ENGO CONTROLS EONEBATW Internet Controlled Thermostat User Guide
- October 30, 2023
- ENGO CONTROLS
Table of Contents
- Product Compliance
- SAFETY INFORMATION:
- Product advantages:
- INTRODUCTION:
- Technical Informations
- Wireless communication diagram
- Connection description
- LCD Icon Description + Button Description
- Button description
- Installation thermostat in the app
- Binding thermostat with the ECB62ZB wireless control box
- Installer settings
- Installer parameters
- Factory reset
- Documents / Resources
Internet controlled thermostat, ZigBee
Quick Guide
EONEBATW EONEBATB
Ver. 1
Release date: II 2023
Product Compliance
This product complies with the following EU Directives: 2014/30/EU, 2014/35/EU, 2014/53/ EU, 2011/65/EU
SAFETY INFORMATION:
Use in accordance with national and EU regulations. Use the device only as
intended, keeping it in a dry condition. The product is for indoor use only.
Please read the entire manual, before installation or use.
WARNING:
This product must be used with a ZigBee EGATEZB gateway (purchased
separately). Thermostat programming is done by ENGO Smart app.
Product advantages:
| Built-in Li-Ion 3,7V Battery
---|---
| Communication in the ZigBee 3.0 standard
| A multitude of functions available from ENGO Smart / Tuya Smart application
| S1-S2 Input for additional sensor
| ENGO binding function (devices connection in Online and Offline mode)
INTRODUCTION:
ONEBAT is a surface-mounted room thermostat which works over ZigBee technology. It has a built-in humidity sensor and a minimum/maximum setpoint temperature limiting function. The ONEBAT has the ability to work in heating or cooling modes. The unique feature of this thermostat is the possibility of wireless control over ENGO binding function. In order to have the ability to controll wirelessly, ONEBAT needs to be used with ENGO Smart / TUYA Smart mobile application and EGATEZB internet gateway (sold separately). „ENGO binding” function provides wireless and direct connection to the receivers (e.g. ECB62ZB control box, EMODZB module or EREL1ZB12A relay) over the EGATEZB gateway. After adding to the mobile app, thermostat offer more functions, e.g. push notifications or possibility of programming time schedules.
Technical Informations
| Power supply | Built-in Li-Ion 3,7V Battery |
|---|---|
| Charging connector | USB type C, 5V DC |
| Temperature range | 5,0°C – 45,0°C |
| Display temperature accuracy | 0,5°C |
| Control algorithm | TPI or Histeresis (from ±0,1°C to ±2°C) |
| Communication | ZigBee 3.0 2,4GHz |
| S1/S2 multifunctional input | Floor temp sensor, external air sensor, occupancy |
sensor
IP protection class| IP30
Dimension [mm]| 90 x 90 x 14 mm
Wireless communication diagram
Connection description
Products sold separately
Legend:
| Temperature sensor
---|---
S1, S2| Thermostat input for ext. temperature sensor
| Connection with ZigBee 3.0 network
| Connection with WiFi 2.4GHz network
LCD Icon Description + Button Description
1. Current humidity reading
2. Current/Setpoint temperature
3. Clock
4. Temperature unit
5. Heating indicator (icon is animating when there is heating demand)
6. Cooling indicator (icon is animating when
there is cooling demand)
7. Schedule mode icon
8. Temporary override mode| 9. External/Floor or Occupancy sensor
10. Button lock
11. Holiday mode
12. Settings icon
13. Battery indicator
14. Receiver pairing indicator
15. ZigBee network connection indicator
16. Settings icon / temperature settings
---|---
Button description
| Change the parameter value up
---|---
| Change the parameter value down
| Manual/Schedule mode – short button press (Online mode)
Enther the installer parameters- hold 3 seconds
Turn OFF/ON thermostat – hold 5 seconds
| Enter the pairing mode – hold 5 seconds
Enter binding mode – hold 10 seconds
Thermostat factory reset – hold 15 seconds
| Lock/Unlock thermostat keys – hold 3 seconds
| Heating/Cooling mode change – hold 3seconds
Installation thermostat in the app
Make sure your router is within range of your smartphone. Make sure you are
connected to the Internet.
