, not outdoors.

RISK OF INJURY

• Use only the original accessory parts recommended by the manufacturer for this appliance.
• Only use the appliance when it is properly and completely assembled.
• The appliance may not be used if it has been dropped, if there are any obvious signs of physical damage or if it is leaking.
• Always pull the plug out of the power socket during each break in use, as well as after use and before any cleaning.

ATTENTION! PROPERTY DAMAGE

• Do not insert any objects into the openings of the appliance.
• Do not use the appliance if the openings are blocked. Keep the openings free of dirt, fluff, hairs or anything that could impede the air circulation.
• Ensure that the appliance, the power cable and the plug do not come into contact with heat sources such as hotplates or naked flames.
• Never leave the appliance unattended during operation.

Basic safety instructions

To ensure safe operation of the appliance, follow the safety guidelines set out below

• Check the appliance for visible external damage before use. Do not operate an appliance that has been dam-aged or dropped.
• During operation, always keep windows and doors closed so that the appliance can work effectively.
• Do not operate the appliance in the proximity of highly flammable gases or materials, near naked flames or in areas prone to oil and water splashing.
• This appliance may be used by children aged 8 years and above and by persons with limited physical, sensory or mental capabilities or lack of experience and knowledge, provided that they are under supervision or have been told how to use the appliance safely and are aware of the potential risks.
• Do not allow children to play with the appliance.
• Do not allow children to carry out cleaning and user maintenance tasks unless they are supervised.
• All repairs must be carried out by authorised specialist companies or Customer Service.
• Improper repairs can pose significant risks to the user.
• This appliance should not be exposed to rain.
• Protect the appliance from moisture and do not allow any liquids or objects to get inside the housing.
• Do not place any liquid- filled containers e.g. flower vases on the appliance.
• The appliance could be irreparably damaged!
• Do not place any heavy objects on the appliance.
• Do not cover the appliance (e.g. with newspapers, cushions or blankets).
• Avoid direct sunlight.
• Do not place any naked flames, e.g. burning candles, on or directly next to the appliance.
• In the event of malfunctions  and during thunderstorms  disconnect the plug from the mains power socket.
• Set up the appliance on a solid, flat and dry surface so that it cannot tip over.
• Place the appliance at a minimum distance of 20 cm from walls or other objects.
• A minimum distance of 50 cm must be maintained above the appliance to ensure good air circulation.
• The appliance may only be operated in rooms with an ambient temperature of 5°C to 35°C.
• Use the appliance in rooms with a maximum area of 15 m² and a maximum height of 2.4 m.

Package contents and transport inspection

Remove all parts of the appliance and the operating instructions from the carton. Remove all packaging materials and any films and labels.

ATTENTION! PROPERTY DAMAGE

The filter 8 inside the appliance is additionally packed in a plastic bag. Before starting up the appliance, remove this plastic bag from the filter 8 (see section Changing the filter. Check the contents of the package. The package contents include the following components (see fold-out page for illustrations

• Air purifier
• Filter (in the appliance
• Operating instructions

NOTE
Check the package for completeness and signs of visible damage. If the delivery is incomplete or damage has occurred as a result of defective packaging or during transport, contact the Service hotline.

Appliance description

• 1 Control panel
• 2 Timer button
• 3 Filter change button
• 4 On/Off button
• 5 Air outlets
• 6 Housing
• 7 Air inlets
• 8 Filter
• 9 Housing cover (underside of appliance)
• 0 Power cable connection (rear of appliance)
• q Particle sensor compartment cover (rear of appliance) w Illuminated ring
• e Ion function button
• r Fan function button

Handling and operation

• Never cover the ventilation openings, as this may cause the appliance to overheat. When setting up the appliance, maintain a sufficient distance from walls or other objects.
• Place the appliance on a firm, level and dry surface.
• The appliance is designed for use in rooms up to a maximum size of 15 m² and with a maximum height of 2.4 m (maximum room volume36m
• The appliance may emit a slight plastic odour during first use.
• This will dissipate after a certain period of operation. This smell is due to the materials used in the manufacture of the appliance and is not harmful to health.

How the appliance works

Inside the air purifier, there is a fan (ventilator) which draws the air in the room into the appliance and then through a high-quality filter. The filter cleans the air of particles such as house dust, pollen, fungal spores, smoke etc., so that the amount of these particles in the air is reduced. In addition, the activated carbon filter contained in the filter ensures that odours in the air are neutralised or reduced. The appliance has a timer function for automatic switch-off and a sleep mode for silent fan operation during the night. The additional ion function allows efficient removal of dirt particles in the air, thus improving indoor air quality.

Ion function

The ion function is used to electrically charge ionise particles (atoms or molecules) contained in the air in the air purifier. These ions are then released into the room air via the fan. As a result, airborne ions and particles with different charges stick together. These particles sink more easily and can therefore no longer float around in the room air.

