Beat-Sonic BSA62 Smartphone Holder Instruction Manual
- June 27, 2024
- Beat-Sonic
Table of Contents
Beat-Sonic BSA62 Smartphone Holder
Thank you for purchasing the Beat-Sonic BSA62 Mobile Device Holder. Designed and made in Japan, this product represents our commitment to quality and excellence. Please read this manual carefully prior to installing this product to ensure correct operation.
Features
- Designed specifically for ZN8 Toyota GR86 & ZD8 Subaru BRZ
- Secure mounting position does not obstruct visibility or block air vents
- “L-Bracket” provides option to attach a variety of Beat-Sonic mobile device holders
Precautions
- Adjust the stand so that the mobile device does not interfere with the operation of the gear shift lever.
- Extreme changes in temperature and harsh vibrations may cause the joints of the stand to work loose. Periodically check the stand and holder are correctly secured and tighten as necessary.
- Beat-Sonic and its affiliates shall not be held responsible for any consequence, either directly or indirectly, as a result of installing and/or using this product.
Specifications
- Stand Dimensions: 85mm(W) x 212mm(H) x 52mm(D)
- Holder Dimensions: 99mm(W) x 91mm(H) x 13mm(D)
- Material: ABS Plastic
Contents
- LHD GR86 / BRZ Stand x 1
- Self Closing Smartphone Holder x 1
- Protective Film × 2
- L-Bracket Stickers × 2
- Plastic Tweezers x 1
- Paper Template x 1
- Instruction Manual x 1
INSTALLATION STEPS
- Step 1. Apply anti-scratch protective film
- Parallel to the edge of the passenger side gear shift surround trim, measure 14cm (5.5 in.) from the panel seam where the shift surround panel meets the center console box. Mark the location with masking tape.
- On the lower section of the passenger side center console side panel, measure 9.5cm (3.74 in.) from the seam where the center console side panel joins the center console box. Apply another piece of masking tape to mark the location.
- Apply the clear protective film strips to the plastic trim forward of the masking tape position markers as shown in the above illustration, then remove the masking tape markers.
- Step 2. Attach the paper template
- Cut out the supplied paper template. Align the back edge of the template with the seam where the center console side panel joins the center console box. Use masking tape to temporarily hold in place.
- Remove the double-sided tape backing film from the stand. Using the template as a guide, (a) clip the lower edge of the stand under the center console side panel then (b) clip the upper section of the stand over the gear shift surround trim.
- Apply medium pressure to the side of the stand for at least 20 seconds to ensure strong adhesion of the double-sided tape. In cold weather use a hair dryer to warm the mating surfaces.
- Step 3. Attach the holder
- Complete the installation by attaching the mobile device holder to the stand.
- If the holder does not fit tightly to the L-Bracket, apply 1 ~ 2 pieces as required of the supplied packing stickers to the back of the holder. The stickers act as shims to remove any play.
- Step 4. Using the holder
- Insert the phone by lowering it into the holder
- The weight of the phone will push down on the lower arm and the side arms will automatically close to securing the phone in place
- To remove the phone simply slide the phone upwards to release the arms
- This holder design allows some movement of the phone even when the arms are closed. This is not a defect and is inherent to the design of this holder.
PACKING
CONTACT
- International
- 472-5 Koushin, Fujieda, Nisshin, Aichi, JAPAN.
- TEL: +81-561-75-1655
- FAX: +81-561-74-5595
- www.beatsonicglobal.com
- email: inquiries@beatsonicglobal.com.
- USA and Canada
- 14778 Beach Blvd. La Mirada, CA 90638
- TEL: 1-714-994-1085
- FAX: 1-714-249-4741
- www.beatsonicusa.com.
- email: info@beatsonicusa.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>