LOEWE 64510D10 BEAM Laser Display Projector User Manual
- August 3, 2024
- LOEWE
Table of Contents
- LOEWE 64510D10 BEAM Laser Display Projector
- Scope of delivery
- Position of the rating plate
- Laser Safety Information
- User Notice
- Safety Instructions
- Safety Precautions:
- Disposal
- EU Declaration of Conformity
- Exterior
- Caution
- Connection Ports
- Remote control button mapping
- Auto Focus
- Keystone Correction
- Bluetooth Connection
- Technical data
- Troubleshooting
- Licenses
- FCC STATEMENT
- Specifications:
- FAQ:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
LOEWE 64510D10 BEAM Laser Display Projector
USER MANUAL
Thank you
For choosing a We. by Loewe product.
We are happy to have you as a customer. At Loewe, we combine the highest
standards of technology, design and user friendliness. Prouct design. The
young brand is closely linked to Loewe’s nearly hunthe future.
With the aim of a safe and long-term fault-free use of the set,
Safety/Warning on the next page.
Scope of delivery
- We. BEAM
- Power supply (USB-C PD)
- USB-C cable
- User Manual
Position of the rating plate
Label with model number and operating voltage can be found on the bottom of
the device Apps
Scan the QR code below with your phone and download the recommended app.
The “my Loewe” app is an entry point to the Loewe world and gives you access to all user manuals for your Loewe products.
Laser Safety Information
Caution
Do not stare into the beam.
As with any bright light source, do not stare into the beam, RGl IEC
62471-5:2015.
The product complies with IEC 60825-1:2014 Class 1 and RGl IEC 62471-5:2015.
Complies with 21 CFR 1040.10 and 1040.11 except for conformance as a Risk Group 1 LIP as defined in IEC62471-5:Ed. 1.0. For more information see Laser Notice No. 57, dated May 8, 2019.
– Notice is given to supervise children and to never allow them to stare into
the projector beam at any distance from the projector.
– Notice is given to use caution when using the remote control for starting
the projector while in front of the projection lens.
– Notice is given to the user to avoid the use of optical aids such as
binoculars or telescopes inside the beam.
User Notice
Read this manual carefully before use, and retain it for future reference.
Illustrations of product, accessories, and user interface in the user manual
are for reference purposes only. Actual product and functions may vary due to
product enhancements.
The symbol is intended to alert you to read the instructions before operating and maintenance in the literature appcopanying the product.
Safety Instructions
Before using the product, make sure to carefully read the following safety instructions.
| This
warning symbol informs the user that this product contains non-insulated
voltage sources that can cause an electric shock. Coming into contact with any
internal component may result in an electric shock.
---|---
| This symbol informs the user to be aware of high temperatures.
| This symbol informs the user that connecting the equipment to a socket-
outlet with earthing connection by means of a power cord.
| This symbol informs the user about important handling and maintenance
related information. Please read this information carefully to ensure proper
use.
| This symbol informs the user to avoid touching this part.
| Transportation Instructions: It is recommended to transport this projector
in its original or similar packaging.
| Preventing Electric Shocks and Fire Hazards:
Only use the provided genuine power adapter.
Unplug the projector from the electrical outlet during thunderstorms or when
it is not being used for a long time, so as to avoid damage caused by a power
surge or lightning strike.
Do not place any flammable objects near this projector so as to avoid fire.
Do not block any of the vents as this may cause heat build-up inside the
projector, and possibly result in a fire.
Do not block the lens when the projector is turned on. Any object placed close
to the lens may get very hot and/or deformed, and may even cause a fire.
Safety Precautions:
Do not place this projector on an unstable platform, stand or ta ble so as to
prevent it from falling and causing serious damage or personal injury.
Do not look directly into the lens when the projector is turned on to avoid
eye damage.
Do not attempt to disassemble this projector as it may contain dangerous high
voltage components. This projector must only be maintained and repaired by a
qualified or authorized technician.
Do not expose this projector to rain or moisture (operating humidity is
20%–80%).
Do not immerse this projector in, nor expose it to water or other liquids.
Immediately unplug the projector if any liquid or object got into its housing,
and have it checked by a qualified technician before using it again.
Do not place this projector in any of the following environments:
- In poorly ventilated or narrow spaces.
