SmallRig 4297 Wireless Receiver Motor Instruction Manual

SmallRig 4297 Wireless Receiver Motor

Operating Instruction

• PMN: Wireless Receiver Motor

• HVIN: 4297

• Thank you for purchasing SmallRig’s product.

• Please read this Operation Guide carefully.

• Please follow the safety warnings.

Kits and Accessories

1. Wireless Handwheel Controller
2. Snap-on Follow Focus Gear Ring
3. Wireless Receiver Motor
4. Rod Clamp with NATO Rail
5. Allen Wrench
6. ∅M16mm Dod I
7. USB-C to USB-C Cable

Instructions for Product Functions

Instructions for Product Installation and Power Supply Control

1. Instructions for Installation of Wireless Receiver Motor
2. Instructions for Power Supply to Wireless Receiver Motor.
3. The wireless receiver motor is powered by the included USB-C cable.
4. The wireless receiver motor is compatible with PD + QC protocols, providing high torque output; and the input voltage ranges from 5 V to 18 V. Instructions for Wireless
5. Handwheel Controller. The input voltage of wireless handwheel controller ranges from 5 V to 12 V; an external power adapter supplies power to the wireless handwheel controller via the included USB-C cable.

Instructions for Product Operation Steps

Ensure that the indicator of the wireless receiver motor is consistent with that of the wireless handwheel controller to guarantee the control; Double- click the button to cycle through the frequency bands, F00-01 F15-01. [Note] The light color information corresponds to the frequency bands of the MagicFIZ wireless receiver motor and wireless handwheel controller. Automatic Lens Travel Calibration
Long press the CAL button for 2 seconds to start automatic lens travel calibration.

Manual Lens Travel Calibration

Long press the CAL button for 2 seconds to start automatic lens travel calibration; single-click the CAL button to switch to manual travel calibration.

Point A / B Marking Operation

Single-click the A / B mark (A-B-cancel) to mark the point.

1. Operation to Address Abnormality of Wireless Handwheel Controller
2. The red light flashing indicates the alarm of low battery level or wireless receiver motor.

Description of Abnormal Alarm Case for Wireless Receiver Motor.

1. The lens damping is too high, and the motor is stuck by a foreign object.
2. The motor input voltage is too low.

Operation to Address Abnormality of Wireless Receiver Motor.

1. Increase the input voltage or connect a device that supports PD+QC for power supply;
2. Use the included USB-C power cable or a USB3.0 power cable;
3. Single-click the CAL button on the wireless receiver motor or any button on the wireless handwheel controller to recalibrate the lens travel.

Operation to Address Abnormal Forward / Reverse Rotation of Wireless Receiver Motor.

1. The wireless receiver motor shows abnormal reverse rotation
2. 1. Turn to the end position as shown in the Figure.
3. Long press the button for 5 seconds until the current status light stops flashing to complete the reset operation.

FCC Warnning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

ISED Statement

This device contains licence-exempt transmitters)/receivers) that comply with Innovation, Science and Economic Development Canada’ s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator & vour body.

Manufacturer: Shenzhen Leqi Innovation Co., Ltd.
Add: Rooms 103, 501 and 601, Building 5, Fenghe Industrial Park, Nos. 1301-50 Guanguang Road, Longhua District, Shenzhen, Guangdong, China.
Add: Rooms 602, Building 5, Fenghe Industrial Park, No. 1301-50 Guanguang Road, Xinlan Community, Guanlan Street, Longhua District, Shenzhen, Guangdong, China.

Tutorial of Wireless Follow Focus

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>