GO RHINO RB-Series Running Board Drop Steps Instruction Manual
- June 13, 2024
- GO RHINO
Table of Contents
GO RHINO RB-Series Running Board Drop Steps
Product Information
- Product Description: RB Drop Step attachment for RB10 Running Board
- Product Safety & Legal Disclaimer: Please visit www.gorhino.com for more information.
- Manufacturer: Go Rhino
- Address: 589 W. Apollo St., Brea, CA 92821
- Contact: 888-427-4466
Product Usage Instructions
Installation Instructions:
- Before installing the product, read the installation instruction manual from front to back.
- Refer to the provided installation video or visit http://www.gorhino.com/Installation-Videos for visual guidance.
- Estimated time for installation: 30 minutes
- If you need installation service, contact the authorized distributor or call toll-free 1-888-427-4466 to find an authorized installation service company.
Tools Needed for Installation:
- 8MM SEMS Bolt
Installation Steps:
Note : The following instructions are for attaching the RB Drop Step to the RB10 Running Board on the driver side front or rear door position.
- Attach the Auxiliary Bracket to the U-Bracket using (1) 8MM SEMS Bolt. Do not tighten the screw. (Refer to Figure 1)
- Determine the desired location of the driver side RB Drop Step on the RB10 Running Board. Position (1) U-Bracket toward the front of the vehicle and the Auxiliary Bracket and U-Bracket assembly toward the rear of the vehicle in the opening on the underside of the RB10 Running Board. (Refer to Figure 2)
- Attach the driver side RB Drop Step to the RB10 Running Board using the U-Brackets and (3) 8MM SEMS Bolt. Tighten all screws securing the RB Drop Step, U-Brackets, and Auxiliary Bracket to the RB10 Running Board. Repeat steps for the passenger side. (Refer to Figure 3)
Note : The above instructions are specific to attaching the RB Drop Step to the RB10 Running Board on a Jeep Wrangler 4-door driver side rear door position.
PART NO.
- 69420000T
- 69420000PC
PRODUCT DESCRIPTION:
- Straight RB Drop Steps
PRODUCT SAFETY & LEGAL DISCLAIMER
- IMPORTANT READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY.
- Review the product package and contents prior to beginning the installation. Take care when opening the packaging and removing items. If a return is needed you will want to return the product in its original packaging if possible.
- This instruction guide is provided as a GENERAL installation guide, some vehicles vary dimensionally and may require additional steps.
- Test fit the product on the vehicle prior to any third party modifications and or finishing. The manufacturer and/or distributors do not accept responsibility for third party charges, labor and or third part replacement modifications. Some modifications may void the factory warranty.
- Exercise due-diligence when installing this product. The manufacturer and distributors of this product do not accept any responsibility for vehicle damage or personal injury resulting from the installation of this product. Careless installation and operation can result in serious injury or equipment damage.
- This product is for general off-road use. All liability for installation and use rests with the owner/operator.
- INSTALLER: Once installation is complete, please return this guide along with other documentation included in this product back to the consumer for future reference. The manufacturer/distributors of this product do not guarantee this particular version will be available at a later date.
© 2016 Go Rhino Products. All rights reserved
www.gorhino.com
589 W. Apollo St., Brea, CA 92821 P: 888 427 4466
INSTALLATION INSTRUCTIONS
INJURY HAZARD
- Please complete a shop and tool inspection prior to beginning the installation.
- Always make sure you have a clean, dry and well lit work area.
- Always remove jewelry, loose fitting clothing and wear protective gloves and eye protection.
- Always use extreme caution when jacking or raising a vehicle for work. Set the emergency brake and use tire/wheel blocks and jack stands. Refer to the vehicle manufacturer hand book. Utilize the vehicle manufacturers designated lifting points.
- Always use appropriate and adequate care in lifting parts during disassembly and installation. Seek help in lifting heavy or large items into place. Utilize jacks and or lifting devices when available.
- Always insure products are secure during disassembly and installation.
- Always wear eye protection and take steps to protect any exposed skin during the installations. Drilling, cutting and grinding plastic and metal may create flying particles that can cause injury.
- Always use extreme caution when drilling, cutting and or grinding on a vehicle. Thoroughly inspect the area to be drilled, on both sides of material, prior to modification and relocate any objects that may become damaged.
- Always assemble and tighten all fasteners per the installation instructions.
- Always route electrical cables carefully. Avoid moving parts, parts that may become hot and vrough or sharp edges.
