Beat-Sonic BSA21EP Smartphone Holder Instruction Manual

July 31, 2024
Beat-Sonic

BSA21EP Smartphone Holder

“`html

Product Information

Specifications

  • Stand Dimensions: 65mm(W) x 230mm(H) x 48mm(D)
  • Material: ABS Plastic
  • Holder Dimensions: 73mm(W) x 95mm(H) x 45mm(D)
  • Material: ABS Plastic

Product Usage Instructions

1. Attach the Stand

1.1 Temporarily remove the factory cup holder. Insert the Lower
Bracket into the front cup holder receptacle ensuring the plastic
locating hooks attach securely to the upper edge of the
receptacle.

1.2 Remove the double-sided tape backing film from the Center
Bracket. Holding the Lower Stand in place, slide the Center Bracket
over the Lower Bracket so that the double-sided tape contacts the
center console. Apply medium pressure for at least 20 seconds to
ensure strong adhesion of the double-sided tape.

1.3 Position the Upper Arm onto the Center Bracket. Insert the
Center Bolt through the Upper Arm to secure in place. Adjust
desired position of the Upper Arm before tightening the Center
Bolt.

2. Attach the Holder

2.1 Attach the smartphone holder to the stand using the
L-Bracket. Complete the installation by reinstalling the factory
cup holder.

2.2 If the holder does not fit tightly to the L-Bracket, apply
1~2 pieces as required of the supplied packing stickers to the back
of the holder. The stickers act as shims to remove any play.

3. Using the Holder

3.1 Inserting the Phone: Release the holder arms by pressing the
release button located on the lower right of the holder.

3.2 Securing the Phone: Press the arms inwards to secure the
phone in place. The fold-out lower stand can be used to provide
additional stability.

FAQ

Q: What should I do if extreme temperature changes and road

vibrations loosen the stand joints?

A: Periodically check and tighten the stand joints if necessary
to ensure stability.

Q: Is it safe to use my mobile device while driving with this

product installed?

A: Follow local driving regulations regarding cell phone use
while operating a vehicle and ensure that your mobile device does
not interfere with safe driving practices.

“`

Phone Holder

/0
BSA21EP Instruction Manual

Thank you for purchasing the Beat-Sonic BSA21EP mobile device holder. Designed and made in Japan, this product represents our commitment to quality and excellence. Please read this manual carefully prior to installing this product to ensure correct operation.
Features
Designed specifically for the ND series Mazda MX-5 / Miata / Roadster. Secure mounting position that does not obstruct visibility or block air vents. Attaches to front cup holder receptacle while retaining the factory cup holder. “L-Bracket” design provides the option to attach a variety of Beat- Sonic mobile device holders.

L-Bracket

Adjustment Knob

Center Bolt

2 Attach the Holder
2.1 Attach the smartphone holder to the stand using the L-Bracket. Complete the installation by reinstalling the factory cup holder.

Upper Arm

Center Bracket

Holder

Stand

Lower Bracket

Precautions
Adjust Carefully: Ensure the mobile device does not interfere with the gear shift lever operation. Check Regularly: Extreme temperature changes and road vibrations may loosen the stand
joints. Periodically check and tighten if necessary.
Obey Traffic Laws: Follow local driving regulations, including those related to cell phone use while operating a vehicle.
Disclaimer: Beat-Sonic and its affiliates are not responsible for any consequences resulting from the installation and/or use of this product.

Specifications
Stand Dimensions: – 65mm(W) x 230mm(H) x 48mm(D) – Material: ABS Plastic

Holder Dimensions: – 73mm(W) x 95mm(H) x 45mm(D)
– Material: ABS Plastic

Contents
– LHD Mazda MX-5 / Miata Stand x 1 – Smartphone Holder x 1

– L-Bracket Stickers x 2 – Instruction Manual x 1

2.2 If the holder does not fit tightly to the L-Bracket, apply 1~2 piece as required of the supplied packing stickers to the back of the holder. The stickers act as shims to remove any play.
L-Hook In case of loose fitment
Affix the packing stickers as required

1 Attach the Stand
1.1 Temporarily remove the factory cup holder. Insert the Lower Bracket into the front cup holder receptacle ensuring the plastic locating hooks attach securely to the upper edge of the receptacle.

3 Using the Holder
3.1 Inserting the Phone: Release the holder arms by pressing the release button located on the lower right of the holder.

Locating hooks

Upper edge of cup holder receptacle

1.2 Remove the double-sided tape backing film from the Center Bracket. Holding the Lower Stand in place, slide the Center Bracket over the Lower Bracket so that the double-sided tape contacts the center console. Apply medium pressure for at least 20 seconds to ensure strong adhesion of the double sided tape.
Remove backing film
Center Bracket

1.3 Position the Upper Arm onto the Center Bracket. Insert the Center Bolt through the Upper Arm to secure in place. Adjust desired position of the Upper Arm before tightening the Center Bolt.

Fold-out lower stand
3.2 Securing the Phone: Press the arms inwards to secure the phone in place. The fold-out lower stand can be used to provide additional stability.

Release button

International
472-5 Koushin, Fujieda, Nisshin, Aichi, 470-0112, JAPAN TEL: +81-561-75-1655 FAX: +81-561-74-5595 www.beatsonicglobal.com email: inquiries@beatsonicglobal.com

USA and Canada

Beat-Sonic USA Inc.

14778 Beach Blvd. La Mirada, CA 90638 TEL: 1-714-994-1085 FAX: 1-714-249-4741 www.beatsonicusa.com email: info@beatsonicusa.com

The rights to the trademarks, logos, trade names etc. herein belong to the respective owners. Refer to the Beat-Sonic website for details.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals