EWF36A Wood Burning Fireplace

Product Information

Specifications

• Model: Vermont Castings SEQUOIA EWF36A
• Type: Solid fuel, woodburning, heat circulating fireplace
• Manufacturer: Appliance Factory Parts
• Warranty: Refer to manual for warranty details

Product Usage Instructions

Safety Information

Before installing and using the fireplace, it is crucial to read
the manual thoroughly to ensure safe operation. Failure to follow
instructions may result in fire hazards and void the warranty.

Precautions

• Ensure all components are undamaged before installation.

• Only use MHSC components to avoid voiding the warranty and
  creating fire hazards.

• Consult with a certified installer for proper
  installation.

• Check local building codes for compliance before
  installation.

• Vent the fireplace and chimney system outdoors.

• Do not obstruct air inlets/outlets or modify the fireplace
  surround with combustible materials.

• Burn only solid wood fuel.

• Operate the EWF36A with doors closed or fully open, with the
  optional spark screen in place.

• Do not install any products not specified for use with this
  fireplace.

• This fireplace is not approved for installation in mobile
  homes.

FAQ

Q: Can I install the EWF36A fireplace in a mobile home?

A: No, the EWF36A fireplace is not approved for installation in
mobile homes. Please refer to local building codes for suitable
installation locations.

Q: What type of fuel should I burn in the EWF36A

fireplace?

A: The EWF36A fireplace is designed for use with solid wood fuel
only. Do not burn any other materials in the fireplace to avoid
hazards.

Q: Do I need to keep the doors closed when operating the EWF36A

fireplace?

A: The EWF36A fireplace should be operated with the doors closed
or fully open, with the optional spark screen in place. Follow
these guidelines for safe operation.

This Owner’s Manual is provided and hosted by Appliance Factory Parts.
Vermont Castings SEQUOIA EWF36A
Owner’s Manual
Shop genuine replacement parts for Vermont Castings SEQUOIA EWF36A
Find Your Vermont Castings Fireplace Parts – Select From 28 Models ——– Manual continues below ——–

EWF36A Fireplace
Homeowner’s Installation and Operating Manual
SAFETy NoTicE: iF ThiS AppliANcE iS NoT pRopERly iNSTAllED, opERATED AND MAiNTAiNED, A hoUSE FiRE MAy RESUlT. To REDUcE ThE RiSk oF FiRE, FolloW ThE iNSTAllATioN iNSTRUcTioNS. FAilURE To FolloW iNSTRUcTioNS MAy RESUlT iN pRopERTy DAMAgE, boDily iNjURy oR EvEN DEATh. coNTAcT locAl bUilDiNg oFFiciAlS AboUT RESTRicTioNS AND iNSTAllATioN iNSpEcTioN REqUiREMENTS iN yoUR AREA.
Do Not Discard This Manual: Retain for Future Use
20005167 12/10 Rev. 16

Vermont Castings EWF36A
introduction
Thank you for purchasing a Vermont Castings, EWF36A fireplace. An efficient fireplace carefully engineered to bring you the latest in wood combustion principles and modern foundry technology. You can count on years of comfortable heating and pleasurable fire viewing if you treat it properly and operate the EWF36A according to the directions in this owner’s guide. The EWF36A is listed by Underwriter’s Laboratories, and is in compliance with the standards set forth by the Federal Environmental Protection Agency, 40 CFR Part 60.532(b), as stated on the permanent label attached to each appliance. This manual describes the installation and operation of the EWF36A wood heater. This heater meets the US Environmental Protection Agency’s emission limits for wood heaters sold after July 1, 1990. Under specific test conditions this heater has been shown to deliver heat at a rate ranging from 11,000 to 68,600 Btu’s/hr. For more complete details on the EWF36A performance and specifications, please refer to Page 3. The EWF36A is designed, tested and listed for burning wood. Do not burn other fuels. Installation or service of this woodburning firep should only be completed by a qualified installer, preferably NFI or WETT (Canada) certified. Please read the appropriate sections of this manual before you install and use your EWF36A. For information on operation and maintenance of the EWF36A, refer to Pages 17 and 20. The EWF fireplace can use 100% outside air with the AKMST Outside Air Kits installed. Failure to follow these instructions may result in property damage, bodily injury or even death. Save These instructions for Future Reference

Table of contents
Introduction………………………………………………………. 2 Safety Information …………………………………………….. 3 Specifications …………………………………………………… 4 Planning Information………………………………………….. 7 Installation ……………………………………………………….. 8 Operation……………………………………………………….. 18 Maintenance …………………………………………………… 22 Replacement Parts ………………………………………….. 27 Optional Accessories ……………………………………….. 29 Warranty ………………………………………………………… 31

proposition 65 Warning: Fuels used in gas, woodburning or oil fired appliances, and the products of combustion of such fuels, contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. California Health & Safety Code Sec. 25249.6

2

20005167

Vermont Castings EWF36A

Safety information
please Read This Manual before installing and Using Fireplace
iMpoRTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty.

Description
The EWF36A fireplace is a solid fuel, woodburning, heat circulating fireplace.
precautions
MHSC fireplaces and component parts have been highly tested and will operate safely when installed in accordance with instructions provided in this manual. Carefully read and understand all instructions before beginning installation.
If you notice any damage to fireplace or component parts, immediately report damage to your MHSC dealer.
Only use MHSC components or the warranty will be voided and a fire hazard may be created.
MHSC warranty will be voided by and MHSC disclaims any responsibility for the following actions:
· installation by any other than a qualified
installer, preferably NFi or WETT (canada) certified.
· installation of any damaged fireplace or chim-
ney component;
· Modification of fireplace, chimney assembly
or any component parts thereof; (except for chase flashings as detailed in MHSC Chimney Top installation instructions).
· installation other than as instructed by MhSc;
or
· installation and/or use of any component part
not manufactured or approved by MhSc in combination or assembly with a MhSc fireplace system, notwithstanding any independent testing laboratory or other third party approval of such component parts or accessory.
Any such action may possibly cause a fire hazard.
Consult local building codes to ensure that you are in compliance before installing the fireplace.
This fireplace and chimney system must be vented to the out-of-doors.

Do not obstruct or modify air inlets/outlets in any manner. Do not install combustible materials on any of the black fireplace surround. burn only solid wood fuel. The EWF36A is intended for operation with the doors closed or fully open only with the optional spark screen in place. Do not install a solid fuel burning insert or other products not specified for use with this fireplace. This fireplace is not approved for installation in mobile homes.
NoTE: hairline cracks in hearth brick and ash lips are not a safety issue and do not need to be replaced.
Drafts
The fireplace should not be located in areas that create drafts (ie: frequently opened doors and central heating air inlets/outlets) that hamper the normal flow of air into the fire.
EWF36A listed
Ul / Ulc127 Standard for Factory built Fireplaces

20005167

3

Vermont Castings EWF36A

Specifications

EWF36A

Range of heat output*……………. 11,300 – 75,500 Btu/hr Maximum heat output ….. in excess of 100,000 Btu/hr EPA emissions rating (g/h, catalytic) …………………..2.4 Area heated…………… Up to 2500 sq. ft. (558 sq. m) Size of wood splits…………………18″ – 24″ (450-610mm) Fuel Capacity…………………………………….. 40lbs. (18kg) Loading …………………………………………………………Front Flue size …………………………………………….. 8″ (200mm) Fireplace weight ………………………………………… 741lbs. Primary Air Control …………………………………….. Manual Glass panel…………………….. High-temperature ceramic Flue exit position……………………………………………… Top Blower rating…………………………..160cfm. (115V, 60Hz)

Under specific test conditions used during EPA emissions standard testing.
This value can vary depending on how the unit is operated, and the type and moisture content of the fuel used. Figure shown is based on maximum fuel consumption obtained under laboratory conditions and on average efficiencies.
These values are based on operation in buildingcode conforming homes under typical winter climate conditions. If your home is of nonstandard construction (e.g. unusually well insulated, not insulated, built under ground, etc.) or if you live in a more severe or more temperate climate, these figures may not apply. Since so many variables affect performance, consult your Vermont Castings’ Authorized Dealer to determine realistic expectations for your home.

EWF36A Woodburning Fireplace

6756M” (1708mm)
” (25mm)

”

Rough Opening Depth

27″

856O”

(686mm) (216mm)

26″ (660mm)

41″ (1041mm)

Rough Opening Height

Rough Opening Width 43″ (1092mm)

1356O” Dia. (343mm)
6 ” Recessed (16mm) Nailing
Flange

6756M” (1708mm) 95″ (2413 5m/8m”)4(7516O6″m(1m)207mm)

12(6 ” (327mm)
1456M” (362mm)

4756O” (1207mm)
5156O” (1308mm)

Fig. 1 EWF36A specifications and framing.

Outside Air

12(6 ” (327mm)

36″ (914mm) 41″ (1041mm)

Electrical Access

1256O” (318mm)

1456M” (362mm)

4(6 ”

(124mm)

4

20005167

chase installation Insulation methods shown are optional for cold climate, not a requirement for unit operation.
Batt Insulation (cut out around firestop) Firestop Ceiling Level
Batt Insulation MUST be used in the Chase.
Outside Air Cover Plate
Fig. 2 Fireplace and chase parts identification.

Vermont Castings EWF36A
Termination Cap Storm Collar Pan Flashing
Draftstop

Standoff Brick Ledge

Andiron
Metal Safety Strips (1,2 or 3 pieces)

FP554a

20005167

5

Vermont Castings EWF36A
chimney Requirements – offset installations
CHIMNEY FLUE EXIT

Offset

A B

Chimney Section

Elbow

B

G

30° Return Elbow

D E Rise
6 FT. C
H Offset

30° Offset Elbow 30° Return Elbow

G
TCS8A Support

H

30° Offset Elbow

Hearth Floor

Example 1

Example 2

Example 3

Notes: G + H cannot exceed 20 feet.

