ENGO EONEBATW, EONEBATB Internet Controlled Thermostat User Guide

ENGO EONEBATW, EONEBATB Internet Controlled Thermostat

Product Specifications

• Product Name: Internet controlled thermostat, ZigBee
• Model: EONEBATW/B
• Software Version: ZigBee v1.0.12
• MCU Version: v2.0.3
• Manufacturer: Engo Controls S.C.
• Communication Standard: ZigBee 3.0
• Battery: Built-in Li-Ion 3.7V
• Functions: Control via ENGO Smart / Tuya Smart application, S1-S2 Input for additional sensor, Wireless communication via ZigBee 3.0

Product Usage Instructions

Safety Information:
Ensure compliance with national and EU regulations. Keep the device dry and for indoor use only. Read the entire manual before use.

Product Advantages:

• Built-in Li-Ion 3.7V Battery
• ZigBee 3.0 Standard Communication
• Control via ENGO Smart / Tuya Smart Application
• S1-S2 Input for additional sensor
• ENGO ENGO Binding Function

Connection Description:
Connect the thermostat to the ZigBee 3.0 network and the EGATEZB gateway using S1 and S2 inputs. Additional products like EMODZB Module and EREL1ZB12A Relay can be connected separately.

Technical Information:

• Power Supply: Li-Ion Battery
• Communication: ZigBee 3.0
• IP Protection Class : IP30
• Dimensions: 90 x 90 x 14 mm

User Interface Description:
Detailed description of the LCD icons and button functions for temperature settings, mode changes, and system operations.

Frequently Asked Questions (FAQ)

• What is the power source of the thermostat?
  The thermostat is powered by a built-in Li-Ion 3.7V battery.

• How do I connect the thermostat to the ZigBee network?
  To connect the thermostat to the ZigBee network, use the S1 and S2 inputs and ensure a gateway like EGATEZB is in place.

• Can I use the thermostat without the ENGO Smart app?
  No, thermostat programming is done through the ENGO Smart app, so it is essential for operation.

Product Compliance

This product complies with the following EU Directives: 2014/30/EU, 2014/35/EU, 2014/53/EU, 2011/65/EU

SAFETY INFORMATION

Use in accordance with national and EU regulations. Use the device only as intended, keeping it in a dry condition. The product is for indoor use only. Please read the entire manual, before installation or use.
WARNING:
This product must be used with a ZigBee EGATEZB gateway (purchased separately). Thermostat programming is done by ENGO Smart app.

Product advantages:

Wireless communication diagram

Connection description

Legend:

INTRODUCTION

EONEBAT is a surface-mounted room thermostat which works over ZigBee technology. It has a built-in humidity sensor and a minimum/maximum setpoint temperature limiting function. The EONEBAT has the ability to work in heating or cooling modes. The unique feature of this thermostat is the possibility of wireless control over ENGO binding function. In order to have the ability to controll wirelessly, EONEBAT needs to be used with ENGO Smart / TUYA Smart mobile application and EGATEZB internet gateway (sold separately). „ENGO binding” function provides wireless and direct connection to the receivers (e.g. ECB62ZB control box, EMODZB module or EREL1ZB12A relay) over the EGATEZB gateway. After adding to the mobile app, thermostat offer more functions, e.g. push notifications or possibility of programming time schedules.

Technical Informations

sensor
IP protection class| IP30
Dimension [mm]| 90 x 90 x 14 mm

LCD Icon Description + Button Description

1. Current humidity reading
2. Current/Setpoint temperature
3. Clock
4. Temperature unit
5. Heating indicator (icon is animating when there is heating demand)
6. Cooling indicator (icon is animating when there is cooling demand)
7. Schedule mode icon
8. Temporary override mode
9. External/Floor or Occupancy sensor
10. Button lock
11. Holiday mode
12. Settings icon
13. Battery indicator
14. Receiver binding indicator
15. ZigBee network connection indicator
16. Settings icon / temperature settings

Button description

Installation thermostat in the app

Make sure your router is within range of your smartphone. Make sure you are connected to the Internet. This will reduce the pairing time of the device.