- Always insulate and protect all exposed wiring and electrical connections.
MAINTENANCE AND CARE
- Always perform regular inspections and maintenance on mounts and related fasteners.
- Periodically check and tighten all fasteners.
- Stripped, fractured, or bent fasteners must be replaced.
- After washing the vehicle make sure to fully dry all surfaces.
- In areas with cold temperatures make sure to wash the product often to remove harmful materials used on road ways.
- Never use abrasive cleaners or polish compounds. Clean with a gentle soap and water. If you use wax use a non abrasive automotive wax such as pure carnauba wax.
WARNING
- Some products have been designed to work together with factory rear sensor systems, factory forward facing sensor systems and factory air bags.
- Installation of some of these products may alter the factory sensor system performance.
- Factory sensors may read shackles or hooks protruding from the fairlead and or tow hooks.
- All sensor testing is completed by Go Rhino Products and or third party testing labs on modified vehicles.
- Sensor sensitivity, factory sensor housing, orientation, and operating conditions are all variables that will influence functionality of the sensors.
- Installation of some product may effect the factory air bag systems.
- Some products allow the use of third party products such as winches, shackles, hooks, etc. Follow the respective manufacturers operating instructions for use with our products.
- Make sure to fully understand the product, it’s intended use and operation prior to use.
- Above all… be safe!
INSTALLATION INSTRUCTIONS
PARTS INCLUDED IN THIS LIST:
| ITEM | QTY. | DESCRIPTION |
|---|---|---|
| A | 8 | 8MM SEMS Bolt |
| B | 2 | U- Bracket |
| C | 2 | Auxiliary Bracket |
| D | 1 | Driver Straight Drop Step |
| E | 1 | Passenger Straight Drop Step |
Go Rhino recommends you, the installer, read this installation instruction manual from front to back before installing the product. You may also click here to view an installation video or visithttp://www.gorhino.com/Installation Videos.
TOOLS NEEDED FOR INSTALLATION:
½” Wrench or Socket and Ratchet
ESTIMATED TIME FOR INSTALLATION: 30 Min.
If you need installation service for your new product, call the authorized distributor from whom you purchased theproduct or an authorized installation service company which can be found by calling toll free 1 888 427 4466
Typical RB Drop Step attachment to RB10 Running Board, driver side front or
rear door position.
Step 1 Attach the Auxiliary Bracket to the U Bracket using (1) 8MM SEMS Bolt.
Do not tighten the screw, (FIGURE 1).
Typical
RB Drop Step attachment to RB10 Running Board, driver side front or rear door
position.
Step 2 Determine the desired location of the driver side RB Drop Step on the
RB10 Running Board, then position (1) U Bracket toward the front of the
vehicle and the Auxiliary Bracket and U Bracket assembly toward the rear of
the vehicle in the opening on the underside of the RB10 Running Board, (FIGURE
2).
Typical
RB Drop Step attachment to RB10 Running Board, driver side front or rear door
position.
Step 3a Attach the driver side RB Drop Step to the RB10 Running Board using
the U Brackets (3) 8MM SEMS Bolt ( FIGURE 3). Tighten all screws securing the
RB Drop Step, U Brackets and Auxiliary bracket to the R10 Running Board.
Repeat steps for the passenger side.
Typical
RB Drop Step attachment to RB10 Running Board, Jeep Wrangler 4 door driver
side rear door position.
Step 3b Attach the driver side RB Drop Step to the RB10 Running Board using
the U Brackets (3) 8MM SEMS Bolt, (FIGURE 4). Tighten all screws securing the
RB Drop Step, U Brackets and Auxiliary bracket to the R10 Running Board.
Repeat steps for the passenger side.
Typical RB Drop Step attachment to RB20 Running Board, driver side front or
rear door position
Step 1 Attach the Auxiliary Bracket to the U Bracket using ( 1) 8MM SEMS Bolt.
Do not tighten the screw, (FIGURE 1).
Typical RB Drop Step attachment to RB20 Running Board, driver side front or
rear door position.
Step 2 Determine the desired location of the driver side RB Drop Step on the
RB20 Running Board, then position (1) U Bracket toward the front of the
vehicle and the Auxiliary Bracket and U Bracket assembly toward the rear of
the vehicle in the opening on the underside of the RB20 Running Board, (FIGURE
2).