FP269

Air Space Clearances: “S” Series (3-wall) = 2″ Min. to Combustibles

illustration key

The following safety rules apply to offset installations (letters correspond with illustration above):
A. Height of the chimney is measured from the hearth to the chimney exit.

Maximum: Minimum:
Without Elbows With 2 Elbows With 4 Elbows

EWF36A 50′
17’0″ 19’0″ 21’0″

b. Do not use more than 4 elbows per chimney.
Attach the straps of the return (top) elbow to a structural framing member.
The offset (first) elbow of any pair does not have straps.

c. The chimney cannot be more than 30 (45 in Canada) from the vertical plane in any installation*.
D. The maximum length of the angled run of the total chimney system is 20 feet. (G plus H cannot exceed 20 feet.)
E. A chimney support (Model TCS8A) is required every 6 feet of angled run of chimney. Chimney supports are required for every 30 feet and 60 feet of vertical chimney height above the hearth.
Determine the offset distance of your chimney arrangement from the centerline of the fireplace to the centerline of the chimney where it is to pass through the first ceiling.
NoTE: This offset distance may not be your full offset distance. See Examples 2 and 3.

Fig. 3 Chimney system requirements. 6

Rise

FP282
30 Elbow offsets

chimney Support

1′ 1¹/’ 3′ 4′

offset Rise

0000 0

3″

11″

1 0 0 0 0 8¹/” 20″

0 1 0 0 0 11¹/” 25¹/”

2 0 0 0 0 13¹/” 29¹/”

1 1 0 0 0 16¹/” 34¹/”

0 0 1 0 0 20¹/” 40³/”

2 1 0 0 0 21³/” 43¹/”

0 0 0 1 0 26¹/” 51¹/”

0 1 1 0 0 28¹/” 55¹/”

1 0 0 1 0 31¹/” 60¹/”

0 1 0 1 0 34¹/” 65¹/”

0 0 2 0 0 37¹/” 70³/”

1 1 0 1 1 41¹/” 77³/”

0 0 1 1 1 45″ 83³/”

0 1 2 0 1 47¹/” 87¹/”

0 0 0 2 1 51″ 94″

0 1 1 1 1 53¹/” 98″

0 0 3 0 1 56¹/” 103¹/”

0 1 0 2 1 59¹/” 108¹/”

0 0 2 1 1 62¹/” 113¹/”

0 1 3 0 1 64¹/” 117¹/”

0 0 1 2 1 68¹/” 124″

0 1 2 1 1 70¹/” 128″

0 0 0 3 1 74¹/” 134¹/”

0 1 1 2 2 78″ 140³/”

0 0 3 1 2 81″ 146″

0 1 0 3 2 84″ 151¹/”

0 0 2 2 2 87″ 156¹/”

0 1 3 1 2 89¹/” 160¹/”

0 0 1 3 2 93″ 166³/”

0 1 2 2 2 95¹/” 170³/”

0 0 0 4 2 99¹/” 177³/”

0 1 1 3 2 101¹/” 181³/”

0 0 3 2 2 104¹/” 186¹/”

0 1 0 4 2 107¹/” 191¹/”

0 0 2 3 2 110¹/” 196³/”

0 1 3 2 3 114″ 203¹/”

0 0 1 4 3 117³/” 209³/”

0 1 2 3 3 120″ 213¹/”

0 0 0 5 3 123³/” 220″

20005167

Vermont Castings EWF36A

planning information

Planning an installation is very important to ensure safety and to save time and money. An installer must predetermine where a fireplace will be set and how the chimney system will be run.
NoTE: If installing the EWF36CFTK at a later date and if the hearth is being raised in front of the firepalce, the fireplace must be raised to the same height.
Mounting the Fireplace
The fireplace is shipped with lifting handles attached to each side with lifting straps. NoTE: The lifting straps are intended for ligting unit off of the skid and final positioning. Unit should remain on skid until final positioning. After fireplace is in position, the lifting handle and straps may be removed or left in place.
A fireplace may only be mounted on the following surfaces:
1. A flat combustible surface. 2. A raised wooden platform. 3. A concrete block or other solid object placed beneath
each of the four (4) corners of the fireplace.
The fireplace must be spaced 1″ from a combustible back wall and 1″ from a combustible side wall or support. (Page 13, Fig. 17)
planning the chimney Run

LT

TRIPLE

TOTAL INSTALLED LENGTH LENGTH

WALL

(LT)

(L1)

L1 81 818
83 L1 84

56O”
56O” 56O” 56O”

56O”
56O” 56O” 56O”

FP288a

Fig. 4 Installed lengths of chimney sections.
Determine how the chimney will be run, length of run and chimney components required to complete the job. (Fig. 4) Never install a chimney below minimum heights.
In planning a chimney system, it is important to know: 1. The height of a chimney is measured from the hearth
to the exit point on the termination.
2. A chimney cannot be offset more than 30° from a vertical plane.
3. A chimney may run straight up or it may be necessary to offset it to avoid obstructions.
4. The maximum length of an angled run (total chimney system) is 20 feet.

5. No more than 2 offsets (4 total 30° elbows in U.S./or 2 total 45° elbows in Canada) per fireplace may be used.
6. A guy wire stabilizer is required for chimneys extending more than 6′ (1.8m) above a roof line.
The Ten Foot Rule
Major U.S. building codes specify a minimum chimney height above the roof top. The “Ten Foot Rule” is a fire safety rule and not a draft rule. To ensure proper draft, it is recommended that you always meet or exceed the “Ten Foot Rule,” especially when installing a termination on a high pitch roof. (Fig. 5)
The key points of the “Ten Foot Rule” are:
1. If the horizontal distance from the chimney to the peak of the roof is 10′ (3m) or less, the top of the chimney must be at least 2′ (610mm) above the peak of the roof, but never less than 3′ (914mm) in height above the highest point where it passes through the roof.
2. If a horizontal distance from the chimney to the peak of the roof is more than 10′ (3m), a chimney height reference point is established that is on the surface of the roof a distance of 10′ (3m) from the chimney in a horizontal plane. The top of the chimney must be at least 2′ (610mm) above the reference point, but never less than 3′ (914mm) in height above the highest point where it passes through the roof.

0 To 10′

2′ Min. 3′
Min.
Reference Point

0 To 10′
2′ Min. 3′ Min.

Fig. 5 Ten Foot Rule illustration.

AC246

20005167

7

Vermont Castings EWF36A
chimney Supports
The chimney system is supported by the fireplace for vertical chimney heights less than 30′ (9m) above the hearth. Chimney supports are required if the vertical height exceeds 30′ (9m). Locate chimney supports at ceiling holes or other structural framing at 30′ (9m) heights. Spacing between chimney supports must not exceed 30′ (9m). Use Chimney Support Model TCS8A. (NoTE: The TcS8A cannot be mounted directly to the fireplace.) Support provided by elbow straps fulfills the support requirement only if they are spaced as previously described. (A chimney support is 2¹/” (64mm) long when installed.)
Angled chimney runs require a support every 6′ (1.8m) in addition to the elbow straps. Chimney supports are
used for this function. (Fig. 6)

Chimney Support Strap

TCS8A

FP284a

Fig. 6 Chimney support installation.
chase installation
A chase is a vertical box-like structure which encloses the fireplace and/or chimney. Chases are typically built on the outside of the house with fireplace opening cut into the outer wall of a room. (Page 5, Fig. 2)
If you need help in determining fireplace location or how the chimney system should be run, contact your Vermont Castings dealer for assistance.

installation
insulating Fireplace Enclosure for cold climates
If you live in a cold climate, it is not required but highly recommended that you insulate fireplace enclosure to eliminate cold air penetration as much as possible. Insulate base of fireplace with a noncombustible insulation rated for a minimum of 300° F. Insulating is very important for outside wall installations over a concrete slab. If fireplace is installed on a platform, insulation should be placed on top of the platform before fireplace is set. (Fig. 7) When a fireplace is installed in a chase or on an outside wall, enclosure should be treated like any outside wall in a home. Insulation should be installed on the inside wall as well as the outside wall(s). In a chase, it is also a good idea to install a firestop at the first ceiling level above the fireplace and enclose the chase with sheeting material. Insulation may then be installed above sheeting material to assure the space around the fireplace is totally protected. (Fig. 2) When installing the chimney, Do NoT caulk between outer pipe and firestop. It is vital that some air be allowed to flow through this very thin gap. cAUTioN: When installing a fireplace in an insulated enclosure, be sure all required air spaces are maintained. (page 13, Fig. 17)
Hard Flat Surface

Insulation

Platform Fig. 7 Insulating between platform and fireplace.

