ENGO CONTROLS EREL1ZB12A Smart Relay ZigBee User Guide
- May 15, 2024
- ENGO CONTROLS
Table of Contents
EREL1ZB12A
Smart Relay ZigBee, 12A
Quick Guide
Introduction
The product is designed for intelligent control devices that need to be controlled over voltage-free signal. The voltagefree output makes also possible to control devices which require 230V voltage. The size of the module allows to place it in a flushmounted installation box. It can be used as a boiler control relay for heating system („normally open” output logic). It works according to programmed schedules or scenarios (e.g. work dependent on the actions of others system elements, such as a window/door opening sensor or temperature controller). EREL1ZB12A can be controlled remotely (via smartphone and Engo Smart/Tuya app) or locally using a bistable/monostable switch.
The relay is equipped with the ENGO binding function, to connect it wirelessly witch selected thermostats (e.g. EONE) in Online or Offline modes.
WARNING:
This product must be used together with a EGATEZB ZigBee gateway (purchased
separately).
Product Compliance
This product complies with the following EU Directives:
2014/30/EU, 2014/35/EU, 2014/53/EU i 2011/65/EU.
Safety Information:
Use in accordance with national and EU regulations. Use the device only as
intended, keeping it in a dry condition.
The product is for indoor use only. Installation must be carried out by a
qualified person in accordance with national and EU regulations.
Installation:
Installation must be performed by a qualified person with appropriate
electrical qualifications, in accordance with the standards and regulations in
force in a given country and in the EU. The manufacturer is not responsible
for non-compliance with the instructions.
WARNING:
For the entire installation, there may be additional protection requirements,
which the installer is responsible for.
Input/Output EREL1ZB12A
- Power supply 230V AC
- Volt free output
- Volt free input
- Function button
- LED diode indicating the status of the module
LED diode indications
| EXPLANATION
---|---
LED diode flashes quickly on red
| The device is in pairing mode with the ZigBee network (when the device does
not has been previously added to the ZigBee network , or after restoring
factory settings)
LED diode flashes slowly on red
| The device is in binding mode (when the device has been previously added to
ZigBee network)
LED diode lights up green| Relay of the module has been turned ON
Button functions
| EXPLANATION
---|---
Press 1 time| Control of the modules relay (ON/OFF)
Press quickly 5 times| Enables binding process (to link EMODZB with
thermostat)
Press and hold approx. 8 seconds until the LED will starflashing red| Relay
reset (module will be removed from the ZigBee i network and automatically
will go into pairing mode)
Connection description
a) Connection diagram for gas boiler
b) Connection diagram for lighting
c) Connection diagram for pump / actuator
Legend:
| Boiler connection* -Boiler’s contacts for ON/OFF thermostat (according to
the boiler’s instructions)
---|---
L, N| 230V AC power supply
COM, NO| Voltage-free output
S1 in| 230V AC voltage output
| Pump
| Valve actuator
| Fuse
Installation thermostat in the app
Make sure your router is within range of your smartphone. Make sure you are connected to the Internet. This will reduce the pairing time of the device.
STEP 1 – DOWNLOAD ENGO SMART APP
Download the ENGO Smart app from Google Play or Apple App Store and install it
on your smartphone.
https://play.google.com/store
/apps/details?id=com.engo.smartlife|
| https://apps.apple.com/us/app/engo-
smart/id1606693444
---|---|---
STEP 2 – REGISTER THE NEW ACCOUNT
To register a new account, please follow the steps below:
Click „Register”
to create new account.| Enter your e-mail address to which
the verification code will be sent.
---|---
Enter the verification code
received in the email. Remember
that you only have 60 seconds to
enter the code!!| Then set the login
password.
STEP 3 – CONNECT THE RELAY TO ZigBee network
After installing the application and creating an account, follow these steps:
Make sure ZigBee gateway has been added to the Engo Smart app.| Make sure the
relay is connected to the power supply. The LED should flash quickly on red.
If not, hold down the button for about 8 seconds. The relay will enter pairing
mode.
---|---
Enter the gateway interface.| In „Zigbee devices list” go „Add devices”.
Wait until the application finds the device and click ”Done”.| The relay has
been installed and displays the main interface.
BINDING thermostat with the module/relay
Make sure that the relay and thermostat are in the same ZigBee network (they are added to the same gateway EGATEZB).
To properly bind thermostat with the relay first click quickly the button on the device 5 times. The LED diode will start flashing slowly on red, which means the device will enable binding mode.
On the EONE thermostat, hold and buttons until the „bind” message appears.
Release the keys, binding function (process of linking thermostat with control box) is active.
The „binding” process takes up to 300 seconds.
After successfull binding operation „End” message will be displayed. LED on the module will stop flashing.
Both devices have been successfully linked. Thermostat displays the main screen, icon ’’ ’’ appeared on the screen indicating connection with the receiver.
ATTENTION:
If the binding process fails, it must be repeated taking into account the
distances between devices, obstacles and local radio signal interferences.
Remember:
Radio range can be increased by Engo ZigBee repeaters.
Factory reset
To reset the device, press and hold the function button for approx. 8 seconds until the LED flashes red. The relay will be removed from the ZigBee network and gateway, then goes into pairing mode. Now it’s possible to add the relay again (see STEP 3 – CONNECT THE RELAY TO ZigBee network).
Ver. 5.1
Release date: II 2024
Soft: v1.0.9
Producer:
Engo Controls S.C.
43-262 Kobielice
Rolna 4 St.
Poland
Distributor:
QL CONTROLS Sp z o. o. Sp. k.
43-262 Kobielice
Rolna 4 St.
Poland
www.engocontrols.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>