ASEPT McCormick 300400 Mustard Dispenser User Manual

: August 9, 2024
: ASEPT

Table of Contents

ASEPT McCormick 300400 Mustard Dispenser
Product Usage Instructions
FAQ
UNI Dispensers
Safety
Pump Cleaning
Assembly
Tips & Troubleshooting
ASEPT General Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ASEPT McCormick 300400 Mustard Dispenser

ASEPT-McCormick-300400-Mustard-Dispenser-product

Specifications:

Product Name: UNI Dispensers Complete Pump 9851
Components: Natural Dome 7299, Pump Housing 9720, Dome Clip7868, Valve 9683, Brush 7615, Nozzle 8651
Attachment: Pumps attach to 16mm fitments in pouches
Cleaning: All pump components are dishwasher-safe

Product Usage Instructions

Safety and Cleaning:

All components must be cleaned before first use. Clean, rinse, sanitize, and dry parts at least every 24 hours. Follow local sanitization requirements.

Pump Cleaning:

Disassemble all parts. Clean with soap and hot water, rinse, sanitize, and dry according to local requirements.
Use the supplied brush for scrubbing inside parts.

Assembly:

Mount the nozzle onto the pump housing.
Insert dome into the pump housing and secure with dome clip.
Insert valve into the pump housing.

Connecting Pump to Pouch:

Place new pouch on a countertop with the fitment facing up.
Connect the pump to the pouch by firmly pushing until it snaps into place.
Prime the pump by holding the pouch up and pushing the dome.

Dispenser Assembly:

Insert the pouch and pump into the dispenser shroud.
Insert the lid ensuring it snaps into place both front and back.

Priming Pump and Portion Setting:

Prime the pump by pressing the lever several times until food is visible in the discharge tube.
Adjust portion settings by following the provided instructions.

Tips & Troubleshooting:

If product is not dispensing, ensure proper priming of the dome.
To prevent leaks, ensure the dome is fully inserted into the pump housing.
Make sure you hear a CLICK when attaching the pump to the pouch.

FAQ

Q: How often should I clean the pump components?
- A: Clean, rinse, sanitize, and dry parts at least every 24 hours. Always comply with local sanitization requirements.
Q: How do I adjust the portion settings of the pump?
- A: Follow the provided instructions to set the desired portion size by aligning holes on the handle and link arms with holes forthe chosen portion setting

INSTRUCTION VIDEO

Models

300400 – French’s® Mustard Dispenser-US
300401 – French’s® Ketchup Dispenser-US
300402 – Old Bay® Hot Sauce Dispenser-US
300406 – Frank’s RedHot® Buffalo Wings Sauce Dispenser-US
300407 – Cattlemen’s® Memphis Sweet BBQ Sauce Dispenser-US
300408 – French’s® Mustard Dispenser-Canada (910012415)
300409 – French’s® Ketchup Dispenser-Canada (910012404)
300410 – Frank’s RedHot® Buffalo Wings Sauce Dispenser-Canada (910012405)

UNI Dispensers

Complete Pump 9851

$ASEPT-McCormick-300400-Mustard-Dispenser-fig $1$$

Designed for use with standard 1½ gallon pouched condiments and toppings. Pumps attached to 16mm fittments in pouches.

Safety

All components must be cleaned before first use. According to food and safety regulations, most foods must be stored and/or served at certain temperatures or they could become hazardous. Check with local food and safety regulators for specific guidelines. Be aware of the product you are serving and the temperature the product is required to maintain.

IMPORTANT Clean, rinse, sanitize, and dry parts at a minimum of every 24 hours. Always comply with local sanitization requirements

Pump Cleaning

Disassemble all five (5) parts. Clean with soap and hot water, rinse, sanitize and dry parts according to local sanitization requirements. Use supplied brush to scrub inside parts.

All pump components are dishwasher safe. $ASEPT-McCormick-300400-Mustard- Dispenser-fig $2$$

Clean and sanitize the exterior of shroud as needed.

NOTE: SHROUD ISNOT DISHWASHER SAFE

Assembly

Mount the nozzle onto the end of the pump housing. Bend the outer portion of the nozzle inside out. Insert into opening. Tab of nozzle faces towards housing. Flip the outer portion of the nozzle over the end of tube.
Insert dome into the pump housing. Ensure the ˛aps slide into place.Press the entire dome ÿrmly, including the top portion.
Insert the dome clip over the dome and pump housing. Ensure that the tab on bottom of the dome slides into the opening in the dome clip.
Insert the valve into the bottom of the pump housing. Wrap the ˛aps on the side of valve onto the pair of pegs on the pump housing.
TIP: Lubricate parts with clean water to ease ÿtting.
Connect the pump to pouch Put new pouch on the countertop with ÿtment facing up. Place the piercing end of connector in center of the ÿtment. Push ÿrmly until pump snaps into place. Hold pouch up and push dome to prime pump.
Insert the pouch and pump into the dispenser shroud. Hold end of pouch up while guiding the pump into the slots inside the front of dispenser.
Insert the lid Hold the lever up while inserting lid tabs into slots in back of the dispenser shroud. Make sure lid SNAPS into place front and back.
NOTE: To remove lid, hold by handle and lift lid straight up.
Prime pump
Press the pump lever several times until food is visible in discharge tube . $ASEPT-McCormick-300400-Mustard-Dispenser-fig $10$$

Tips & Troubleshooting

Product not dispensing?

Make sure dome is primed properly.

Prevent leaks:

Ensure that dome is pushed fully into pump housing. Ensure that you hear a CLICK when attaching pump to pouch.

Setting the Portion
- NOTE: Pump comes pre-set to dispense 1oz portion.
Remove locking washer
Use a head screwdriver to pry the locking washer from the pin at the end of the link arms. Keep locking washer for step 4.
Remove pin
Slide the pin out from the pair of link arms and handle holes. $ASEPT-McCormick-300400-Mustard-Dispenser-fig $12$$

Select portion setting

Align holes on handle and link arms with holes for desired portion setting. Slide pin through all. Secure pin with locking washer.

ASEPT General Warranty

Liability for defects

Should the products, as delivered, within one (1) year from delivery be shown to be defective due to defaults in material or manufacturing (“Warranty Period”), the Supplier undertakes, at its own option (i) to make a replacement delivery, (ii) to repair or rework the products claimed to be defective or (iii) to accept return of such product and refund such proportion of the purchase sum received as corresponds to the returned products. The Supplier assumes no liability for defects as regards to layout and design of the products, unless expressly stated in the Agreement. The Customer shall without undue delay notify the Supplier in writing of any defect which appears. Such notice shall under no circumstances be given later than two (2) weeks after the expiry of the Warranty Period. The Supplier is liable only for defect which appear under the conditions of operation provided for in the Agreement and under proper use of the product. The Supplier’s liability does not cover defect which are caused by faulty maintenance, incorrect use or faulty repair by the Customer, or by alterations carried out without the Supplier’s consent in writing. Finally, the Supplier’s liability does not cover normal wear and tear or deterioration. Except as expressly speciÿed above, the Supplier has no liability for defects in the products whatsoever and are under no circumstances responsible for any direct or indirect losses, damages or costs incurred by the Customer, including consequential damages. General limitation of liability Notwithstanding any other limitation of liability mentioned in the Agreement including these Terms and Conditions, the Supplier’s liability for damages under the Agreement shall be limited to the insurance compensation that can be obtained in accordance with the Supplier’s each valid liability insurance. Consequential losses There shall be no liability of either party towards the other party for loss of production, loss of proÿt, loss of use, loss of contract or for any other consequential or indirect loss whatsoever.

ASEPT International Inc.