Honeywell CT37 Series HC Mobile Computer User Guide
- August 23, 2024
- Honeywell
Table of Contents
- Honeywell CT37 Series HC Mobile Computer
- Product Information
- Product Usage Instructions
- Out of the Box
- Memory Card Specifications
- Computer Features
- Install a Nano SIM Card (WWAN Models)
- About the Battery
- Install the Hand Strap (SKU Dependent)
- Charge the Mobile Computer
- Turn Power On/Off
- Screen Timeout
- Navigation and Function Buttons
- Sync Data
- Restart the Mobile Computer
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Honeywell CT37 Series HC Mobile Computer
Product Information
Specifications
- Model: CT37 Series
- Operating System: AndroidTM
- Memory Card Compatibility: Single Level Cell (SLC) industrial grade microSDTM, microSDHCTM, or microSDXCTM
- Battery Type: Li-ion
- Charging Time: Minimum of 3 hours with CT37 charging device
Product Usage Instructions
Memory Card Installation
- Ensure the device is powered off.
- Insert the compatible memory card into the designated slot.
- Contact Honeywell for guidance on qualified memory card options.
Battery Installation
- Locate the battery latch and unlock it.
- Insert the Li-ion battery provided by Honeywell.
Hand Strap Installation
Depending on the version you have, follow the appropriate steps for installing
the hand strap.
Charging the Mobile Computer
Charge the device using a CT37 charging device for a minimum of 3 hours before
initial use. Avoid using the device while charging to expedite the charging
process.
FAQ
-
Q: What type of memory cards are recommended for use with the CT37 Series?
A: Honeywell recommends Single Level Cell (SLC) industrial grade microSDTM, microSDHCTM, or microSDXCTM memory cards for optimal performance and durability. -
Q: How long should I charge the battery before initial use?
A: Charge the battery for a minimum of 3 hours using a CT37 charging device that comes with the mobile computer.
Agency Models
CT37 Series: CT37X0N, CT37X1N
Note: Due to variations in model configurations, your computer may appear
different than illustrated.
Out of the Box
Make sure that your shipping box contains these items:
- Standard SKUs:
- CT37 mobile computer
- Rechargeable Li-ion battery
- Standard hand strap
- Product Documentation
- Healthcare SKUs:
- CT37 mobile computer
- Rechargeable Li-ion battery
- USB Type C plug (SKU dependent, pre-installed)
- Product Documentation
If you ordered accessories for your mobile computer, verify that they are also
included with the order. Be sure to keep the original packaging in case you
need to return the mobile computer for service.
Note: CT37X0N models do not include a WWAN radio.
Memory Card Specifications
Honeywell recommends the use of Single Level Cell (SLC) industrial grade microSD™, microSDHC™ or microSDXC™ memory cards with mobile computers for maximum performance and durability. Contact a Honeywell sales representative for additional information on qualified memory card options.
Computer Features
Note: Due to variations in model configurations, your computer may appear different than illustrated.
Install a Nano SIM Card (WWAN Models)
Either a nano-SIM card or embedded SIM (eSIM) is used to activate the phone and connect to a mobile network. Refer to the user guide for additional information.
Note: Always power off the computer before attempting to install or remove a nano-SIM card.
Install a microSD Card (Optional)
Note: Format the microSD card before initial use.
Note: Always power off the computer before attempting to install or remove a microSD card.
About the Battery
The mobile computer ships with a Li-ion battery manufactured for Honeywell International Inc.
- Before you attempt to use, charge or replace the battery in the device, carefully read all labels, markings and product documentation provided in the box or online at sps.honeywell.com. To learn more about Battery Maintenance for Portable Devices, go to honeywell.com/PSS-BatteryMaintenance.
- We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in damage not covered by the warranty.
- Ensure all components are dry prior to placing the battery in the computer. Mating wet components may cause damage not covered by the warranty.
Install Battery
Install the Hand Strap (SKU Dependent)
Standard Version
Note: See page 11 for Healthcare hand strap version (sold separately).
Healthcare Version (Sold Separately)
Note: The optional hand strap for healthcare models is intended for use in environments where cleaning and disinfecting are performed.
Charge the Mobile Computer
The mobile computer ships with a partially charged battery. Charge the battery
before initial use with a CT37 charging device for a minimum of 3 hours.
Note: Using the computer while charging the battery increases the time
required to reach a full charge. If the mobile computer is drawing more
current than supplied by the charging source, charging will not take place.
We recommend the use of Honeywell accessories and power adapters. Use of any
non-Honeywell accessories or power adapters may cause damage not covered by
the warranty.
CT37 series mobile computers are designed for use with CT37 charging accessories. For more information, see the CT37 Accessory Guide available for download at sps.honeywell.com.
Ensure all components are dry prior to mating the computers and batteries with peripheral devices. Mating wet components may cause damage not covered by the warranty.
About the USB Type C Connector
You can use a USB cable to charge the mobile computer from a host device
(e.g., laptop or desktop computer). The connected host device must supply a
minimum power output of 5V, 0.5A to the CT37 or the battery will not charge.