This will reduce the pairing time of the device.
STEP 1 – DOWNLOAD ENGO SMART APP
Download the ENGO Smart app from Google Play or Apple App Store and install
it on your smartphone.
|
---|---
**<https://play.google.com/store/apps/details?id=com.engo.smartlife>**|
**<https://apps.apple.com/us/app/engo-smart/id1606693444>** STEP 2 – REGISTER THE NEW ACCOUNT
To register a new account, please follow the steps below:
Click „Register” to create new account.| Enter your e-mail address to which
the verification code will be sent.| Enter the verification code received in
the email.
Remember that you only have 60 seconds to enter the code!!| Then set the login
password.
STEP 3 – CONNECT THE THERMOSTAT TO ZigBee
Make sure ZigBee gateway has been added to the Engo Smart app.Press and hold the and buttons on the thermostat for approx. 5 seconds until the display shows „PA”. Then release the keys. The pairing mode will be started up and counts the time back (180s).
In the app, click on upper right corner.| Select: „Add Device”.| When the
ZigBee gateway finds thermostat click the „Add” button.
Name the device and click „Done”.| The thermostat has been installed and
displays the main interface.| On the controller screen globe icon appeared
stating that he has been he added to the ZigBee network.
Binding thermostat with the module/relay
Make sure that the module/relay and thermostat are in the same ZigBee network
(they are added to the same gateway EGATEZB).
To properly link thermostat with the module/relay first click the button on
the device 5 times.
The LED diode will start flashing slowly on red, which means the device is in
binding mode.
On the EONE thermostat, hold and buttons until the “bind” message appears.
Release the keys, binding function process of linking thermostat with control
box is active.
The “binding” process takes up to 300 seconds.
After successfull binding operation „End” message will be displayed. LED on
the module will stop flashing.
Both devices have been successfully linked. Thermostat displays the main
screen, icon ” ” appeared on the screen indicating connection with the
receiver (module/relay in this case).
ATTENTION:
If the binding process fails, it must be repeated taking into account the
distances between devices, obstacles and local radio signal interferences.
Remember:
Radio range can be increased by Engo ZigBee repeaters.
Binding thermostat with the ECB62ZB wireless control box
Make sure that the ECB62ZB control box and thermostat are in the same ZigBee
network (they are added tthe same gateway EGATEZB) and the POWER LED lights up
blue.
In order to correctly link
thermostat with the control box, first select the zone in the control box with
the SELECT button (1) (zone which you want to link with thermostat). The LED
(2) will flash 3 times for the selected zoneConfirm your selection by clicking
PAIR button (2). The LED (2) will flash green with the previously selected
zone – binding process has started, it is active for 10 minutes and during
this time you can link thermostat with the selected zone.
On the EONE thermostat, hold and buttons until the “bind”message appears.
Release the keys, binding functionprocess of linking thermostat with control
box is active.
The “binding” process takes up to 300 seconds.
After successfull binding operation „End” message will be displayed.
Both devices have been successfully linked. Thermostat displays the main
screen, icon ” ” appeared on the screen indicating connection with the
receiver (ECB62ZB in this case).
ATTENTION:
If the binding process fails, it must be repeated taking into account the
distances between devices, obstacles and local radio signal interferences.
Remember:
Radio range can be increased by Engo ZigBee repeaters.
Installer settings
To enter installer parameters press and hold button for 3 seconds.
Use or . button to move between parameters. Enter the parameter by . Edit the parameter using or . Confirm the new parameter value with the button .
Installer parameters
Pxx| Function| Value| Desription|
Default value
---|---|---|---|---
P01| Clock format| 12h| 12 hour| 24h
24h| 24 hour
P02| Heating/Cooling Selection| | Heating|
| Cooling
| | TPI UFH| TPI for Underfloor Heating|
TPI UFH for heating HIS 1.0 for cooling
| | TPI RAD| TPI for Radiators
| | TPI ELE| TPI for Electrical Heating
| | HIS 0.2| SPAN +/-0,1°C
| | HIS 0.4| SPAN +/-0,2°C
P03| Control algorithm| HIS 0.6| SPAN +/-0,3°C
| | HIS 0.8| SPAN +/-0,4°C
| | HIS 1.0| SPAN +/-0,5°C
| | HIS 2.0| SPAN +/-1,0°C
| | HIS 3.0| SPAN +/-1,5°C
| | HIS 4.0| SPAN +/-2,0°C
P04| Offset temperature| -3.5°C do +3.5°C| If the thermostat indicates wrong
temperature, you can correct it by max ± 3.5°C”| 0°C
P05| “Minimum setpoint”| 5°C – 45°C| Minimum heating / cooling temperature
that can be set| 5°C
P06| “Maximum setpoint”| 5°C – 45°C| Maximum heating / cooling temperature
that can be set| 35°C
P07| S1/S2 Input| 1| Disable|
1
2| External sensor as a floor sensor
3| External sensor as an air sensor
4| Occupnacy sensor (ON/OFF volt free input)
P08| Maximum floor temperature for heating (function active when P07=2)| 5°C –
45°C| In order to protect the floor, the heating will be turned off, when the
temperature of the floor sensor rises above the maximum value.| 35°C
P09| Minimum floor temperature for heating (function active when P07=2)| 5°C –
45°C| In order to protect the floor, the heating will be switched on, when the
temperature of the floor sensor drops below the minimum value.| 10°C
P10| Maximum floor temperature for cooling (function active when P07=2)| 5°C –
45°C| In order to protect the floor, cooling will be switched on, when the
temperature of the floor sensor exceeds the maximum value.| 15°C
P11| Minimum floor temperature for cooling (function active when P07=2)| 5°C –
45°C| In order to protect the floor, cooling will be turned off, when the
temperature of the floor sensor drops below the minimum value| 7°C
P12| Comfort warm floor| OFF| This function helps to keep the floor warm, even
if there is no heating demand from the room thermostat.This feature is
available only for Heating Mode. User can select 5 levels of warm floor
feature. Note that comfort warm floor function will activate heating for
specified amount of time (in relation to Level setting choosen by user).
Heating will be activated only if in the past 1 hour heating was OFF.|
OFF
Level 1 = 7min
Level 2 = 11min
Level 3 = 15min
Level 4 = 19min
Level 5 = 23min
P13| Valve protection| ON| Function disabled| OFF
OFF| Function enabled
P14| Backlight brightness| 10% – 100%| Adjustable in the range from 10 to
100%| 50%
P15| PIN Code for settings access| NO| Function disabled| NO
PIN| Function enabled
P16| Require a PIN to unlock the keys every time (function active when
P15=PIN)| NO| Function disabled| NO
YES| Function enabled
CLR| Clear settings factory reset| NO| No action| NO
YES| Factory Reset
Factory reset
To RESET thermostat to factory settings, hold the and buttons for approx. 15 seconds. FA will be displayed. Then release the keys. Thermostat will restart, restore default (factory) settings and displays the home screen. The device will be removed from the ZigBee network you will need to add/pair it again.
Producer:
Engo Controls S.C.
43-200 Pszczyna 3E Górnośląska St.
Poland Distributor:
QL CONTROLS Sp z o.o. Sp. k.
43-262 Kobielice 4 Rolna St. Poland
www.engocontrols.com
Documents / Resources
| ENGO
CONTROLS EONEBATW Internet Controlled
Thermostat
[pdf] User Guide
EONEBATW, EONEBATB, EONEBATW Internet Controlled Thermostat, Internet
Controlled Thermostat, Thermostat
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>