FPC555a

8

20005167

Framing
Framing can be constructed before or after the fireplace is set in place, however, most installers build the frame before setting the fireplace.
Frame fireplace with 2 x 4 lumber or heavier materials. Refer to framing dimensions in Figure 1 for basic fireplace specifications.
NoTE: Framing should be positioned to accommodate wall covering and fireplace facing material.
Eb1 (Receptacle) hookup
option for circulating Models only
Wiring should be installed by a certified electrician.
Turn off circuit breaker before wiring models.
Once fireplace is secured, complete wiring the fan kit. Remove knockout in the center of the back of the EB1 and install listed cable clamps. Feed electrical wire through listed cable clamp leaving approximately six (6) inches of wire exposed through the EB1. Secure listed cable clamp to the wire.
Attach white wire from power source to one (1) wire of receptacle and secure with nut. Attach black wire from power source to the other wire of receptacle and secure with nut. Be sure nuts are secured tightly.
Secure EB1 assembly to inside of electrical box coverplate using two screws. Attach cover to face of the EB1 while being careful to position excess wire completely within the EB1, then attach coverplate to fireplace.
chimney Set-Up
Since you have already planned the chimney run, you should know exactly how the installation is to be accomplished – how much pipe is required, the number of elbows, if any, and type of termination to be used.
cAUTioN: Report to your dealer any parts damaged in shipment, specifically check the end connection of chimney sections and elbows.
NoTE: The EWF36A fireplace must use MHSC model triple wall 8″ chimney components only. The installation procedure described in this manual applies only to this system.
Straight-Up chimney installation
To mark the centerline of the flue, put the fireplace in final position and measure out from the wall: 9¹/” (241mm). Mark a spot on the ceiling directly above the fireplace. Draw a line parallel to the back wall through this mark. (Fig. 8)
Using a plumb bob positioned directly over center point of fireplace flue collar, mark the ceiling to establish the chimney center point. (Fig. 8)
20005167

Vermont Castings EWF36A

Chimney Centerline Actual Centerpoint

956O” (241mm)

Plumb Line
Plumb Bob Imaginary Centerpoint

FPC556a
Fig. 8 Locate centerline of chimney with plumb line.
offset installation
In order to clear an obstruction, it may be necessary to offset chimney from vertical. This is accomplished by using elbows. Use the 30 Offset Elbow table on Page 6 to determine proper offset and parts required.
Each offset requires two (2) elbows. The second elbow is equipped with support straps. It is very important to install the second elbow in each offset as close to the ceiling or support as possible so that the elbow straps can be secured to framing members to help support the weight of the chimney.
Determine offset distance of your chimney arrangement from centerline of fireplace to centerline of chimney where it is to pass through ceiling.
Locate center point of the chimney on ceiling as though a straight up chimney arrangement is to be used. Measure your offset dimension from straight up chimney center point on ceiling.
9

Vermont Castings EWF36A

ceiling chimney hole/ possible obstructions

The size of the hole in ceiling will vary with the angle at which the chimney passes through ceiling.
Drive a nail up through ceiling at marked chimney center point. Go to floor above and see where hole will be cut. Check to see where existing ceiling joists and other possible obstructions are located…i.e. wiring, plumbing etc… If necessary, re-position chimney and/or
fireplace to avoid obstructions.

cutting the hole

Cover fireplace collar opening and cut proper sized chimney hole in chimney.

Framing the ceiling hole

Frame the ceiling chimney hole as shown in Figure 10. It is good practice to use framing lumber that is the same size as the ceiling joists; this is a requirement at attic level.
The following table gives firestop spacer model numbers:
chimney hole Size

Angle of Chimney at Ceiling

Size of Chimney

Vertical

30°

FS2A

FS6A

8″ Flue

17¹/” x 17¹/” 17/” x 29/”

(445 x 445mm) (454 x 753mm)

Fig. 9 Ceiling chimney hole sizes necessary for installing firestop spacer.

The inside dimension of the frame must be the same as the hole size selected from Figure 9 in order to provide required the 2″ (51mm) air space between the outside diameter of the chimney and the edges of the
framed ceiling hole.

positioning, Safety Strips, Securing the Fireplace

Slide fireplace into position.
Safety strips are used to ensure that any combustible materials in front of the fireplace are protected even though a noncombustible hearth extension is required.
When the finished extended hearth is added, the top of the finished hearth must be flush with the bottom of the fireplace. “Z” shaped metal safety strips have been supplied with the fireplace and are required for installation. The safety strips provided have a 1″ offset. For applications with a greater offset, “Z” shaped strips will have to be fabricated of metal. Overlap safety strips at least 1/2″ to provide a positive joint. The safety strips must also extend at least 1¹/” (38mm) beyond the sides of the fireplace. (Fig. 11)

10

Existing Ceiling Joists

17¹/” (445mm)

17¹/” (445mm)
Chimney Hole

New Framing Members

Ceiling

Fig. 10 Typical frame for ceiling chimney hole.

FP551b

“Z” Metal Safety Strips (1 or 2 pcs.)

1¹/” (38mm)

1/2″ Min. Overlap

Fireplace Platform

“Z” Safety Strip
Decorative Hearth Face

Hearth Ext.

FP557b

Fig. 11 Safety strip installation.

NoTE: Safety strips are not required over noncombustible floors where all supports at the base of the fireplace are noncombustible.

Two (2) nailing flanges are supplied with the fireplace. To level the box and secure it firmly in place, remove the nailing flanges from the hearth and install at the sides of the fireplace as shown in Figure 12.

20005167

Nail Top Standoffs
Nail Side Nailing Flanges
FP1197
Fig. 12 Fasten fireplace in position.
installating outside Air kit
An outside air kit may be installed on the EWF36A. If desired, or if local codes mandate the use of an air kit, then two (2) AK-MSTs are required to complete the installation (from air kit to the outdoors). If the outside air kits are to be used, the AK-MSTs MUST be installed BEFORE the fireplace is enclosed. NoTE: Air duct assemblies must be installed in conjunction with the AK-MST or cold air will enter the home. (Fig. 14) NoTE: Four (4) inch Class 1 air duct, material or metal duct (not supplied) may be used with AK-MST. (For installation in New york State, only aluminum, noncombustible flexible or type “o” metal ducting is permissible.)
installation precautions
The duct termination should be located so it is exposed to an out-of-doors opening at least 100 square inches. If the duct termination must be located in a crawl space or basement, be sure the termination area has 100 square inches of ventilation opening to outside air. The duct termination must be located so it does not compete for air flow with exhaust fans, gas vent hoods or other air consuming devices or appliances. It must not be obstructed by rafters, insulation materials or other obstructions. The less restrictive the air supply, the better the AK-MST will perform. It is a good practice to protect your hands and eyes during installation by wearing work gloves and safety glasses. cAUTioN: Do not install termination into a garage or other area that could contain flammable liquids or fumes, or into an attic space.
20005167

Vermont Castings EWF36A
installation instructions
Determine the location of the fireplace as described in the fireplace Installation Manual. Then plan location of the duct termination and the route of the duct run between the fireplace and the duct termination.
Duct run must be limited to a maximum distance of 40 feet from the fireplace pipe collar to duct termination. This will provide the least restriction to air flow. No more than four (4) 90° elbows can be used. Duct run may be horizontal, vertical, inclined or any combination of these. Vertical duct runs must be at least three (3) feet below the fireplace chimney flue exit. (Fig. 13) You are now ready to install the AK-MST Outside Air Kit.

Duct Termination

Must be More Than 3′

Below Chimney

Attic

Duct Termination 40′ Max. Duct Run

Ceiling Duct

Soffit Termination

Exterior Wall Rain Cap

40′ Max. Duct Run

Duct Termination

Duct

Exterior Wall Termination

FP1060

Fig. 13 Typical installations.
1. Remove and discard the outside air cover plate located at the center of both sides of the fireplace. Use care not to rub against the sharp edges of this opening to avoid cuts. Remove the four (4) screws

11

Vermont Castings EWF36A
exposed when cover plate is removed. Retain for future use. 2. Slide the two (2) air duct assemblies provided with the unit into the openings on each side of the unit. (Fig. 14) 3. Attach the air duct assemblies to the inside panel with four (4) screws removed in Step 1. (fig. 14)
Air Duct Assembly

AK-MST
FP1654
Fig. 14 Air duct assembly.
4. Attach the inlet collar with four (4) #10 screws to the side near the bottom of the fireplace. Slide the duct over the collar and attach the duct to the collar using the plastic tie straps or three (3) screws (screws not
provided). Continue attaching the ducting together
using three (3) screws at each joint until you have installed sufficient duct to arrive at your duct termination location.
5. At the termination end, install the duct termination. This should be installed from the outside of the home. Cut a hole in the desired location approximately 4¹/” in (114 mm) diameter, caulk around the hole, and slide the termination through the opening from outside the home. The termination/rain cap should be caulked around its perimeter to assure a tight seal. The rain cap opening should be positioned downward. (Fig. 15)
The AK-MST Outside Air Kit is now installed and ready for use.

Caulking

Duct Termination

Rain Cap

Wall

FP1061

Fig. 15 Caulk and install duct termination/rain cap in place.

12

installing the chimney System
Start by attaching the first chimney section to the collar on top of the fireplace.
Install the pipe as pictured in Figure 16. When you get a good lock, you will hear the pipe clearly snap together. Once sections are snap-locked in place, it is extremely difficult to get them apart. Make sure the pipe is firmly snapped and locked together as each pipe section is mounted.
When installing elbows, only outer pipe will snap- lock. Middle pipes simply slide into position. Be sure to always attach straps on upper elbow to a structural framing member. (Fig. 17)
Continue installing the pipe as required until pipe is installed up through the ceiling. At this point, you must install a firestop spacer.

Pipe Section UP

Pipe Rim

Pipe Hem

Hem Lance

FP1198
Fig. 16 Install pipe, listening for the snap-lock to fasten.

Elbow Strap

Support Structure

Angled Strap

Elbow Strap (must be tight)

Ceiling Hole Framing

Angled Firestop

FP270/271

Chimney Support Strap (must be tight)

Fig. 17 Attach straps to a structural framing member.

