EVA ELD App User Guide
- July 9, 2024
- EVA
Table of Contents
EVA ELD App
Product Information
Specifications
- Internal GPS Antenna
- Internal GSM Antenna
- OBD Connector J1939, CAN, OBD II
- 2 LED Indicators
Product Usage Instructions
Installation & Connection
Install the Eva ELD device in your vehicle
- With the engine off, locate the diagnostic port inside the vehicle.
- Attach the device to the diagnostic port of the vehicle.
- Ensure the device is working properly with a green LED light blinking after installation.
IMPORTANT: Do not place the ELD device under the dashboard to avoid interference and GPS disruption.
Install the Eva ELD App
- Download the Eva ELD App from Google Play Store for Android devices or from the App Store for iOS devices.
- Open the app and log in with your credentials provided by your Carrier administrator.
Select a Vehicle
- Log in to the Eva ELD App and select your vehicle from the list or search for it.
- Review and edit settings details on the Settings page and save your selections.
Complete Pre-Trip DVIR
- Start a new pre-trip inspection report by tapping the DVIR button in the app.
- Enter the odometer value, start the inspection, and review vehicle defects against the list.
DOT Inspection
After completing the DVIR, you can proceed with DOT inspections to ensure compliance.
Data Transfer
Ensure logs are synced and transferred as required by regulations.
Malfunction Responsibilities
Understand carrier and driver responsibilities regarding ELD malfunctions and record-keeping requirements.
FAQ
Q: What should I do if the ELD device malfunctions?
A: Refer to the ELD Malfunctions section in the user manual for troubleshooting steps. Contact support if issues persist.
Q: How do I ensure proper data transfer during DOT inspections?
A: Make sure to sync and transfer log data as per regulatory guidelines. Follow the instructions provided in the user manual for seamless data transfer.
Installation & Connection
Install the Eva ELD device in your vehicle
- With engine off, locate the diagnostic port inside the vehicle. It is located in one of the four places:
- Attach the device to the diagnostic port of the vehicle.
- Once the device is installed, ensure the device is working properly as evidenced by a green LED light blinking. The green light starts blinking after a GPS & Cellular connection is initiated.
- Securely mount your device in a location with no electrical components nearby. This will help prevent issues like ELD device interference and GPS signal disruption. It is recommended to position the ELD device visibly, ensuring an unobstructed view of the sky, as shown in the image below.
IMPORTANT: Please follow the above-mentioned instructions. Otherwise, you risk ELD device interference and GPS disruption, creating problems with the signal. Do not put an ELD device under the dashboard under any circumstances.
Install the Eva ELD App
- For android phones and tablets download the Eva ELD App from Google Play Store. For iPhones and iPads download the Eva ELD App from the App Store.
- Open the Eva ELD App.
Login to the Eva ELD App and select a vehicle
Read the login details from your email. If you don’t have login details yet, or you’ve forgotten them, contact your Carrier administrator.
- Enter your login details and tap LOG IN, you will be prompt with Terms and Conditions.
- Read the Terms and Conditions and tap AGREE.
- Select your vehicle from the list, or search for one.
- Tap ACCEPT, you will be prompt with a Settings page where you can review and edit settings details.
- Tap SAVE.
Dashboard View
After successfully login & vehicle selection, the Dashboard page is open. Use
Tap to Connect bar to connect to your vehicle.
Complete Pre-Trip DVIR
Start a new pre-trip inspection report by tapping the DVIR button.
You can also Start Inspection from the left side menu by tapping the DVIR option.
- From DVIR view, enter the odometer value and tap Start Inspection, if you are in Off Duty or Sleeper Berth status you will be placed to On Duty status. Pre-trip is selected by default.
- Tap Add/Remove under Vehicle Defects and review each item from the list against your vehicle.
- If you identify a defect, select the appropriate defect in the list and enter a comment and photo. Tap Save.
- If Trailer is applicable, repeat step 2 and 3 under Trailer Defects.
- Tap Sign and Save the Report.
Populate Log Form Data
Select Trailer/Docs button from your Dashboard to add the Trailer/Shipping Docs number.
Trailers & Shipping Docs are also available through the Logs folder.
- From your Dashboard view, tap the icon.
- Select Logs.
- Tap the daily log at the top of the list.
- Scroll down (to the bottom of the screen) and tap the Trailer or Shipping Docs field.
- Enter your trailer or shipping doc numbers. You will see “Trailer saved” OR “Shipping Docs saved” confirmation message.