Air quality indicator illuminated ring

There is an illuminated ring w on the appliance’s control panel 1, which uses different colours to indicate the amount of dirt particles in the room air.
Depending on the quality of the room air, the illuminated ring w lights up in one of the following colours

Button functions

The following table explains the functions of the buttons on the appliance control panel 1

Switching the appliance on/off

Insert the mains plug of the appliance into a mains socket. You will hear a beep and all the buttons and indicators on the control panel 1 will light up briefly. The appliance is now in standby mode. In standby mode, the On/Off button 4 lights up continuously. Briefly press the On/Off button 4 to switch the appliance on. You will hear a beep and the active buttons and indicators on the control panel 1 will light up. To switch the appliance into standby mode, briefly press the On/Off button 4 again. You will hear a beep and all the buttons and indicators on the control panel 1 apart from the On/Off button 4 switch off.

Appliance functions

Ion function

During operation, briefly press the ion function button e, to switch on the ion function. The ion function button e lights up. Press the ion function button e again briefly to switch off the ion function. The ion function button e goes out.

Fan function

The fan function of the appliance offers you the following setting options
Sleep
Minimum fan speed for virtually silent operation and minimum airflow. The illuminated ring w is switched off in this setting.
Low
Low fan speed for low air flow
High
High fan speed for high air flow
Auto
Automatic adjustment of the fan speed and thus the air flow rate depending on the current air quality.

If necessary, briefly press the fan function button r several times during operation to select the desired setting (Sleep, Low, High, Auto). The selected setting is displayed on the control panel 1 and the fan function button r lights up.
NOTE
The standard setting for the fan function is Auto. The ion function cannot be activated in the Sleep setting

Timer function

You can use the timer function to set the operating time of the appliance to between 1, 2, 4 or 8 hours. After the set operating time has elapsed, the appliance turns off automatically and switches to standby mode. To set the timer function, proceed as follows

• During operation, briefly press the timer button 2 once to activate the timer
  function.

• Then press the timer button 2 briefly, several times if necessary, to set the required operating time 1 hr, 2 hrs, 4 hrs, 8 hrs.

• The set operating time is displayed on the control panel 1 and the timer button 2 lights up.

• To deactivate the timer function, press the timer button 2 briefly several times if necessary during operation until the operating time display (1 hr, 2 hrs, 4 hrs, 8 hrs) goes out and the timer button 2 is no longer illuminated.
  NOTE
  When the appliance is switched off, the last selected settings of all functions are saved. These are then used when the appliance is switched on again. If you disconnect the appliance from the power supply, the last selected settings are deleted.

Cleaning and maintenance

Cleaning the appliance

RISK OF ELECTRICAL SHOCK
Switch the appliance off and pull out the mains plug before cleaning the appliance

ATTENTION! PROPERTY DAMAGE
Do not use caustic, abrasive or solvent-based cleaning materials. These can damage the surfaces of the appliance Ƈ Clean the appliance with a dry or slightly moist cloth. For stubborn soiling, use a little mild detergent on the dampened cloth. Ƈ Clean the ventilation openings carefully and regularly with a suitable soft brush to remove dust and dirt.

Cleaning the particle sensor

RISK OF ELECTRICAL SHOCK
Before cleaning the particle sensor, always switch off the appliance and remove the mains plug from the socket.

NOTE
Clean the particle sensor once a month when using the appliance in continuous operation. If you only use the appliance occasionally, clean the particle sensor after two months at the latest.To clean the particle sensor, proceed as follow

1. Switch off the appliance and pull out the mains plug.
2. Open the particle sensor compartment cover q on the back of the appliance by placing your finger in the cover q opening.
3. Then pull the cover q towards you until it opens.

The lens of the particle sensor is located on the left. Clean it with a dry cotton swab or a soft, dry cloth. Replace the cover q into the corresponding openings in the housing 6. Press the cover q into the openings until the cover q audibly clicks into the housing 6.

Replacing the filter

RISK OF ELECTRICAL SHOCK
Always switch off the appliance and unplug it from the mains before chang- ing the filter

NOTE
The interval for a filter change is approx. 1500 operating hours.  Information on ordering replacement filters can be found in the next section

Ordering spare parts.

When the filter 8 has reached the end of its life and is used up, this is indicated by the flashing of the filter change button 3. To change the filter 8 and replace it with a new filter 8, proceed as follows

1. Switch off the appliance and pull out the mains plug.
2.  Turn the appliance upside down to access the bottom of the unit.
3. Turn the housing cover 9 on the bottom of the appliance a little way anticlockwise in the OPEN direction to open it.
4. Then remove the housing cover 9 from the appliance.

Remove the filter 8 from the appliance and insert a new filter 8 into the appliance. Replace the housing cover 9 onto the appliance. Pay attention to the recesses on the edge of the lid opening. Turn the housing cover 9 clockwise a little way in the CLOSE direction un- til it is closed. Turn the appliance back over. Press the filter change button 3 for about 3 seconds to confirm the filter change and reset the filter timer. You will hear a beep, the filter change button 3 flashes three times and then goes out.

Ordering replacement parts

You can order replacement parts for this product on the Internet at www.kompernass.com 

Scan this QR code with your smartphone or tablet. You can use this QR code to go directly to our web- site www.kompernass.com to view and order the available spare parts.

NOTE
If you have problems with your online order, you can contact our service centre by phone or email. Please always quote the article numbere.g 123456_7890 when ordering. You can find it on the title page of these operating instructions. Please note that online ordering of replacement parts is not possible for all countries.

Storage

Disconnect the appliance from the power supply by pulling the plug of the switched-off appliance from the socket. Store the appliance in a dry and dust- free location out of direct sunlight.

Troubleshooting

The following table will help you to identify and rectify minor malfunctions. If the solutions presented below do not resolve the problem, please contact Customer Service.

Disposal

Disposal of the appliance

The adjacent symbol of a crossed-out wheelie bin means that this appliance is subject to Directive 2012/19/EU. This directive states that the product may not be disposed of in normal household waste at the end of its useful life, but must be taken to a specially set-up collection point, recycling depot or disposal company. This disposal is free of charge for the user. Protect the environ- ment and dispose of this appliance properly. Your local community or municipal authorities can provide information on how to dispose of the worn out product. The product is recyclable, subject to extended producer responsibility and is collected separately.

Disposal of the packaging

The packaging materials have been selected for their environmental compatibility and ease of disposal, and are therefore recyclable. Dispose of packaging materials that are no longer needed in accordance with applicable local regulations. Dispose of the packaging in an environmentally friendly manner. Note the labelling on the packaging and separate the packaging material com- ponents for disposal if necessary. The packaging material is labelled with abbreviations (a) and numbers (b) with the following meanings

• 1–7: plastics,
• 20–22: paper and cardboard, 80–98: composites.

Appendix

Technical data

Kompernass Handels GmbH warranty
Dear Customer,
This appliance has a 3-year warranty valid from the date of purchase. If this product has any faults, you, the buyer, have certain statutory rights. Your statutory rights are not restricted in any way by the warranty described below.

Warranty conditions
The warranty period starts on the date of purchase. Please keep your receipt in a safe place. This will be required as proof of purchase. If any material or manufacturing fault occurs within three years of the date of pur- chase of the product, we will either repair or replace the product for you or refund the purchase price at our discretion. This warranty service requires that you pres- ent the defective appliance and the
proof of purchase (receipt) within the three year warranty period, along with a brief written description of the fault and of when it occurred. If the defect is covered by the warranty, your product will either be repaired or replaced by us. The repair or replacement of a product does not signify the be ginning of a new warranty period.

Warranty period and statutory claims for defects
The warranty period is not prolonged by repairs effected under the warranty. This also applies replaced and repaired components. Any damage and defects present at the time of purchase must be reported immediately after unpacking. Re pairs carried out after expiry of the warranty period
shall be subject to a fee.

Scope of the warranty
This appliance has been manufactured in accordance with strict quality guide- lines and inspected meticulously prior to delivery. The warranty covers material faults or production faults. The warranty does not extend to product parts subject to normal wear and tear or to fragile parts which could be considered as consumable parts such as switches, batteries or parts made of glass. The warranty does not apply if the product has been damaged, improperly used or improperly maintained. The directions in the operating instructions for the product regarding proper use of the product are to be strictly followed. Uses and actions that are discouraged in the operating instructions or which are warned against must be avoided. This product is intended solely for private use and not for commercial purposes. The warranty shall be deemed void in cases of misuse or improper handling, use of force and modifications / repairs which have not been carried out by one of our authorised Service centres.

Warranty claim procedure
Please have the till receipt and the item number (e.g. IAN 123456_7890) available as proof of purchase. You will find the item number on the type plate on the product, an engraving on the product, on the front page of the operating instructions (below left) or on the sticker on the rear or bottom
of the product. If functional or other defects occur, please contact the service department listed either by telephone or by e-mail.  You can return a defective product to us free of charge to the service address that will be provided to you. Ensure that you enclose the proof of purchase (till receipt) and information about what the defect is and when it occurred.

You can download these instructions along with many other manuals, product videos and installation software at www.lidl-service.com This QR code will take you directly to the Lidl service page www .lidl-service.com where you can open your operating instructions by entering the item number
(IAN) 359280_2007.

Service

Service Great Britain

• Tel.: 0800 404 7657
• E-Mail: kompernass@lidl.co.uk
• Service Ireland
• Tel.: 1890 930 034
• (0,08 EUR / Min., (peak)
• (0,06 EUR / Min., (off peak)) E-Mail: kompernass@lidl.ie
• IAN 359280_2007

Importer
Please note that the following address is not the service address. Please use the service address provided in the operating instructions. KOMPERNASS HANDELS GMBH BURGSTRASSE 21 44867 BOCHUM GERMANY www.kompernass.com

References

• Kompernaß - Online shop for accessories and spare parts
• de/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>