20005167

installing the Firestop Spacer in the ceiling hole
A firestop spacer is used to keep pipe spaced properly and required for safety.
Nail the firestop spacer (at each corner) to the framing members of the ceiling hole. NoTE: A firestop spacer is not required at the roof.
Hole sizes listed in Figure 9 for angled firestop spacers provide minimum required air space to chimney pipe for ceiling thickness up to 8″ (203 mm). When combined thickness of ceiling material, ceiling joists and flooring material exceeds 8″ (203 mm), adjustments must be made in framing to assure that minimum air spaces to chimney are maintained.
proper Firestop Spacer installation
Figure 18 shows different installation procedures for both an area that is an attic and an area that is not an attic.
If the area above the ceiling is not an attic, position the firestop spacer with the flange on the ceiling side and the angled portion extending up into the hole.
If the area above the ceiling is an attic, position the firestop spacer with the flange on the top of the framed hole and the angled portion extending down into the hole.
Firestop spacers are not available for, nor are they required on vertical walls.
Do NoT put any sealant around the area where the outer pipe slides through the firestop spacer. If you seal this area, it may cause a fire hazard.

Attic installation

Nails (4)

Firestop Spacer

Joist NoTE: If the attic insulation shield is used, the firestop is not required in the attic installation. ceiling installation
Joist
Firestop Spacer

Nails (4) Fig. 18 Firestop spacer installations.
20005167

FP593

Vermont Castings EWF36A
canadian Requirements for insulation Shield
In Canada, an attic insulation shield is required to prevent attic insulaiton from contacxting the chimney section. NoTE: If the attic insulation shield is used, the firestop is not required in the attic installation. Framing dimensions fr the chimney hole should measure 17¹/” x 17¹/” (445 x 445 mm). An attic shield MUST be installed on top of attic joists (above the floor level). (Fig. 19)
NoTE: In the U.S., it is a good idea, although not always required, to install an attic insulation shield where blown-in insulation is planned to be used in the atic.

Attic Insulation Shield

Nails (4 Required)

Attic Joist

Ceiling

Base Flanges

FP263

Fig. 19 Attic shield installation (Canadian requirement).

continue installing pipe to complete Run

Continue attaching pipe sections to complete system to next level always being careful that the pipe is firmly snapped locked in place before proceeding to next pipe
section.

chimney Supports

If chimney supports are required, they are installed the same as elbows. Nail chimney support straps to adjacent structural framing, as shown on Figure 16. Bend straps as necessary and make sure they are secure so they will support the weight of the chimney. A chimney support is 2¹/” (64 mm) long when installed. Consider this dimension when determining how many straight chimney sections are needed.
NoTE: Chimney supports are generally used in long runs in a chase installation.
Additional ceilings

If you encounter additional ceilings, repeat same steps required for first ceiling installation. See firestop illustra-
tion in Figure 18.

13

Vermont Castings EWF36A
penetrating the Roof
Run pipe to roofline. Since chimney system must be vented to the out-of-doors, you must use an approved MHSC termination.
If a chase is used, refer to the installation manual provided with the termination cap.
locate chimney centerpoint on Roof
Use same procedure detailed in locating center point of the flue system.
Drive a nail up through roof at the center point. This will determine center point on outside of the roof.
cut and Frame Roof hole
Size of roof hole varies with the type of chimney termination installed. Refer to installation instructions provided with MHSC chimney termination to find correct size of roof hole.
There must be a 2″ (51 mm) air space between outermost portion of chimney sections and any adjacent combustible surfaces. (Combustible surfaces include burnable materials such as: ceiling members, joists, flooring, combustible insulation and roof structures.)
WARNiNg: Do not pack required air spaces with insulation or other materials.
Mark an outline of the roof hole around the center of the point nail. NoTE: Hole dimensions given in the chimney top installation instructions are horizontal dimensions; therefore, the hole size must be marked on the roof accordingly.
Cover the opening of the installed chimney so debris cannot get into the system.
Cut and frame the hole. It is good practice to use framing lumber that is the same size as the rafters. Install the frame securely because the chimney top and flashing anchored to the frame must be able to withstand heavy winds.
install Remainder of chimney Sections
Since you have already preplanned the height of your termination according to the Ten Foot Rule, continue to install pipe to the predetermined height.
Check the chimney top installation instructions for details on how high above the roof top the chimney sections (all pipes) should extend.
install Top housing or Termination
Follow the installation instructions provided with the chimney termination you have selected.

installing chimney in a chase
Refer to Figure 2, Page 5 for an illustration of a typical chase installation.
cAUTioN: Treatment of firestop spacers and construction of chase may vary with type of building. These instructions are not a substitute for local building codes. You must check your local building codes to determine specific requirements for your city or state. NoTE: Other building materials may be required in addition to MHSC Firestop Spacers.
Finishing
cAUTioN: All joints between the finished wall and the fireplace surround (steel front) must be sealed with noncombustible material to prevent cold air leakage into the room. (Fig. 20)
NoTE: No material may cover black cast face.
Air Space clearances Combustible framing material MUST NOT penetrate AIR SPACE (shaded areas)

2″ (51mm)

Standoff

1″ (25mm) Air Space to Sides

Wall Shield

Firestop 1″ (25mm) Space to Back 1″ (25mm) Air Space to Sides

No material may cover cast face

0″ Clearance to Floor

FP1199

Hearth Extension

Fig. 20 Minimum clearances to combustibles.

14

20005167

Finish Wall
Finish the wall with material of your choice. Do not install a combustible mantel shelf less than 12″ (305 mm) above the firebox grille opening. Do not install a mantel face plate less than 6″ (159 mm) from top of grille opening. (Fig. 20) If a combustible material is used below a flat mantel shelf, consult your local building codes for minimum clearance from top of fireplace opening to bottom of mantel shelf.
All joints (top, bottom and sides) where wall or decorative facing material meets fireplace surround must be completely sealed with a noncombustible material. (Figs. 21 and 25)
NoTE: No side wall protection is required for fireplaces installed at 45° to two (2) side walls (corner installation).

Mantel Shelf

Side view

See mantel drawing for shelf-to-grille dimension Noncombustible Finish Material Only in this Area
Brick Ledge

Finished Wall 2 x 4 Stud Standoff

Cast Front

Top view Fireplace Front (Steel)

2 x 4 Stud

Vermont Castings EWF36A

Combustiible Mantel and Trim

12″ (305mm)
Max.

Finished Wall

156O” (38mm)
12″ (305mm)
Min.
6″ (159mm)
Min.

Header Standoff Noncombustible Material
Brick Ledge GrilleOpening

FP1398

Fireplace Front

Fig. 22 Combustible mantel minimum opening.

156O” Ref.

**

Combustible materials are permitted within a shaded area shown in Figure 26 titled Minimum Wall Clearances

1″ (25mm)

FP1200

Must be sealed with noncombustible material

Fig. 21 Finishing materials placement.

Mantels

The height that a combustible mantel is fitted above the fireplace is dependent on the depth of the mantel. This also applies to the distance between the mantel leg (if fitted) and the fireplace.
For the correct mounting heights and widths, refer to Figures 22 and 23. When using paint or lacquer to finish the mantel, such paint or lacquer must be heat resistant to prevent discoloration.

• 12″ (305mm) from top of grille opening. ** 6″ from top of grille opening.
  Fig. 23 Combustible mantel clearances.

MA81

Side Wall protection

Adjacent combustible side walls that are within minimum dimensions shown in Figure 25 of the fireplace
opening must be protected with MHSC Wall Shield Model SP40 or a specifically built wall shield described in Figure 20.
The special wall shield design described in Figure 20 is an alternate method of adding protection to side walls and can be used in place of the SP40 with the same wall clearances specified for the SP40. Rt must =1.85 minimum.

20005167

15

Vermont Castings EWF36A

Examples of wall shield insulation:
1. Manville – CERAFORM 126, K=.27, 1/2 inches thick
2. EH2416, K = .458, 1 inch thick required.
hearth installation
A hearth extension is required to protect a combustible floor in front of the fireplace. Refer to Figure 26 for minimum dimensions and mounting detail.
NoTE: hearth Extension must not cover the air inlet opening of a fireplace.
The hearth extension described in Figure 26 must be a durable noncombustible material with a minimum (total) Rt value of 1.09; refer to Figure 24 for examples. The overall height (above a combustible floor), depth and width must be as indicated, with the extension centered to the fireplace opening.
The top of insulation must be covered with a non-combustible decorative covering or a piece of .018″ minimum sheet metal, to protect hearth extension material. (Fig. 26)
Secure the hearth extension to the floor to prevent shifting, using trim molding or other similar means at three (3) outer edges. Seal crack between the fireplace hearth and hearth extension with a noncombustible material. (Figs. 25 and 26)
WARNiNg: hearth extension must be installed in accordance with Figure 25. Top of hearth extension must be level with bottom of fireplace.
Alternate noncombustible materials may be used providing the (total) thermal resistance (Rt value) of the alternate material employed is greater than or equal to R = 1.09 Thermal resistance (R) or thermal conductivity (K), may be obtained from manufacturer of the material. Factors are related by the formula K = 1/R. (Fig. 24)
T = given thickness R = thermal resistance for a given thickness (T) K = thermal conductivity

COMMON MATERIALS AND FACTORS

MATERIAL

MINIMUM K* R THICKNESS

EH2416 (CFM Corporation) 0.916 2.18 1.0 in.**

Noncombustible material with a lower R value may be used, provided thickness of material is sufficiently greater to maintain an equivalent (total) thermal resis-
tance (Rt).

Example of Determining hearth Extension Equivalents
To determine the thickness required for any new material:

NEW

K of new material (per inch)

thickness

required =

X of listed

thickness

K of listed material (per inch)

material

Example for common brick
T (new) = 5.0/0.458 x 0.50 in. = 5.46 in. (new required thickness).

Wall Covering Noncombustible Decorative Facing Seal all cracks between fireplace surround (steel) and wall materials with noncombustible material.

2 x 4 Header – Do not notch at standoffs
NoTE: No material may cover black cast face.

Cast Front Noncombustible Decorative Covering
FP1202
Fig. 25 Sealing gaps.

Safety Strips – Must be overlapped 1/2″ minimum

Common Brick 5.0 0.10 5.46 in.**

R Value is for 1/2 inch.

• Units of K = BTU/SQ FT/HR/°F/IN

** Thickness of Listed Material

FP533ADD

Fig. 24 Hearth extension material factors.

16

20005167

Vermont Castings EWF36A

Minimum Wall Clearances

WITH Noncombustible Surround Facing
4″ Brick (Example material)

WITHOUT Noncombustible Surround Facing
Shaded area starts 1/2″ away from edge of unit
4″

E F C
Side Wall

Firebox Opening

E D

A – Min. clearance to combustible perpendicular wall

B – Min. clearance to combustible perpendicular wall when

Side Wall

using noncombustible wall shield*

Combustible material permitted within shaded area.

• Noncombustible wall shield requires 1″ EH2416 insulation (minimum R Value = 1.85) between decorative noncombustible rigid covering and combustible wall. Minimum height and width is 40″ x 40″.
  ** Dimension/degree of angle will vary depending on thickness of noncombustible surround facing.

Minimum Hearth Extension Dimensions
(for On-Site Construction)

G

G

H

NOTE: No material may

cover black cast face. Hearth extension must be

J

flush with bottom of fireplace.

May install noncombustible decorative covering OR .018″ min. sheet metal

Seal cracks between the fireplace and hearth extension with noncombustible material

Fireplace Opening

956O” Required 1″ Min.

Combustible Floor

1″ Min.

“Z” Safety strips

EH2416 or

must overlap

Equal “R” Value 56O” minimum

A

B

C

EWF36A 24″

12″ 17°

610 mm 305 mm

D

E

F

G

H

J

25° 12″

8″

8″

18″

57″

305 mm 203 mm 203 mm 457 mm 1448 mm

Fig. 26 Combustible side wall protection and hearth extension dimensions.

FP1201

20005167

17

Vermont Castings EWF36A
operation
Attach handles
The fallaway handles are used to open and close the front doors. Remove after each use so they will not get hot. Keep in convenient location for each use. (Fig. 27) Assemble the primary air control and damper handles by passing the 3³/” screw through the ceramic shaft and into the bright metal hub. Tighten carefully until snug. Do not overtighten. Ceramic handle could crack. (Fig. 28)

Primary Air Control

Damper

Steel Handle Fallaway Handle
FP1397
Fig. 27 Insert fallaway handles into door handle stubs.
Metal Hub Ceramic Shaft
Screw FP1396
Fig. 28 Assemble primary air control and damper handles.
EWF36A controls
Three controls regulate the performance of the EWF36A fireplace: A primary air control supplies oxygen for the fire, the damper directs air flow within the fireplace and a variable-speed fan control, or rheostat, regulates the warm air flow into the room. (Fig. 29)
primary Air control
A single air control regulates the amount of heat the fire will produce and how long it will burn.

FP1203
Fig. 29 EWF36A controls.
The primary air control is located in the upper left corner of the unit. (Fig. 27) It is the primary source of air for starting, maintaining, and reviving the fire.
Generally, more air entering the fireplace makes the fire burn hotter and faster, while less air prolongs the burn.
The air supply is open to the maximum when the control lever is rotated clockwise, and closed when rotated counterclockwise. To vary the burn rate, adjust the control to the desired position in between these extremes; opening the primary air control makes the unit burn hotter. Closing the control slows the unit down. You may adjust to any position you desire.
The Damper
The damper directs air flow within the fireplace.
The damper is operated by moving the lever located in the upper right corner of the unit. It has two positions: Open to start or revive the fire and closed, for normal operation and to control burn rate. The damper is open when the lever is fully rotated counterclockwise and pulled out and closed when pushed in. When the damper is in the open position, with the lever pulled out, and rotated fully in the clockwise direction, the handle can `telescope’ back without closing the damper or any damper movement. There are no intermediate settings for the damper.
NoTE: Full clockwise or counterclockwise movement of the damper handle is approximately 50°.
NoTE: Always open the damper before opening the doors. Close damper to set burn rate.

18

20005167

The Fan
Heated air from the fireplace is forced into the room by an internal fan. The control for the fan is in the right corner of the unit.
“Off” is to the far left. “High” is just to the right of “Off.” “Low” is to the far right.
Variable adjustment of the fans is possible with any setting between “high” and “low.”
For best results, coordinate fan speed with the setting of the primary air control. For example, when the air control lever is set at “low,” also set the fan at “low.” With the air control set for maximum heat, set the fan at “high.”
glass Doors
The EWF36A is intended for use with the doors fully closed or fully open only when optional spark screen is installed. (Fig. 30) NoTE: When operated with the doors open and spark screen in place, the damper MUST be in the open position.

correct

correct

KT108b

Fig. 30 Correct door position during operation.

Optional Spark Screen

burn only high-quality Wood

The EWF36A is designed to burn natural wood only; do not burn fuels other than that for which it was designed.

You will enjoy the best results when burning wood that has been adequately air-dried. Avoid burning “green” wood that has not been properly seasoned.

The best hardwood fuels include oak, maple, beech, ash, and hickory that has been split, stacked, and airdried outside under cover for at least one year.

For areas that do not have a supply of hardwood, commonly burned softwoods include tamarack, yellow pine, white pine, Eastern red cedar, fir, and redwood. These too should be properly dried. Your EWF36A will accept wood up to 24″ (610 mm). Longer wood pieces work better than short ones.

Wood should be stored under cover to maintain dryness, and should be dried at least six months for optimum heating and fire-viewing performance. Even for short-term storage, however, keep wood a safe distance from the heater and keep it out of the areas around the heater used for refueling and ash removal.

20005167

Vermont Castings EWF36A
Use the Air control Settings that Work best for you
No single air control setting will fit every situation. Each installation will differ depending on the quality of the fuel, the amount of heat desired, and how long you wish the fire to burn. The control setting also depends on your particular installation’s “draft,” or the force that moves air from the stove up through the chimney. Draft is affected by such things as the length, type, and location of the chimney, local geography, nearby obstructions, and other factors. Too much draft may cause excessive temperatures in the fireplace. On the other hand, too little draft can cause backpuffing into the room and/or the “plugging” of the chimney or combustor. How do you know if your draft is excessively high or low? Symptoms of too much draft include an uncontrollable burn or a glowing-red part of the EWF36A front. A sign of inadequate draft is smoke leaking into the room through the stove or chimney connector joints, low heat, and dirty glass. In some newer homes that are well-insulated and weather-tight, poor draft may result from insufficient air in the house. In such instances, an open window near the stove on the windward side of the house will provide the fresh air needed. Another option for getting more combustion air to the stove is to duct air directly from the outside to the stove. In fact, in some areas provisions for outside combustion air are required in all new construction. Your EWF36A is designed so that it is possible to incorporate outside air for combustion. Directions for installing the optional AK-MST outside air ducts are included with the kits and beginning on Page 11 of this instruction. When first using the stove, keep track of the settings of the air controls. You will quickly find that a specific setting will give you a fixed amount of heat. It may take a week or two to determine the amount of heat and the length of burn you should expect from various settings. Most installations do not require a large amount of combustion air, especially if adequate draft is available. Do not for any reason attempt to increase the firing of your heater by altering the air control adjustment range outlined in these directions.
19

Vermont Castings EWF36A
Starting and Maintaining a Wood Fire
burn solid wood fuel only in the EWF36A, and burn it directly on the grate. Do not elevate the fuel. Do not burn coal or other fuels.
Minimize thermal stress by allowing the plates to adjust gradually during an initial break-in fire by following Steps 1-3 below.
WARNiNg: operate your EWF36A only with the doors fully closed. if the door is left partially open, gas and flame may be drawn out of the fireplace opening, creating risks of both fire and smoke.
1. Open the primary air control fully.
2. Open the damper.
3. Lay some crumpled newspapers on the bottom grate. Place on the paper six or eight pieces of dry, finely-split kindling. On the kindling lay two or three larger sticks of split dry wood approximately 1-2″ (25-51 mm).
Do not use chemicals or fluids to start the fire. Do not burn garbage or flammable fluids such as gasoline, naptha, or engine oil.
Also, never use gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or “freshen up” a fire in this heater. Keep all such liquids well away from the heater while it is in use.
4. Light the newspaper and close the door. Gradually build up the fire by adding a few 3-5″ (80-120 mm) diameter splits.
If this is your initial break-in fire, let the fire burn brightly, but not to excess. Control the fire’s intensity by adjusting the air control lever. After an hour or so stop adding wood so that the fire dies out gradually.
For ongoing operation after the initial break-in, continue to add a few sticks at a time of a progressively larger size. Continue until you have a live ember bed at least 2-3″ (51-76 mm) deep. This may take an hour or longer.
cAUTioN: ThE EWF36A iS hoT WhilE iN opERATioN! kEEp chilDREN, cloThiNg, AND FURNiTURE AWAy. coNTAcT MAy cAUSE SkiN bURNS.
NoTE: Some chimneys need to be “primed,” or warmed up, before they will draw sufficiently to open the damper. To correct this situation, roll up a couple pieces of newspaper, place them on top of the kindling and toward the back of the stove, light them, and close the doors. This should heat the chimney enough to initiate a draft.
Once the draft is established, open the front door and light the rest of the fuel from the bottom. Do not light the main bed of fuel until the chimney begins drawing, and repeat the procedure as often as necessary if the initial attempt is unsuccessful.
20

