PHILIPS AVENT SCY946-01 Natural Response PPSU Baby Bottle Instruction Manual
- August 2, 2024
- PHILIPS AVENT
Table of Contents
PHILIPS AVENT SCY946-01 Natural Response PPSU Baby Bottle
INSTRUCTION MANUAL
BABY BOTTLE
Read all instructions carefully before use. Keep the user manual and product packaging for future reference.
For your child’s safety and health
WARNING!
– Continuous and prolonged sucking of fluids will cause tooth decay.
– Always check food temperature before feeding.
– Throw away at the first signs of damage or weakness.
– Keep components not in use out of the reach of children.
– Never attach to cords, ribbons, laces or loose parts of clothing. The child
can be strangled.
– Never use feeding teats as a soother.
– Glass bottles may break.
– Always use this product with adult supervision.
It is not recommended to use a microwave to warm up baby food or drinks. Microwaves may destroy valuable nutrients in food/drinks and may produce localized high temperatures. If you decide to use the microwave, take extra care to stir heated food/drinks to ensure even heat distribution and check the temperature before serving. Only place the container in the microwave, without the screw ring, teat and cap. Do not allow children to play with small parts or walk/run while using bottles. Always discard any breast milk that is left over at the end of a feed. Inspect before each use and pull the feeding teat in all directions. Throw away at the first signs of damage or weakness. Do not use metal inside the glass bottle to stir contents or for cleaning. This can damage the glass. Do not use bottles if there are any cracks on or glass fragments in the bottle. Do not use bottle handles with glass bottles. Prolonged wear or development of scratches may lead to breakage.
Before first use
Disassemble all parts, clean and then sterilize the parts by placing in boiling water for 5 minutes or sterilize by using a Philips Avent sterilizer. This is to ensure hygiene.
Assembly
Make sure that the feeding teat is fully pulled through the screw ring as shown in the image (Fig. 1, 2).
Cleaning and storage
Clean all parts before each use to ensure hygiene. After each use, disassemble all parts, wash in warm, soapy water, remove any food residues and rinse thoroughly. If you use a brush to clean the tip of the feeding teat, clean it as carefully as possible to avoid damage. Then sterilize using a Philips Avent sterilizer or boil for 5 minutes. Make sure that you wash your hands thoroughly and that the surfaces are clean before contact with sterilized components. During sterilization with boiling water, prevent the parts from touching the side of the pot. This can cause irreversible product deformation, defect or damage that Philips cannot be held liable for. Food colorings may discolor parts. This product is dishwasher safe.
Do not place the product in a heated oven. Do not bring the bottle parts in contact with or place on surfaces with abrasive or antibacterial cleaning agents. We recommend replacing feeding teats every 3 months. Keep feeding teats in a dry, covered container. Do not leave a feeding teat in direct sunlight or heat, or leave in disinfectant (sterilizing solution) for longer than recommended, as this may weaken the teat.
Compatibility
Replacement teats are available separately. To learn more about choosing the right teat for your baby, visit us at www.philips.com/avent. These bottle parts are compatible only with Philips Avent Natural teats.
Support
If you need information or support, please visit
www.philips.com/support.
www.philips.com/avent
Philips Consumer Lifestyle B.V.
Tussendiepen 4, 9206 AD Drachten, The Netherlands Trademarks are the property
of Koninklijke Philips N.V. © 2024 Koninklijke Philips N.V.
All rights reserved.
3000.133.9729.1 (27/02/2024)
Specifications:
- Product Name: Baby Bottle
- Manufacturer: Philips Avent
- Compatibility: Only compatible with Philips Avent Natural teats
Product Usage Instructions
Before First Use
1. Disassemble all parts of the baby bottle.
2. Clean all parts thoroughly.
3. Sterilize the parts by either boiling them in water for 5 minutes or using a Philips Avent sterilizer to ensure hygiene.
Assembly
1. Make sure the feeding teat is fully pulled through the screw ring as shown in the provided image (Fig. 1, 2).
Compatibility
Replacement teats are available separately. Visit www.philips.com/avent to learn more about choosing the right teat for your baby. Remember, these bottle parts are only compatible with Philips Avent Natural teats.
Support
If you need any information or support, please visit
www.philips.com/support.
FAQ
Q: How should I clean the baby bottle before first use?
A: Disassemble all parts, clean them thoroughly, and sterilize by boiling in water for 5 minutes or using a Philips Avent sterilizer.
Q: Can I use other brands of teats with this baby bottle?
A: No, these bottle parts are only compatible with Philips Avent Natural teats.
References
- Baby Care Products, Accessories & Baby Essentials | Share the Care
- Philips Customer Service Support - Home | Philips