Beat-Sonic BS A21 Phone Holder Instruction Manual
- July 31, 2024
- Beat-Sonic
Table of Contents
BS A21 Phone Holder
“`html
Specifications
Stand Dimensions: – 65mm(W) x 230mm(H) x 48mm(D) – Material: ABS
Plastic
Holder Dimensions: – 73mm(W) x 95mm(H) x 45mm(D) – Material: ABS
Plastic
Product Information
Features:
-
Designed specifically for the ND series Mazda MX-5 / Miata /
Roadster. -
Secure mounting position that does not obstruct visibility or
block air vents. -
Attaches to front cup holder receptacle while retaining the
factory cup holder. -
L-Bracket design provides the option to attach a variety of
Beat-Sonic mobile device holders.
Precautions:
-
Adjust Carefully: Ensure the mobile device does not interfere
with the gear shift lever operation. -
Check Regularly: Extreme temperature changes and road
vibrations may loosen the stand joints. Periodically check and
tighten if necessary. -
Obey Traffic Laws: Follow local driving regulations, including
those related to cell phone use while operating a vehicle.
Product Usage Instructions
Attach the Stand
-
Temporarily remove the factory cup holder.
-
Insert the Lower Bracket into the front cup holder receptacle
ensuring the plastic locating hooks attach securely to the upper
edge of the receptacle. -
Remove the double-sided tape backing film from the Center
Bracket. Slide the Center Bracket over the Lower Bracket so that
the double-sided tape contacts the center console. Apply medium
pressure for at least 20 seconds to ensure strong adhesion. -
Position the Upper Arm onto the Center Bracket. Insert the
Center Bolt through the Upper Arm to secure in place. Adjust
desired position before tightening the Center Bolt.
Attach the Holder
-
Attach the smartphone holder to the stand using the L-Bracket.
Reinstall the factory cup holder. -
If the holder does not fit tightly, apply packing stickers as
shims to remove any play.
Using the Holder
-
Inserting the Phone: Release the holder arms by pressing the
release button located on the lower right of the holder. -
Securing the Phone: Press the arms inwards to secure the phone
in place. The fold-out lower stand can be used for additional
stability.
FAQ
Q: What should I do if the holder is loose?
A: Apply 1~2 pieces of the supplied packing stickers to the back
of the holder to ensure a tight fit.
Q: How do I adjust the position of the phone holder?
A: Position the Upper Arm onto the Center Bracket and adjust
before tightening the Center Bolt.
“`
BSA21 Phone Holder
/0
Instruction Manual
Thank you for purchasing the Beat-Sonic BSA21 mobile device holder. Designed
and made in Japan, this product represents our commitment to quality and
excellence. Please read this manual carefully prior to installing this product
to ensure correct operation.
Features
Designed specifically for the ND series Mazda MX-5 / Miata / Roadster. Secure
mounting position that does not obstruct visibility or block air vents.
Attaches to front cup holder receptacle while retaining the factory cup
holder. “L-Bracket” design provides the option to attach a variety of Beat-
Sonic mobile device holders.
L-Bracket
Center Bolt
2 Attach the Holder
2.1 Attach the smartphone holder to the stand using the L-Bracket. Complete
the installation by reinstalling the factory cup holder.
Upper Arm
Adjustment Knob
Center Bracket
Stand
Holder
Lower Bracket
Precautions
Adjust Carefully: Ensure the mobile device does not interfere with the gear
shift lever operation. Check Regularly: Extreme temperature changes and road
vibrations may loosen the stand
joints. Periodically check and tighten if necessary.
Obey Traffic Laws: Follow local driving regulations, including those related
to cell phone use while operating a vehicle.
Disclaimer: Beat-Sonic and its affiliates are not responsible for any
consequences resulting from the installation and/or use of this product.
Specifications
Stand Dimensions: – 65mm(W) x 230mm(H) x 48mm(D) – Material: ABS Plastic
Holder Dimensions: – 73mm(W) x 95mm(H) x 45mm(D)
– Material: ABS Plastic
Contents
– RHD Mazda MX-5 / Miata Stand x 1 – Smartphone Holder x 1
– L-Bracket Stickers x 2 – Instruction Manual x 1
2.2 If the holder does not fit tightly to the L-Bracket, apply 1~2 piece as
required of the supplied packing stickers to the back of the holder. The
stickers act as shims to remove any play.
L-Hook In case of loose fitment
Affix the packing stickers as required
1 Attach the Stand
1.1 Temporarily remove the factory cup holder. Insert the Lower Bracket into
the front cup holder receptacle ensuring the plastic locating hooks attach
securely to the upper edge of the receptacle.
3 Using the Holder
3.1 Inserting the Phone: Release the holder arms by pressing the release
button located on the lower right of the holder.
Upper edge of cup holder receptacle
Locating hooks
1.2 Remove the double-sided tape backing film from the Center Bracket. Holding
the Lower Stand in place, slide the Center Bracket over the Lower Bracket so
that the double-sided tape contacts the center console. Apply medium pressure
for at least 20 seconds to ensure strong adhesion of the double sided tape.
Remove backing film
Center Bracket
1.3 Position the Upper Arm onto the Center Bracket. Insert the Center Bolt through the Upper Arm to secure in place. Adjust desired position of the Upper Arm before tightening the Center Bolt.
Fold-out lower stand
3.2 Securing the Phone: Press the arms inwards to secure the phone in place.
The fold-out lower stand can be used to provide additional stability.
Release button
International
472-5 Koushin, Fujieda, Nisshin, Aichi, 470-0112, JAPAN TEL: +81-561-75-1655
FAX: +81-561-74-5595 www.beatsonicglobal.com email:
inquiries@beatsonicglobal.com
USA and Canada
Beat-Sonic USA Inc.
14778 Beach Blvd. La Mirada, CA 90638 TEL: 1-714-994-1085 FAX: 1-714-249-4741 www.beatsonicusa.com email: info@beatsonicusa.com
The rights to the trademarks, logos, trade names etc. herein belong to the respective owners. Refer to the Beat-Sonic website for details.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>