5. Once a good ember bed of at least 2-3″ (51-76 mm) has formed, let the fire burn hot for an additional ten to fifteen minutes.
6. Close the damper and the primary air control to a medium-low setting as described on Page 18. The fire volume will diminish immediately, but the fireplace will continue to heat up. Maintain control of the fire using the primary air control, and remember: reduce the setting for less heat, increase the setting for more heat. Refer to the air control settings information on Page 18 for recommended settings at different burn rates.
Do NoT ovERFiRE ThiS hEATER. Overfiring may cause a house fire, or can result in permanent damage to the stove. If an exterior part of the EWF36A glows, you are overfiring.
Reloading and Reviving a Wood Fire
· Open the damper and set the air control on “High,”
and wait at least fifteen seconds for the draft to increase. Open the door slowly.
· Check the ash level, and empty the ash pan if nec-
essary. Replace the pan.
· Add the fuel, smaller pieces first. If it is necessary
to use wood smaller than the 24″ (610mm) optimum size, be sure to fill the firebox as completely as possible by loading the wood pieces alternately on the left and right. Split wood will fill the firebox more completely and reduce the frequency of reloading.
If you have an ember bed of at least 2-3″ (51-76 mm), leave the thermostat set on “high” for 10-15 minutes. If the ember bed is less than 2-3″ (51-76 mm), you may have to let it burn longer.
Finally, close the damper and adjust the air control and fan speed for your desired heat level.
NoTE: If the charcoal bed is relatively thick and your fuel is well-seasoned, it is possible to add fresh fuel (smaller pieces first), close the door and damper, and reset the air control within five minutes.
Special Tactics for cold-climate heating
The EWF36A is capable of producing in excess of 100,000 Btu’s/hour and heating an area of up to 2,500 sq. ft. (558 sq. m) However, many factors affect heating performance and can influence the extent to which the EWF36A can heat a given area.
A well-insulated home, located in a moderate climate and with the EWF36A Fireplace located centrally in an open floor plan, will be easier to heat than a drafty home in the far north in which the EWF36A is installed on an exterior wall at the end of a long house.
20005167

Different results may be experienced even in the same installation if you switch from burning good, dry wood to wood that is partially rotted or inadequately seasoned.
To compensate for these factors in cold climates, it may be necessary to operate the EWF36A with the air control set to a higher level more of the time.
Remove and Store Ash Safely
Check the ash pan before reloading the stove, and empty if necessary using the following procedure:
· Open the damper. · Open the load door. · Remove the ash pans from under the hearth
brick. The EWF comes with a cover for the ash pan. To install this cover, hold just above the ash pans with the handle on the cover closest to you. Slide the cover onto the top of the pan as you pull the pan out. As the pan slides out, the flange on the back of the cover should slide into the slot in the back of the ash pan and the flange on the front of the cover will slide over the handle on the ash pan. cAUTioN: Do not pull the pan out too far before the cover engages the slot. Ash may contain hot coals and must be treated with extreme care. Hold the covered ash pan with both hands to avoid dropping or spilling the ashes. · Take the pans outdoors and empty the ash into an ash container. · Before replacing the ash pan, clear away any ash that has spilled over the sides and back of the pan. · Replace the ash pans and front door.

Vermont Castings EWF36A
Empty the ash pans regularly, typically every one to three days. The frequency will vary depending on how you operate your EWF36A: If you burn more wood at higher heat output settings, and ash will accumulate faster.
Ash should be removed frequently and placed outdoors in a metal container with a tight-fitting lid. The closed container of ash should be placed on a noncombustible floor or on the ground, well away from all combustible materials, pending final disposal. If the ash is disposed of by burial in soil or otherwise locally dispersed, it should be retained in the closed container until all cinders have thoroughly cooled. Wood ash may be used as a garden fertilizer.
cAUTioN: Never use your household or shop vacuum cleaner to remove ash from the fireplace; always remove and dispose of the ash properly.

20005167

21

Vermont Castings EWF36A

Maintenance

keep your EWF36A Fireplace looking New and Working its best
care of the cast iron Surface
An occasional dusting with a dry rag will keep the painted cast iron of your EWF36A fireplace looking new.
If the paint needs retouching, first allow the surface to cool completely. Wire-brush areas needing to be painted. Touch-up with high temperature stove paint available from your local dealer. Apply the paint sparingly. Two light coats are better than one heavy one.
cleaning the glass
The EWF36A glass system requires a minimum amount of cleaning. Most carbon deposits that accumulate will burn off during hot fires.
Ash residue that accumulates on the glass should be removed periodically to prevent etching. To clean the glass, follow this procedure:
· Be sure the glass is completely cool.
· Cleaning with water will work in most cases. Use a glass cleaner especially made for this purpose only if deposits are especially heavy. (If heavy deposits are a frequent occurrence, however, evaluate your operating techniques.)
· Rinse the glass thoroughly.
· Dry the glass completely.
NoTE: The EWF36A glass is coated with a special material on the outside that helps reflect heat back into the fire chamber. Do not attempt to remove this coating.
Adjust the Door latch periodically
The front door of the fireplace should close securely to prevent accidental opening and should close tightly to prevent air from leaking into the fire chamber. The door handles will be positioned vertically when the door is closed.
Over a period of time, the gasket around the door will compress and the latch may need adjustment. To adjust the handle, follow this procedure (Fig. 31):
1. Loosen the small lock nut with a wrench.
2. Extend the striker screw one turn by turning it with an Allen wrench.
3. Retighten the lock nut, while at the same time holding the striker screw with the Allen wrench to prevent its turning.
Test the door seal. Close the door on a dollar bill and attempt to pull it free. If the bill is freed with little resis-
22

Pawl Small Locking Nut
Large Locking Nut

Striker Screw

Set Screw

Handle Stub

ST531

Fig. 31 Turn the striker screw to tighten or loosen the door latch.
tance, the gasket isn’t snug enough at that spot. Continue to make small adjustments until the setting is right.
If additional adjusting of the latch does not enable the door to seal sufficiently in one area, try “adjusting” the gasket in that area. Pack more cement or a smaller diameter gasket into the channel beneath the gasket so that the main gasket is raised and makes contact with the door frame. This procedure should solve the problem. If the gasket needs replacing, follow the directions beginning on Page 23.

The catalytic Element

This wood heater contains a catalytic combustor, which needs periodic inspection and replacement for proper operation. In the United States, it is against the law to operate this wood heater in a manner inconsistent with the operating instructions in this manual, or if the catalytic element is deactivated or removed.
Under normal operating conditions, the catalytic combustor should remain active for two to six years (depending on the amount of wood burned). However, it is important to monitor the combustor periodically to ensure that it is functioning properly, as well as to determine when it needs to be replaced. A nonfunctional combustor will result in a loss of heating efficiency, and an increase in creosote and emissions.

inspection and cleaning

Inspect the combustor “in place” for fly ash accumulation and physical damage three times per year. Do not remove the combustor unless a more detailed inspection is warranted because of diminished performances as outlined in the next section.

20005167

When to Suspect a combustor problem
The best way to evaluate the performance of your EWF36A’s combustor is to observe the amount of smoke leaving the chimney – both when the combustor has “lighted-off” and when it has not. Follow these steps:
· With a fire going and the combustor properly activat-
ed, with the damper closed to route smoke through it as described in the Operation Section, go outside and observe the smoke leaving the chimney.
· Then, open the stove damper and once again check
the smoke leaving the chimney.
You should see significantly more smoke when the stove damper is open and exhaust does not pass through the combustor. However, be careful not to confuse smoke with steam from wet wood. Steam dissipates in the air quickly; smoke does not.
If this test indicates a problem, consider other possible factors as well, such as the weather or a change in the quality of your fuel. In warm weather, draft is weaker than it is in colder winter weather and fires can burn sluggishly. Small, hot fires are a good solution under these conditions.
Burning “green” (insufficiently seasoned) wood will result in poorer performance than burning properly seasoned fuel. You may have to run your fireplace hotter (more air) to achieve acceptable performance using green or wet wood.
Also consider any changes in your operating routine. Once you have ruled out any other possible causes for a decline in performance, inspect and clean the combustor if necessary.
inspecting the combustor
Use a flashlight and mirror, if necessary, to examine the combustor. If no fly ash or damage is visible, the inspection is complete. If closer examination, cleaning or replacing is needed, go to the next section.
Removing, cleaning or Replacing the combustor
1. Allow fireplace to cool.
2. Tap the left and right wedges back and remove. (Fig. 32)
3. Carefully slide catalyst assembly to the back of the fireplace and out of the retaining brackets.
4. Check the combustor’s honeycomb-like element for a buildup of fly ash. If any is evident, take the combustor outside and clean it by blowing air gently through it. Do not push anything through the honeycomb; do not use compressed air to clear the pas-

Wedge (In Place)

Vermont Castings EWF36A

FP1324

Catalyst

Wedge Catalyst Assembly

Fig. 32 Carefully tap out the wedges, then slide the Catalyst Assembly out of fireplace.

sages. Such abrasion can scrape the thin coating of platinum (the catalyst) off the ceramic base, shortening the catalyst’s life and reducing its effectiveness.
5. Inspect the element for damage or degradation. Although small hairline cracks will not affect performance, the element should be essentially intact. If the element is broken in pieces or has sections missing, it should be replaced. Call your local Vermont Castings authorized dealer for a replacement element.
6. If the element is in good condition and clean, reinstall it in the fireplace.
Operate the stove in your usual manner for two weeks, inspecting the chimney and the chimney connector frequently during this period.
If creosote does not build up as fast, it is likely that the performance change was caused by fly ash deposits on the catalytic element. However, continue the inspections of the chimney system for a few weeks to ensure that proper performance continues.
If you continue to find a significant creosote buildup or if you continue to see excessive smoke form the chimney, the catalytic element will need to be replaced. Contact your nearest Vermont Castings authorized dealer.
NoTE: Use only the replacement catalyst supplied by a Vermont Castings dealer.

how to Replace gaskets

The EWF36A uses rope-type fiberglass gaskets to make a tight seal between some parts. With use, particularly on those parts that move, gaskets can become brittle and compressed and can begin to lose their effectiveness. These will need periodic replacement.
All of the gaskets used are made of fiberglass. The four sizes of replaceable gasket are listed below, along with their application.