Typical RB Drop Step attachment to RB20 Running Board, driver side front or
rear door position. Step 3a Attach the driver side RB Drop Step to the RB20
Running Board using the U Brackets (3) 8MM SEMS Bolt, (FIGURE 3). Tighten all
screws securing the RB Drop Step, U Brackets and Auxiliary bracket to the R20
Running Board. Repeat steps for the passenger side.
Typical RB Drop Step attachment to RB20 Running Board, Jeep Wrangler 4 door
driver side rear door position.
Step 3b Attach the driver side RB Drop Step to the RB20 Running Board using
the U Brackets (3) 8MM SEMS Bolt, (FIGURE 4). Tighten all screws securing the
RB Drop Step and U Brackets to the R20 Running Board. Repeat steps for the
passenger side.
LIMITED WARRANTY
- Go Rhino warrants to Buyer that for a period of five (5) years from the date of shipment of the product(s) (“Warranty Period” Period”) for black finishes and chrome finishes, that such products will materially conform to the specifications set forth in Go Rhino’s specifications in effect as of the date of shipment(s) and will be free from material defects in material workmanship.
- Go Rhino warrants to Buyer that for the life of the product(s) from the date of shipment of the product(s) (“Warranty Period” Period”) for polished stainless steel finished products purchased after April 2004, that such products will materially conform to the spec ifi cations set forth in Go Rhino’s specifications in effect as of the date of shipments and will be free from material defects in material workmanship.
- Warranty claims must be accompanied with the original invoice and photos of the product. It is the customer’s responsibility to clean regularly and protect the finish with regular applications of a nonabrasive polish that is compatible with the product’s finish.
- This warranty covers the cost of the product only and does not include the cost of removal, installation, third-party modifications or shipping of the product. In no event shall Go Rhino be liable to buyer or any third party for any damage or harm caused by th e product or use thereof, regardless of weather such damages were foreseeable and whether or not Go Rhino has been advised of t he possibility of such damages, notwithstanding the failure of any agreed or other remedy of its essential purpose. This warran ty is void if the product shows signs of alteration, misuse, mishandling, improper care, neglect, improper application and/or damage due to improper installation.
- With respect to any such product(s) during the limited warranty period, Go Rhino shall, in its sole discretion, either: (i) provide aone time repair or replacement of such products (or the defective part) or (ii) credit or refund the price of such products at t he pro rata contract rate provided that, if Go Rhino so requests, Buyer shall, at Go Rhino’s expense, return such product(s) to Go R hin o. The remedies shall be the Buyer’s sole and exclusive remedy and Go Rhino’s entire liability for any breach of the limited warrant (ie s). Go Rhino disclaims all other warranties except to the extent that any such warranty cannot be validly disclaimed under applicable law.
Finish Limited Warranty:
- Limited lifetime on stainless steel products (after April 2004)
- 5 year warranty on black powder coat products
- 5 year warranty on chrome products
This warranty does not cover exposed welds
- Finish warranty covers peeling, flaking, or cracking. Washing all finishes regularly with car wash soap and rinsing well with wa ter is the best method for maintaining the finish on your products. You must also protect the finish with nonabrasive automotive wax on a regular basis. The use of any compound which contains abrasives becomes a self defeating exercise as the compound scratches the finish and opens it to corrosion. The use of harsh chemicals used to remove bugs and tar may also cause the finish to fail an d s hould be avoided.
- If you are unsatisfied with your purchase please contact the establishment you purchased the product from.
- If you need to place a warranty claim or need assistance, the Go Rhino customer service team will answer any questions you m ay have. Please contact the Go Rhino customer service team at 1 888 427 4466 during normal business hours Monday thru Friday 7 am to 5 pm PST. You may also email warranty@gorhino.com . In order to better serve you please provide a copy of the original invoice / receipt, a photo of the issue you are experiencing and a photo of the vehicle the product is installed on.
- All warranty returns must have an approved RGA number. The RGA number must be clearly marked on the exterior of the return package. All approved warranty returns must be shipped to Go Rhino Products, 1002 Carriers Drive, Laredo, Texas 78045.
PRODUCT REGISTRATION
Please remember to register your new purchase. You may register your product at www.gorhino.com . Registering your product may help speed any future warranty or customer service inquiries.
Thank you again for purchasing from Go Rhino Products Please take a few
minutes to view additional products for your vehicle and more at GORHINO.com
These installation instructions are available on the Go Rhino web site along
with installation videos for many of our products.
www.gorhino.com
www.bigcountryauto.com
www.gorhinopd.com
© 2016 Go Rhino Products. All rights reserved
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>