Connect your mobile device to the Eva ELD device
Enable Bluetooth
Please ensure that Bluetooth is enabled on your device before you connect to
the Eva ELD device.
In the main Dashboard view there is Tap to Connect bar – just below the vehicle number
- Use Tap to Connect bar to connect to your vehicle. The device will attempt to connect to selected vehicle ELD via Bluetooth. ELD bar will change from red to orange: Pairing.
- An icon will appear in connection bar upon successful connection.
Ready to Drive
Once you’ve completed all of the pre-trip tasks in this section, you’re ready
to drive.
When your vehicle is moving at 5 MPH or greater, your duty status will
automatically switch to Driving, in accordance with the ELD mandate.
Record Hours of Service
- When your vehicle reaches 5 MPH or greater, Eva ELD is indicating that vehicle is In Motion and your duty status will automatically change to Driving.
- When the vehicle stops (0 MPH) it’s considered Stationary.
- You can change your duty status by tapping the Driving and selecting some other duty status.
- If your vehicle remains Stationary for five minutes you will be prompted with a question if you would like to change your duty status. If you ignore this question your duty status will be changed to On Duty.
DOT Inspection
Inspect Logs
To begin the DOT inspection tap the menu icon on the top left and select the DOT Inspection
- To let an officer inspect your logs tap Begin Inspection. Logs for current and last seven days will appear on the screen.
- Hand the officer your mobile device.
Data Transfer
If the officer asks for the output file tap Transfer Data
- Tap the Transfer Data to send the file via web service or email.
- Select Web Service or Email transfer method.
- A DOT officer will provide the Output File Comment, enter it in the text box.
- Tap Send.
- You will receive a confirmation if the file was submitted successfully. If it was unsuccessful, you will receive the following message:
“ELD File Sending Failed. Use a different Transfer Data method or try again.”
Malfunction Responsibilities
Carrier Responsibilities Regarding Malfunctions
The carrier must:
Provide drivers with an instruction sheet describing the various ELD malfunction events and record-keeping procedures (this document) Provide drivers with a supply of 8 days worth of blank paper driver records Repair, replace or service The motor carrier must correct the malfunction of the ELD within 8 days of discovery of the condition OR a driver’s notification to the motor carrier, whichever occurs first.
Record Keeping Responsibilities by the driver
The driver must:
Malfunction Events
Note the ELD malfunction and provide the carrier with written notice within 24
hours.
Reconstruct driving events for the current 24 hour period and previous
7 consecutive days using paper logs.
Continue to manually prepare driving logs until ELD is serviced and brought
back into compliance.
During inspections which take place when a malfunction has occurred: provide
safety official with manually kept driver logs.
Data Diagnostic Events
The driver must follow the motor carriers and ELD provider’s recommendations
in resolving the data inconsistency.
ELD Malfunctions
Diagnostic and Malfunction events show up in the application’s header (top
right) as a capital D and capital M. The D stands for diagnostic events and
the M for malfunction events.
Tap D (diagnostic data) or M (malfunction) to view error details.
Malfunction
-
ELD has reported Power compliance malfunction. Contact your manager immediately. Please stop using the Eva ELD and switch to paper logs until the ELD malfunction has been corrected.
Mon, Aug 25, 10:15 AM -
ELD has reported Engine Synchronization compliance malfunction. Contact your manager immediately. Please stop using the Eva ELD and switch to paper logs until the ELD malfunction has been corrected.
Mon, Aug 25, 10:15 AM -
ELD has reported Data Recording compliance malfunction. Contact your manager immediately. Please stop using the Eva ELD and switch to paper logs until the ELD malfunction has been corrected.
Mon, Aug 25, 10:15 AM -
ELD has reported Data Transfer compliance malfunction. Contact your manager immediately. Please stop using the Eva ELD and switch to paper logs until the ELD malfunction has been corrected.
Mon, Aug 25, 10:15 AM
Data Diagnostic
-
ELD has identified the Power data diagnostic event.
Mon, Aug 25, 10:15 AM -
ELD has identified the Engine synchronization data diagnostic event.
Mon, Aug 25, 10:15 AM -
ELD has identified the Missing required data diagnostic event.
Mon, Aug 25, 10:15 AM -
ELD has identified the Data transfer data diagnostic event.
Mon, Aug 25, 10:15 AM -
ELD has identified the Unidentified data diagnostic event.
Mon, Aug 25, 10:15 AM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>