20005167

23

Vermont Castings EWF36A

Replaceable Fiberglass gaskets

Gasket Size… …And The Parts It Seals

1/2″ 5/8″ 3/16″ 1/2″ 1/2″ Braided

The door to the front Door to the hearth brick support The glass seal to the door Cat holder to top plate Damper to top plate

Should you need to change a replaceable gasket, wait until the fire is out and the stove has cooled. Be sure to follow the standard safety procedure for working with dusty materials: Wear safety goggles and a dust mask. The procedure for replacing gaskets is the same, regardless of the gasket location. Four easily-accomplished steps are involved:

1. Remove the existing fiberglass gasket by grasping an end and pulling firmly.

2. Use a wire brush or the tip of a screwdriver to clean the channel of any remaining cement or bits of gasket.

3. Apply a thin bead of stove cement to the newlycleaned groove.
4. Pack a new gasket into the groove. Wait until you have placed all but a couple inches from the end before you trim the end to an exact fit.

5. Place door back on fireplace, latch door and keep closed for 1/2 hour to insure cement has set.

Replacing the Door gaskets

Remove the door by lifting it straight up off its hinge pins. Lay it face down on a padded surface.
Follow steps 1-4 as described above.
Replace Damaged Door glass immediately

Do not operate the fireplace with damaged glass door. Use the following procedure for glass replacement.
NoTE: Replace glass only with the replacement glass made for this unit, available from your authorized dealer.
· Remove the door and loosen the retaining clips which
hold the glass to the door frame. Remove clips. Use caution when handling broken glass.
· Examine the gasket that seals the glass to the door
frame. Replace if necessary with gasket obtained from your local Vermont Castings’ Authorized Dealer. See the directions for gasket replacement on Page 23.
· Check the flat surface of the door frame, and clear
away debris if necessary.
· Install the new glass. · Secure the clips, being careful not to overtighten. Be
sure the glass is firmly seated against the gasket.
· Replace door.

24

The chimney System
A clean chimney System is Safer and Works better
Although the combustion system in the EWF36A can reduce creosote formation dramatically, it is not a substitute for regular inspection and cleaning of the chimney and chimney connector.
learn to Recognize — and Avoid — creosote
The EWF36A has been designed to reduce creosote build-up significantly. However, regular chimney inspection and maintenance must still be performed. For safety, good stove performance, and to protect your chimney and chimney connector, inspect your chimney and chimney connector on a regular schedule. Clean the system if necessary. Failure to keep the chimney and connector system clean can result in a serious chimney fire.
When wood is burned slowly, it produces tar, organic vapors and moisture which combine to form creosote. The creosote vapors condense in the relatively cool chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extremely hot fire within the flue system that can damage the chimney and overheat adjacent combustible material. If a significant layer of creosote has accumulated –1/8″ (3 mm) or more — it should be removed to reduce the risk of a chimney fire. If you do experience a chimney fire, act promptly to:
· Close the primary air control lever and the damper
· Get everyone out of the house. · Call the Fire Department. You should inspect the system every two weeks during the heating season as part of a regular maintenance schedule. To inspect the chimney, let the fireplace cool completely. Remove the termination top. Then, using a strong light, sight down into the chimney flue.
Clean the chimney using a specially designed brush the same size and shape as the flue liner. Flexible fiberglass rods are used to run the brush up and down the liner, causing any deposits to fall to the bottom of the chimney where they can be removed by removing the catalyst housing and using a vacuum. Be sure to vacuum the catalyst also.
If you can not do the chimney inspection yourself, contact your local Vermont Castings’ Authorized Dealer, or engage a professional chimney sweep to perform the inspection and cleaning of the chimney.
20005167

The prefabricated chimney used with your fireplace should be cleaned from above using an 8″ round brush and the appropriate number of extension rods for complete access.
The chimney cap first must be removed following the procedure recommended by the manufacturer. After thoroughly cleaning the chimney, reinstall the chimney cap according to the manufacturer’s directions.
Maintenance Schedule
Fireplace: Daily: · Ash should be removed before the level reaches the
top of the pan. Check each time you re-load, or at least once a day. · Keep the area around the fireplace clear of any combustible material. yearly Spring cleaning: · Remove ash from the fire box and replace with a moisture-absorbing material (such as Kitty Litter) to keep the interior of the fireplace dry. · Touch up painted surfaces with black paint.

Vermont Castings EWF36A

20005167

25

Vermont Castings EWF36A

Component Chimney Support Firestop Attic Insulation Shield
Traditional Top Housing
Housing Extension Contemporary Chase Top Termination Contemporary Flashing
Chimney Sections

chimney components
Description Used to support chimney for each of 30′ vertical height and 6′ of angled chimney run Required at each floor level and attic on multi-story installation Used to prevent insulation from coming in contact with the chimney system.Required in Canada. Optional in U.S. Top housing of simulated brick pattern available in red, tan or white. Appropriate adapter is required (8CA). Flashing included. Extends Traditional Top Housing on steep pitched roofs Used to terminate chimney at the top of a chase. Flashing is not included.
Required for Contemporary Round Top termination to prevent rain entry.
Used to build chimney systems.

Chimney Elbows
Round Top Termination Extended Round Top Chase Termination

Used to develop offset chimney systems. Only 30° elbows are available. (Elbows packed 2 per carton – upper and lower elbow set.)
Used to terminate chimney on the roof. Flashing not included.
Used to terminate chimney at the top of a chase. Adapter Kit included. Flashing not included.

Model Number TCS8A
(8″ flue) FS2A (8″ straight flue) FS6A (8″ 30° inclined flue) FS2100HT
S20B (single flue)
202036 (single flue)
SLTS8
8-6-12 with 8″ flue 0 to 6/12 pitch
8-12-12 with 8″ flue (6/12 to 12/12 pitch)
8″ flue 81 (1′ long) 818 (1¹/’ long) 83 (3′ long) 84 (4′ long)
830A-2 (8″ 30° flue)
RLTS8 (8″ flue)
RLTS8L (8″ flue)

26

20005167

Vermont Castings EWF36A

EWF36CLK

EWF36CFTK

52

63

64

65

1

4

5 7

3 6

49 48

62 42 44

41

43

18

2

2

50

56

51

24

45

55

25

26

52

75 11

EWF36CLK 86
15

80

76 39 47

40 46

47 9

16

17

20

13

32 33 31

54

27

19

74 79

34 28
30
29 79

35 74 12

13 74
21

EWF36CLK 73

15

22 16

76 80
EWF36CLK
87 36

24
25 26

10 75
69 68

38 77

Operating
67

Range

24 25

82

85 84 83

88 EWF36S

84 85

14

23

53

37 74

78

26
81 70

83 82

71

24

25

26

5167

MHSC reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice.
EWF36A Fireplace
For unit FA3ECB

Ref. Description 1. Damper 2. Gib 3. Damper Rod 4. Damper rod Clamp 5. CS, Hex hd 3/8-16 x 1¹/” Full Thd 6. .375 Washer 7. Damper Clamp 9. Damper Link Assy.
10. Right Hinge Painted 11. Left Hinge Painted

EWF36A 20005982 20005983 20005984 20005985 1201443 20005980 20005990 20006057 20006302 20006303

Ref. Description 12. Left Door Assy. 13. Pin, Hinge 14. Left, Door Handle Assy. Vert. Nickel 15. Gasket, 5/16 Adhesive Backed 16. Glass Clip 17. Pan Hd. PH 1/4-20 x 3/8 – Blk 18. Primary Rod 19. Nut, Hex Jam 3/8-16 Toplk-Z 20. Glass, Left Door – EPA Front 21. Right Door Assy.

EWF36A 20005212 1201836 5004265 1203591 30001716 1200993 20006095 1203290 20005153 20005213

20005167

27

Vermont Castings EWF36A

EWF36A Fireplace (continued)