- Near devices that produce a strong magnetic field.
- Near devices that produce a strong magnetic field.
- In direct sunlight.
- In extremely hot, cold or humid environments.
- Close to a fire alarm.
Disposal
All products bearing this symbol are waste electr( cal and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste.
Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for t he recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.
Disposal of packaging
EU Declaration of Conformity
Hereby, Loewe Technology GmbH declares that the radio equipment type Loewe
multi.room amp complies with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following Internet address:
https://www.loewe.tv/int/support
This product can be used across all EU member states.
Due to the 5 GHz frequency range of the built-in WLAN module, use in the
following countries is only permitted inside buildings:
Note: Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.
The product Complies with IEC 60825-1:2014 Class 1 and EC 62471-5:2015 Risk Group 2.
Caution:
– Risk of explosion if the battery is replaced by an incorrect type.
– Disposal of a battery into fire or a hot oven, or mechanically crush- ing or
cutting of a battery, that can result in an explosion.
– Leaving a battery in an extremely high temperature surrounding environment
that can result in an explosion or the leakage of flammable liquid or gas.
– A battery subjected to extremely low air pressure that may result in an
explosion or the leakage of flammable liquid or gas.
Exterior
1. Projection lens
2. Light indicator
3. Speaker
4. 1/4″Female Threaded Tripod Mount 6mm*l (suspended ceiling installation
supported)
5. Heat Dissipation Vent
6. On/Off Button
7. Lable Location
Caution
The air vents allow the air to exchange internally and externally. Do not
place any objects within 20 cm of the air vents.
Do not look directly into the lens to avoid eye damage as the projector will
emit strong light during working.
If you plan to mount the projector on a suspended ceiling, make sure to select
the right screws and bracket for it.
Connection Ports
1. On/Off Button
2. USB Port
3. HDMI input Port
4. Headphone Port
5. Type-C Charge Port
Remote control button mapping
Auto Focus
Go to Settings > Picture > Focus and select Execute Focus, the screen will
focus and once it is finished you can press the front or back button on the
remote control for further fine-tuning.
Go to Settings> Picture> Focus and select the Auto Focus switch, when it is
enabled, moving the projector will automatically trigger the screen to focus.
Note:
The menu page will be updated from time to time, and the current app version
shall prevail.
Keystone Correction
Go to Settings> Picture> Keystone Correction, and use the up and down buttons
to select Quick Adjustment, Fine Tuning, and Reset, then press the OK button
to enter the correction mode.
Go to Settings > Picture > Keystone Correction, to configure Auto Keystone.
Auto Keystone is enabled by default.
If the projector is moved, it will start automatic keystone correction and the
projected image will be adjusted automatically.
Bluetooth Connection
Technical data
Troubleshooting
Licenses
ALPI
The ALPD® word mark and logos are registered trademarks owned by Appotronics
Co., Ltd., and any use of such marks by Loewe Technology
GmbH is under license. Other trademarks and trade names are those of their
respective owners.
Dolby Audio
Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and
the double-D symbol are trademarkso f Dolby Laboratories
Licensing Corporation.
Bluetooth’
The Bluetooth® word mark and logos are registered trademarks of Bluetooth SIG
Inc. and any use of such marks by Loewe Technology GmbH takes place under
license. Other trademarks and trade names are those of their respective
owners.
HDMI
The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HOMI Licensing Administrator, Inc.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Important: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure Information: The radiated output power of this device meets the limits of FCC/IC radio frequency exposure limits. This device should be operated with a minimum separation distance of 20cm (8 inches) between the equipment and a person’s body.
This device complies with Innovation, Science, and Economic Development Canad licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
5GHz band(W52, W53): Indoor use only
Sande 5 GHz (W52, W53): utilisation interieure uniquement
Local Loewe Service partner
Specifications:
-
Product Name: We. BEAM Laser Display Projector
-
ArtNo.: 64510D10
-
Compliance: IEC 60825-1:2014, IEC/EN 62471-5:2015
-
Class: Class 1 Laser Product
-
-
FAQ:
Q: Can children use the projector unsupervised?
A: No, it is important to supervise children to prevent them from staring into the projector beam.
Q: How can I adjust the focus of the projector?
A: Utilize the Auto Focus feature in the menu settings for optimal image clarity.