Beat-Sonic BSA49 Mobile Device Holder Instruction Manual

Beat-Sonic BSA49 Mobile Device Holder

Product Information

Specifications

• Stand Dimensions: 85mm(W) x 212mm(H) x 52mm(D)
• Material : ABS Plastic
• Holder Dimensions : 99mm(W) x 91mm(H) x 13mm(D)
• Material : ABS Plastic

Features

• Designed specifically for Toyota GR86 (ZN8) & Subaru BRZ (ZD8)
• Secure mounting position does not obstruct visibility or block air vents
• L-Bracket provides an option to attach a variety of Beat-Sonic mobile device holders

Dimension

Precautions

• Adjust Carefully: Ensure the mobile device does not interfere with the gear shift lever operation.
• Check Regularly: Extreme temperature changes and road vibrations may loosen the stand joints. Periodically check and tighten if necessary.
• Obey Traffic Laws: Follow local driving regulations, including those related to cell phone use while operating a vehicle.

Contents

• RHD GR86 / BRZ Stand x 1
• Self Closing Smartphone Holder x 1
• Protective Film x 2
• L-Bracket Stickers x 2
• Plastic Tweezers x 1
• Paper Template x 1
• Instruction Manual x 1

Product Usage Instructions

Apply Anti-Scratch Protective Film

1. Parallel to the edge of the passenger side gear shift surround trim, measure 14cm (5.5 in.) from the panel seam where the shift surround panel meets the center console box. Mark the location with masking tape.
2. On the lower section of the passenger side center console side panel, measure 9.5cm (3.74 in.) from the seam where the center console side panel joins the center console box. Apply another piece of masking tape to mark the location.
3. Apply the clear protective film strips to the plastic trim forward of the masking tape position markers, then remove the masking tape markers.

Install Stand

1. Remove the double-sided tape backing film from the stand and use tweezers if necessary.
2. Using the template as a guide, clip the lower edge of the stand under the center console side panel and clip the upper section of the stand over the gear shift surround trim.
3. Apply medium pressure to the side of the stand for at least 20 seconds to ensure strong adhesion of the double-sided tape. In cold weather, use a hair dryer to warm the mating surfaces.

Attach Holder

1. Complete the installation by attaching the mobile device holder to the stand.
2. If the holder does not fit tightly to the L-Bracket, apply 1-2 pieces of the supplied packing stickers to the back of the holder as shims to remove any play.

Using the Holder
Inserting the Phone: Insert the phone by lowering it into the holder. The weight of the phone will push down on the lower arm, and the side arms will automatically close to secure the phone in place.

Thank you for purchasing the Beat-Sonic BSA49 mobile device holder. Designed and made in Japan, this product represents our commitment to quality and excellence. Please read this manual carefully prior to installing this product to ensure correct operation.

Precautions

• Adjust Carefully: Ensure the mobile device does not interfere with the gear shift lever operation.
• Check Regularly: Extreme temperature changes and road vibrations may loosen the stand joints. Periodically check and tighten if necessary.
• Obey Traffic Laws: Follow local driving regulations, including those related to cell phone use while operating a vehicle.
• Disclaimer: Beat-Sonic and its affiliates are not responsible for any consequences resulting from the installation and/or use of this product.

Specifications

• Stand Dimensions:
  • 85mm(W) x 212mm(H) x 52mm(D)
  • Material : ABS Plastic
• Holder Dimensions:
  • 99mm(W) x 91mm(H) x 13mm(D)
  • Material : ABS Plastic

Contents

• RHD GR86 / BRZ Stand x 1
• Self Closing Smartphone Holder x 1
• Protective Film x 2
• L-Bracket Stickers x 2
• Plastic Tweezers x 1
• Paper Template x 1
• Instruction Manual x 1

Apply Anti-Scratch Protective Film

1. Parallel to the edge of the passenger side gear shift surround trim, measure 14cm (5.5 in.) from the panel seam where the shift surround panel meets the center console box. Mark the location with masking tape.
2. On the lower section of the passenger side center console side panel, measure 9.5cm (3.74 in.) from the seam where the center console side panel joins the center console box. Apply another piece of masking tape to mark the location.
3. Apply the clear protective film strips to the plastic trim forward of the masking tape position markers, as shown in the illustration on the right, then remove the masking tape markers.

Attach the Paper Template

1. Cut out the supplied paper template. Align the back edge of the template with the seam where the center console side panel joins the center console box. Use masking tape to temporarily hold in place.
2. Remove the double sided tape backing film from the stand. Using the template as a guide, (a) clip the lower edge of the stand under the center console side panel then (b) clip the upper section of the stand over the gear shift surround trim.
3. Apply medium pressure to the side of the stand for at least 20 seconds to ensure strong adhesion of the double sided tape. In cold weather, use a hair dryer to warm the mating surfaces

Attach the Holder

1. Complete the installation by attaching the mobile device holder to the stand If the holder does not fit tightly to the stand.
2. L-Bracket, apply 1 ~ 2 pieces as required of the supplied packing stickers to the back of the holder. The stickers act as shims to remove any play.

Using the Holder

• Inserting the Phone: Insert the phone by lowering it into the holder. The weight of the phone will push down on the lower arm, and the side arms will automatically close to secure the phone in place.
• Removing the Phone: Simply slide the phone upwards to release the arms.

Note : This holder design allows some movement of the phone even when the arms are closed. This is not a defect and is inherent to the design of this holder

International

• 472-5 Koushin, Fujieda, Nisshin, Aichi, 470-0112, JAPAN
• TEL : +81-561-75-1655
• FAX : +81-561-74-5595
• www.beatsonicglobal.com
• email : inquiries@beatsonicglobal.com

USA and Canada

• 14778 Beach Blvd. La Mirada, CA 90638
• TEL : 1-714-994-1085
• FAX : 1-714-249-4741
• www.beatsonicusa.com
• email: info@beatsonicusa.com

The rights to the trademarks, logos, trade names etc. herein belong to the respective owners. Refer to the Beat-Sonic website for details.

FAQ

Q: Is this product compatible with other car models?
A: No, this product is specifically designed for Toyota GR86 (ZN8) & Subaru BRZ (ZD8).

Q: How often should I check and tighten the stand joints?
A: It is recommended to check and tighten the stand joints periodically, especially after extreme temperature changes or prolonged use.

Q: What should I do if the mobile device holder does not fit tightly?
A: If the holder does not fit tightly, apply 1-2 pieces of the supplied packing stickers to the back of the holder to remove any play.

References

• BEAT-SONIC GLOBAL – Beat-Sonic Global
• BeatSonic USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>