Ref. Description

EWF36A

22. Glass Right Door – EPA Front

20005152

23. Right, Door Handle Assy. Vert. Nickel 20006286

24. Damper Steel Handle w/Screw

5004265

25. Handle, Ceramic Blk 2.78 Lg

20006381

26. Ov Hd Sl 1/4-20 x 3/375 Lg

1201294

27. Linkage Assy.

20005307

28. Pawl, Top

20005154

29. Pawl, Bottom

20005155

30. Link, EPA FP Front

20005156

31. CS, Soc But hd 1/4-20 x 5/8 – Blk

1201529

32. Nut, Hex 1/4-20 Plain

1203210

33. 5/16 Shoulder Screw, 1/4-20

20006091

34. SS, Soc 1/4-20 x 1/4 Knl Cup Pt.

1200417

35. 3/8 Shoulder Bolt 5/16 x 1/2

20005202

36. Ash Pan Assy.

20004915

37. Ash Pan Front, Painted

20006300

38. Hearth Brick

20004865

39. Brick Ash Lip Left

20005881

40. Ash Grate Painted

20006299

41. Flame Holder Assy.

20005987

42. Cast Cat Holder

20005992

43. Cast Flamer

20005993

44. Catalyst

20005541

45. Wedge

20005988

46. Andiron, Painted

20006298

47. Firebrick

1601103

48. Front, Upper Right EPA FP Front

20005158

49. Front, Upper Left EPA FP Front

20005159

50. Front, Lower Left – EPA FP Front

20005161

51. Front, Lower Right – EPA FP Front

20005160

52. Lattice, EPA FP – Front

20005162

53. Door, Rt – EPA FP Front

20004742

54. Door, Lt – EPA FP Front

20004741

Ref. Description 55. Air Wash Rt., Painted 56. Air Wash Lt., Painted 57. Basic Upper Rt. (not shown) 58. Basic Upper Lt. (not shown) 59. Basic Lower Rt. (not shown) 60. Basic Lower Lt. (not shown) 61. Hinge Cover (not shown) 62. Gasket 63. Top Cast Plate 64. Damper Gasket 65. Basic Universal 67. Ash Pan Cover 68. Handle, Ash Pan, WW/Encore 69. 1/4-20 x 3/4″ FL Hd Phillips 70. 1/4″ Star Washer – Black 71. Nut, Hex 1/4-20 Plain 73. Brick Ash Lip Right 74. Ring, Jump 75. Hinge Cover 76. 1/4-20 x 1/2″ Phillips Rd Hd Screw 77. Temperature Probe Assy 78. Black Fallaway Handle 79. Gasket 5/8″ Dia. Low-D Blk 80. 1/4-20 x 1″ #8 Hardness 81. Frame & Screen Assy 82. Stud, 3/8-16 x 2.00 83. Spacer 84. Screen Latch 85. 3/8-16 Lock Nut 86. Lt. Gasket 1/2″ Dia. Low-D Blk. 87. Rt. Gasket 1/2″ Dia. Low-D Blk 88. Air Duct Assy

EWF36A 20006296 20006297 20006024 20006025 20006026 20006027 20005994 20006295 20005979 20006072 20006024 20006292 1301254 1200881 1202461 1203210 20006085 1201985 20005994 1200894 20006417 20006382 20006842 20006847 20006612 20006336 20006924 20006337 20006339 20006469 20006474 20005685

28

20005167

Vermont Castings EWF36A

optional Accessories

Fan kit
Fk26 Fan
The FK26 fan helps distribute heated air from within the firebox out into the room. The fan is controlled by a snapstat that turns power on and off as the firebox temperature rises above and falls below a preset temperature. A rheostat provides for variable fan speeds.
Specifications
115 Volt / 60Hz / .75 Amps
Maintenance
The fan itself does not require regular maintenance, however, periodic cleaning of the fan and the surrounding area is required.
installation
1. Place fan assembly at the back of the unit between hearth supports. Attach using velcro strips provided. (Fig. 33)
2. Install thermal sensor (snapstat) on bottom of firebox by sliding between bracket and firebox.
3. Place electronic fan speed control box (rheostat) to side bracket. Fasten fan speed control box with #10 – 24 hex nuts.
4. If the EB-1 receptacle box (Pt. #ZA1200) was correctly connected when the unit was installed, the fan lead can be directly plugged into the EB-1 plug socket. The fireplace, when installed must be electrically connected and grounded in accordance with local codes, with the current cSA c22.1 canadian Electrical code or for US installations, follow local codes and the National Electrical code, ANSi/NFpA No. 70.
Any electrical rewiring of this fan must be completed by a qualified electrician.
Turn off all power before hook up.

Fan

Heat Sensor (Snapstat)

Electrical Box

Fan Speed Switch (Rheostat) Fig. 33 FK26 fan placement.

FP1323

Trim kits

A cast face trim kit and a cast louvre kit are available to enhance the look of your EWF36A fireplace. Installation instructions are included with the kit.

Model

Description

EWF36ACFTK

Cast Face Trim Kit

EWF36ACLK

Cast Louvre Kit

Screen kit

An optional spark screen, EWF36S, is available to allow the fireplace to be operated with the doors fully open.

NoTE: When operated with the doors open and the screen in place, the damper MUST be in the open position.

20005167

29

Vermont Castings EWF36A

30

20005167

Vermont Castings EWF36A

Warranty

limited 3 year Warranty

MhSc warrants that this woodburning stove will be free of defects in material and workmanship for a period of three years from the date you receive it, except that the catalyst, thermostat assembly, handles, glass door panels, cement, and gasketing shall be warranted as described below.
MHSC will repair or replace, at its option, any part found to be defective upon inspection by a Vermont Castings, Authorized Dealer. The customer must return the defective part or the stove, with shipping prepaid, to the Authorized Dealer or pay for any Authorized Dealer in-home travel fees or service charges for in-home repair work. It is the dealer’s option whether the repair work will be done in the customer’s home or in the dealer’s shop. If, upon inspection, the damage is found to be the fault of the manufacturer, repairs will be authorized at no charge to the customer for parts and/or labor.
Any woodburning stove or part thereof that is repaired or replaced during the limited warranty period will be warranted under the terms of the limited warranty for a period not to exceed the remaining term of the original limited warranty or six (6) months, whichever is longer.

limited 1 year Warranty

The following parts of the woodburning stove are warranted to be free of defects in material and workmanship for a period of one year from the date you receive it: The thermostat assembly, handles, glass door panels, cement, and gasketing. Any of these items found to be defective will be repaired or replaced at no charge, upon the return of the part with postage prepaid to a Vermont Castings Authorized Dealer.
Any part repaired or replaced during the limited warranty period will be warranted under the terms of the limited warranty for a period not to exceed the remaining term of the original limited warranty or six (6) months, whichever is longer.

limited catalyst Warranty

The catalyst will be warranted for a six year period as follows: If the original catalyst or a replacement catalyst proves defective or ceases to maintain 70% of its particulate emission reduction activity (as measured by an approved testing procedure) within 24 months from the date the stove is received, the catalyst itself will be replaced free.

From 25 – 72 months a pro-rated credit will be allowed against a replacement catalyst and the cost of labor necessary for its installation at the time of replacement.

For stove purchases made after June 30, 1990, a third year (25 – 36 months) of no charge replacement will be made when combustor failure is due to thermal degradation of the substrate (crumbling of ceramic material). The customer must pay for any in-home travel fees, service charges, or transportation costs for returning the stove to the Authorized Dealer.

Amount of Time Since Purchase 0 – 36 months 37 – 48 months 49 – 60 months 61 – 72 months

Credit Towards Replacement Cost
100% 30% 20% 10%

Any replacement catalyst will be warranted under the terms of the catalyst warranty for the remaining term of the original warranty. The purchaser must provide the following information in order to receive a replacement catalyst under the terms of this limited warranty:

1. Name, address and telephone number. 2. Proof of original purchase date. 3. Date of failure of catalyst. 4. Any relevant information or circumstances regarding determina-
tion of failure. 5. In addition, the owner must return the failed catalyst.

20005167

Exclusions & limitations
1. This product must be installed or serviced by a qualified installer, preferably NFI or WETT (Canada) certified, as prescribed by the local jurisdiction. It must be installed and operated at all times in accordance with the Installation and Operating instructions furnished with the product any alterion, willful abuse, accident or misuse of this product shall nullify this warranty.
2. This warranty is transferable; however, proof of original retail purchase is required.
3. This warranty does not cover misuse of the stove. Misuse includes overfiring which will result if the stove is used in such a manner as to cause one or more of the plates to glow red. Overfiring can be identified later by warped plates and areas where the paint pigment has burned off. Overfiring in enamel fireplaces is identified by bubbling, cracking, chipping and discoloration of the porcelain enamel finish. MHSC offers no warranty on chipping of enamel surfaces. Inspect your woodburning stove prior to accepting it for any damage to the enamel.
4. This warranty does not cover misuse of the stove as described in the Owner’s Guide, nor does it cover an stove which has been modified unless authorized by a MHSC representative in writing. This warranty does not cover damage to the stove caused by burning salt saturated wood, chemically treated wood, or any fuel not recommended in the Owner’s Guide.
5. This warranty does not cover a stove repaired by someone other than a Vermont Castings Authorized Dealer.
6. Damage to the unit while in transit is not covered by this warranty but is subject to a claim against the common carrier. Contact Vermont Castings Authorized Dealer from whom you purchased your stove or MHSC if the purchase was direct. (Do not operate the stove as this may negate the ability to process the claim with the carrier.)
7. Claims are not valid where the installation does not conform to local building and fire codes or, in their absence, to the recommendations in our Owner’s Guide.
8. The salt air environment of coastal areas, or a high-humidity environment, can be corrosive to the porcelain enamel finish. These conditions can cause rusting of the cast iron beneath the porcelain enamel finish, which will cause the porcelain enamel finish to flake off. This warranty does not cover damage caused by a salt air or high-humidity environment.
9. MHSC shall have no obligation to enhance or update any unit once manufactured.
IN NO EVENT SHALL MHSC BE LIABLE FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES. ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, ARE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. THIS WARRANTY SUPERCEDES ALL OTHER ORAL OR WRITTEN WARRANTIES.
Some states do not allow the exclusion or limitations of incidential and consequential damages or limitations on how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you specific rights and you may have other rights which vary from state to state.
how to obtain Service
If a defect is noted within the warranty period, the customer should contact a Vermont Castings Authorized Dealer or MHSC if the purchase was direct with the following information:
1. Name, address, and telephone number of the purchaser. 2. Date of purchase. 3. Serial number from the label on the back. 4. Nature of the defect or damage. 5. Any relevant information or circumstances, e.g., installation,
mode of operation when defect was noted.
A warranty claim will then start in process. MHSC reserves the right to withhold final approval of a warranty claim pending a visual inspection of the defect by authorized representatives.
31

MhSc
149 Cleveland Drive · Paris, Kentucky 40361 www.mhsc.com

References

• Welcome to manufactured.in
• Repair Your Grill: Shop Replacement Parts for 24,880 Models
• Vermont Castings Fireplace Parts - Select From 28 Models

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>