Note: On Healthcare SKUs, verify the USB Type C plug has been removed
before attempting to attach a cable to the USB connector.
About the USB Type C Plug
Healthcare models include a protective plug for the USB Type C connector that
is pre-installed. When your reinstall the plug, make sure the plug is flush
with the body of the computer.
Note: Do not use sharp or metallic instruments to install or remove the
plug.
Note: Verify the plug is properly installed if intermittent charging and/or communication issues occur when the computer is placed in an accessory.
Turn Power On/Off
Note: Charge the battery before initial use with a CT37 charging device
for a minimum of 3 hours.
The first time you power on the computer, a Welcome screen appears. You can
either scan a configuration barcode or use the Wizard to manually set up the
computer. Once setup is complete, the Welcome screen no longer appears on
startup and Provisioning mode is automatically turned off (disabled).
To turn the computer on:
- Press and hold th ePower button for approximately 3 seconds and then release.
To turn the computer off:
- Press and hold the Power button until the options menu appears.
- Touch Power Off.
Battery Replacement, Hot Swap
The computer includes an internal battery that provides limited power for on
demand replacement of the main battery (i.e., hot swap).
You can replace the battery on demand provided the following conditions are
met:
- The internal battery is charged (see note).
- You insert a charged battery within 60 seconds.
- Refer to the user guide for additional guidance on use of the battery hot swap feature.
Note: The internal battery is charged via the main battery but can be depleted if too many consecutive hot swaps occur over a short time. If a low internal battery notification displays, do not perform a hot swap until the notification clears. The internal battery is not user replaceable.
Note: Do not install or remove the microSD card or nano-SIM card while performing a hot swap.
Screen Timeout
The screen timeout (sleep mode) automatically turns the touch panel display off and locks the computer to save battery power when the computer is inactive for a programmed period of time.
- Press and release the Power button to wake the computer.
Adjust the Screen Timeout
To adjust the amount of time before the display sleeps after inactivity:
- Swipe up on the touch screen.
- Select Settings > Display > Screen Timeout.
- Select the amount of time before the display goes to sleep.
About the Home Screen
Navigation and Function Buttons
For button locations, see Computer Features on page 3.
About Provisioning Mode
After completing the out-of-box set up process, Provisioning mode is
automatically turned off. Scanning a barcode to install applications,
certificates, configuration files, and licenses on the computer is restricted
unless you enable Provisioning mode in the Settings app. To learn more, see
the user guide.
Scan a Barcode with the Scan Demo
For optimum performance, avoid reflections by scanning the barcode at a slight
angle.
- Swipe up on the screen.
- Select Demos > Scan Demo.
- Point the computer at the barcode.
- Touch Scan on the screen or press and hold any Scan button. Center the aiming beam over the barcode.
The decode results appear on the screen.
Note: In the Scan Demo app, not all barcode symbologies are enabled by
default. If a barcode does not scan, the correct symbology may not be enabled.
To learn how to modify the default app settings, see the user guide.
Sync Data
To move files between your CT37 and a computer:
- Connect the CT37 to your computer using a USB charge/communication accessory.
- On the CT37, swipe down from the top of the screen to see the notifications panel.
- Touch the Android System notification twice to open the options menu.
- Select either File Transfer or PTP.
- Open the file browser on your computer.
- Browse to the CT37. You can now copy, delete, and move files or folders between your computer and CT37 as you would with any other storage drive (e.g., cut and paste or drag and drop).
Note: When Provisioning mode is turned off, some folders are hidden from view in the file browser.
Restart the Mobile Computer
You may need to restart the mobile computer to correct conditions where an application stops responding to the system or the computer seems to be locked up.
- Press and hold the Power button until the options menu appears.
- Select Restart.
To restart the computer if the touch panel display is unresponsive:
- Press and hold th ePower button for approximately 8 seconds until the computer restarts.
Note: To learn about advanced reset options, see the user guide.
Support
To search our knowledge base for a solution or log into the Technical Support
Portal and report a problem, go to
honeywell.com/PSStechnicalsupport.
Documentation
Product documentation is available at
sps.honeywell.com.
Limited Warranty
For warranty information, go to sps.honeywell.com
and click Support > Productivity > Warranties.
Patents
For patent information, see www.hsmpats.com.
Trademarks
Android is a trademark of Google LLC.
Other product names or marks mentioned in this document may be trademarks or
registered trademarks of other companies and are property of their respective
owners.
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in
specifications and other information contained in this document without prior
notice, and the reader should in all cases consult HII to determine whether
any such changes have been made. HII makes no representation or warranties
regarding the information provided in this publication.
HII shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from
the furnishing, performance, or use of this material. HII disclaims all
responsibility for the selection and use of software and/or hardware to
achieve intended results.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated into another language without the prior written
consent of HII.
Copyright © 2024 Honeywell Group of Companies.
All rights reserved.
References
- Honeywell SPS Community
- Industrial Automation | Honeywell
- Industrial Automation | Honeywell
- Industrial Automation | Honeywell
- Productivity products and associated patents | Honeywell