• STEP 1 – DOWNLOAD ENGO SMART APP
  Download the ENGO Smart app from Google Play or Apple App Store and install it on your smartphone.

• STEP 2 – REGISTER THE NEW ACCOUNT
  To register a new account, please follow the steps below:

1. Click „Register” to create new account.
2. Enter your e-mail address to which the verification code will be sent.
3. Enter the verification code received in the email. Remember that you only have 60 seconds to enter the code!!
4. Then set the login password.

• STEP 3 – CONNECT THE THERMOSTAT TO ZigBee

  • Make sure ZigBee Gateway has been added to the Engo Smart app. Press and hold the buttons on the thermostat until the display shows „PA”. Then release the keys. The pairing mode will be started up.

  • Thermostat counts the time back (180s).

  1. Enter the gateway interface.

  2. In „Zigbee devices list” go „Add devices”.

  3. Wait for the message “End” to appear on the thermostat screen.

  4. After finding the device, go „Done”

  5. The thermostat has been installed and displays the main interface.

  6. On the controller screen globe icon appeared stating that he has been he added to the ZigBee network.

• Binding thermostat with the module/relay
  Make sure that the module/relay and thermostat are in the same ZigBee network (they are added to the same gateway EGATEZB).

1. To properly link thermostat with the module/relay first click quickly the button on the device 5 times. The LED diode will start flashing slowly on red, which means the device is in binding mode.
2. On the EONE thermostat, hold buttons until the “bind” message appears.

3. Release the keys, binding function process of linking thermostat with control box is active.
4. The “binding” process takes up to 300 seconds.

5. After successful binding operation „End” message will be displayed. LED on the module will stop flashing.
6. Both devices have been successfully linked. Thermostat displays the main screen, icon appeared on the screen indicating connection with the receiver (module/relay in this case).

ATTENTION:
If the binding process fails, it must be repeated taking into account the distances between devices, obstacles and local radio signal interferences.

• Binding thermostat with the ECB62ZB wireless control box
  Make sure that the ECB62ZB control box and thermostat are in the same ZigBee network (they are added to the same gateway EGATEZB) and the POWER LED lights up blue.

1. In order to correctly link thermostat with the control box, first select the zone in the control box with the SELECT button (1) (zone which you want to link with thermostat). The LED (2) will flash 3 times for the selected zone. Confirm your selection by clicking PAIR button (2). The LED (2) will flash green with the previously selected zone – binding process has started, it is active for 10 minutes and during this time you can link thermostat with the selected zone.

2. On the EONE thermostat, hold and buttons until the “bind”message appears.
3. Release the keys, binding function process of linking thermostat with control box is active.
4. The “binding” process takes up to 300 seconds.

5. After successful binding operation „End” message will be displayed.
6. Both devices have been successfully linked. Thermostat displays the main screen, icon appeared on the screen indicating connection with the receiver (ECB62ZB in this case).

ATTENTION:
If the binding process fails, it must be repeated taking into account the distances between devices, obstacles and local radio signal interferences.
Remember:
Radio range can be increased by Engo ZigBee repeaters.

Installer settings

• To enter installer parameters press and hold button for 3 seconds.

• Use . button to move between parameters. Enter the parameter by . Edit the parameter using . Confirm the new parameter value with the button.

Installer parameters

Factory reset

To RESET Thermostat to factory settings, hold down the buttons until the FA message appears. Then release the keys. Thermostat will restart, restore default factory settings and displays the home screen. The device will be removed from the ZigBee network you will need to add/pair it again.

ABOUT COMPANY

• Distributor:
  • QL CONTROLS Sp z o.o. Sp. k.
  • 43-262 Kobielice
  • 4 Rolna St.
  • Poland
• Producer:
  • Engo Controls S.C.
  • 43-262 Kobielice
  • 4 Rolna St.
  • Poland
• www.engocontrols.com

References

• ENGO Controls - Sterowanie ogrzewaniem

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>