ASEPT SS6L-1 Stainless Steel Dispensers User Manual

June 15, 2024
ASEPT

The Dispensing Specialist

ASEPT STAINLESS STEEL
DISPENSERS
User Manual

ASEPT Stainless Steel Dispensers

| Model| Part #
---|---|---
Single| SS6L-1| 10151
Double| SS6L-2| 10156
Triple| SS6L-3| 10161
Quadruple| SS6L-4| 10139
Quintuple| SS6L-5| 10291
Single Drop In| SS6L-1DI| 10266
Double Drop In| SS6L-2DI| 10271
Triple Drop In| SS6L-3DI| 10276
Quadruple Drop In| SS6L-4DI| 10281
Quintuple Drop In| SS6L-5DI| 10286

Complete Pump 10185

Designed for use with standard 1½ gallon pouched condiments and toppings.
Pumps attach to 16mm fitments in pouches.

Safety

All components must be cleaned before first use.
According to food and safety regulations, most foods must be stored and/or served at certain temperatures or they could become hazardous. Check with local food and safety regulators for specific guidelines. Be  aware of the product you are serving and the temperature the product is required to maintain.

IMPORTANT Clean, rinse, sanitize, and dry parts at a minimum of every 24 hours. Always comply with local sanitization requirements.

Cleaning

Disassemble all six (6) parts.
Clean with soap and hot water, rinse, sanitize and dry parts according to local sanitization requirements.
Use supplied brush to scrub inside parts.

All components are dishwasher safe.

Assembly

Mount the nozzle
onto the end of the pump housing.
Bend the outer portion of the nozzle inside out.
Insert into opening. Tab of nozzle faces towards housing. Flip the outer portion of the nozzle over the end of tube.

Insert dome
into the pump housing.
Ensure the flaps slide into place.
Press the entire dome firmly, including the top portion.

Insert the dome clip
over the dome and pump housing.
Ensure that the tab on bottom of the dome slides into the opening in the dome clip.

Attach hose to pump housing
Fit the holes in the hose over the pegs on the pump housing.

Attach connector to hose
Fit the bottom holes on hose over the pegs on the connector.
Piercing end of the connector must face away from pump housing.

Connect pump to pouch
Put new pouch on countertop with fitment facing up. Place piercing end of connector in center of the fitment. Push firmly until pump snaps into place.

Insert pouch and pump
into the dispenser shroud. Hold end of pouch up while guiding the pump into the slots inside the front of dispenser.

Insert the lid
Hold the lever up while inserting lid tabs into slots in back of dispenser shroud.

Prime pump
Press lever several times until food is visible in discharge tube.

Drop-In Dispensers

Add Corner Guards:
Hook first tab into slot.
Push firmly on second tab to Snap into place.

Dimensions for Cutout

| Width
(inches)| idth Depth
(inches)
---|---|---
Single| 6 3/8| 8 ½
Double| 11| 8 ½
Triple| 16 3/8| 8 ½
Quadruple| 21 13/16| 8 ½
Quintuple| 27 3/16| 8 ½

Setting the Portion

Remove locking washer
Use a flathead screwdriver to pry off the locking washer from the pin at the end of the link arms.
Keep locking washer for step 4.
Remove pin
Slide the pin out from the pair of link arms and portion holes.

Select portion setting

Align holes on link arms
with hole for desired portion setting. Slide pin through all.
Secure pin with locking washer.

ASEPT General Warranty

Liability for defects
Should the products, as delivered, within one (1) year from delivery be shown to be defective due to defaults in material or manufacturing (“Warranty Period”), the Supplier undertakes, at its own option (i) to make a replacement delivery, (ii) to repair or rework the products claimed to be defective or (iii) to accept return of such product and refund such proportion of the purchase sum received as corresponds to the returned  products. The Supplier assumes no liability for defects as regards to layout and design of the products, unless expressly stated in the Agreement.
The Customer shall without undue delay notify the Supplier in writing of any defect which appears. Such notice shall under no circumstances be given later than two (2) weeks after the expiry of the Warranty Period.
The Supplier is liable only for defect which appear under the conditions of operation provided for in the Agreement and under proper use of the product. The Supplier’s liability does not cover defect which are caused by faulty maintenance, incorrect erection or faulty repair by the Customer, or by alterations carried out without the Supplier’s consent in writing. Finally, the Supplier’s liability does not cover normal wear and tear or deterioration.
Except as expressly specified above, the Supplier has no liability for defects in the products whatsoever and are under no circumstances responsible for any direct or indirect losses, damages or costs incurred by the  Customer, including consequential damages.
General limitation of liability
Notwithstanding any other limitation of liability mentioned in the Agreement including these Terms and Conditions, the Supplier’s liability for damages under the Agreement shall be limited to the insurance compensation that can be obtained in accordance with the Supplier’s each valid liability insurance.
Consequential losses
There shall be no liability of either party towards the other party for loss of production, loss of profit, loss of use, loss of contract or for any other consequential or indirect loss whatsoever.

Tips & Troubleshooting

Prevent leaks:
Ensure that dome is pushed fully into pump housing.
Ensure that you hear a CLICK when attaching pump to pouch.
Pro Tip: Clean water may be used as lubrication when fitting hose onto pegs

Optimize pouch evacuation: Ensure ramp is in place.

Asept International Inc.
900 Oakmont Ln, Suite 207,
Westmont IL 60559, USA
+1 630-441-5656
info.us@asept.com
Asept International AB
Traktorvägen 17, SE-226 60
Lund, Sweden
+46 46 329 700
info@asept.com
www.asept.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals