ZEBRONICS ZEB Juke Bar 9102 Pro Soundbar with Subwoofer User Manual

ZEBRONICS ZEB Juke Bar 9102 Pro Soundbar with Subwoofer

Important Safety Instruction

Thank you for purchasing the ZEB-JUKE BAR 9102 PRO DOLBY. Please read this user manual carefully and keep for future reference.

Warning

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK)

Caution

• To reduce the risk of electric shock, do not dismantle the product and do not expose the apparatus to rain or moisture. No user­serviceable parts inside.
• Refer servicingto qualified personnel only.
• The lightning flash within an eq uilateral triangle is intended to alert you to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute an electric shock to a person or persons.
• Important! This symbol alerts you to read and observe important warnings and instructions on the unit or in this manual.

1. To prevent possible hearing damage, do not listen at high volume levels for long time periods or a sudden high volume level.
2. Never use the device unsupervised! Switch off the device whenever you are not using it, even if not using it only for a short while.
3. The appliance is not intended to be operated by means of an external timer or separate remote control system.
4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
5. Before operating this system, check the voltage of this system to see if it is identical to the voltage of your local power supply.
6. The unit should not be impeded by covering the ventilation opening with items such as newspaper, table-cloths, curtains etc. Make sure that there are at least 20 cm of space above and at least 5 cm of space on each side of the unit.
7. The apparatus must not be exposed to dripping or splashing liquid, no objects filled with liquids such as vases, should be placed on the apparatus.
8. To prevent fire or shock hazard, do not expose this equipment to direct heat, rain, moisture or dust.
9. Do not position this unit near any water sources e.g. taps, bathtubs, washing machines or swimming pools.
10. Ensure that you place the unit on a dry, stable surface.
11. Do not place this unit close to a strong magnetic field.
12. Do not place the unit on a amplifier or receiver.
13. Do not place this unit in a damp area as the moisture will affect the life of electric components.
14. Do not attempt to clean the unit with chemical solvents as this might damage the finish. Wipe with a clean, dry or slightly damp cloth.
15. When removing the power plug from the wall outlet, always pull directly on the plug, never pull on the cord.
16. Depending on the electromagnetic waves used by a television broadcast, if a TV is turned on near this unit while it is also on, lines might appear on the LED TV. Neither this unit nor the TV is malfunctioning. If you see such lines, keep this unit well away from the TV set.
17. The mains plug is used to disconnect the device, the disconnected device should remain readily operable.
18. Read these instructions. Keep these instructions. Follow all instructions. Heed all warnings.
19. Do not use this apparatus near water.
20. Clean only with dry cloth.
21. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
22. Do not install near any heat sources such as radiators, heaters, stoves, or other apparatus (including amplifiers)that produce heat.
23. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles or at the point where they exit from the apparatus.
24. Only use attachments/accessories specified by the manufacturer.
25. Unplug this apparatus during lightning storms or when unused for long periods of time.
26. Refer all servicing to qualified service personal. Servicing is required when the apparatus has been damage in any way, for example, when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
27.  Remove the Sound bar from the carton and remove all packing material from the Sound bar. Save the packing material, if possible, in case the Sound bar ever needs to be serviced or transported. The original carton and packing material is the only safe way to pack your Sound bar to protect it from damage in transit.
28. Remove any descriptive labels or stickers on the front or top of the cabinet. Do not remove any labels or stickers from the back or bottom of the cabinet.
29. Place your Sound bar on a level surface such as a table, desk or shelf, convenient to an AC outlet, out of direct sunlight, and away from sources of excess heat, dirt, dust, moisture, humidity, or vibration.
30. Unwind the Line cord connecting the AC adapter and extend it to its full length.
31. Remove any descriptive labels or stickers on the front or top of the cabinet. Do not remove any labels or stickers from the back or bottom of the cabinet.
32. Place your Sound bar on a level surface such as a table, desk or shelf, convenient to an AC outlet, out of direct sunlight, and away from sources of excess heat, dirt, dust, moisture, humidity, or vibration.
33. Unwind the Line cord connecting the AC adapter and extend it to its full length.

Protect Your Furniture

This model is equipped with non-skid rubber ‘feet’ to prevent the product from moving when you operate the controls. These ‘feet’ are made from non-migrating rubber material specially formulated to avoid leaving any marks or stains on your furniture. However certain types of oil based furniture polishes, wood preservatives, or cleaning sprays may cause the rubber ‘feet’ to soften, and leave marks or a rubber residue on the furniture.

To prevent any damage to your furniture we strongly recommend that you purchase small self-adhesive felt pads, available at hardware stores and home improvement center everywhere, and apply these pads to the bottom of the rubber ‘feet’ before you place the unit.

Important Notes

• Safety and operating instruction manual should be retained for future reference.
• The apparatus should not be exposed to dripping, splashing or placed in a humid atmosphere such as a bathroom.
• Do not install the product in the following areas:
• Places exposed to direct sunlight or close to radiators.
• On top of other stereo equipment that radiate too much heat -Blocking ventilation or in a dusty area.
• Areas where there is constant vibration.
• Humid or moist places.
• Do not place near candles or other flames.
• Operate the product only as instructed his manual.
•  Before turning on the power for the first time, make sure the sound bar is plugged to power outlet.
• For safety reasons, do not remove any covers or attempt to gain access to the inside of the product. Refer any servicing to qualified personnel.
• Do not attempt to remove any screws, or open the casing of the unit; there are no user serviceable parts inside. Refer all servicing to qualified service personnel.

Product Representation

Sound Bar & Sub-Woofer

1. LED Display
2. SWOUT
3. USB
4. AUX
5. OPTICAL
6. HDMl(ARC)
7. ACIN
8. Power/Standby
9. INPUT
10. VOL-
11. VOL+

Remote Control

Positioning the Sound Bar

Place on a flat Surface

Place the sound bar horizontally on a flat surface such as a TV unit or shelves and align it centrally with the TV screen. Allow some space between the speaker and the wall. Don’t place inside a cabinet or an a walled shelf. Follow this guidance for best sound output and good airflow around the sound bar.

Mounting the Wall

If you don’t feel confident to correctly and securely wall-mount the sound bar, Seek the assistance of an experienced person or professional.
Install the speaker on a vertical, fast, reinforced area of wall. For plaster walls, it is recommended to screw into wall studs for greater security. For optimum performance, allow at least 25mm/1″distance between the sound bar and the TV.

Follow below steps to mount the sound bar on the wall

1. Make 2 holes on the wall with distance same as the wall bracket on the sound bar
2. Put the plastic anchors onto the wall and secure the screws to the plastic clip, do not tighten the screws all the way make sure leave some space
3. Once the screws securely fastened, hang the sound bar over by inserting the screws onto the wall mount bracke

OPERATE INSTRUCTIONS

Setting the Sound bar

1. Plug in the power cord and the display will light up (Standby mode)
2. Switch on the soundbar by using power button on soundbar or by using STANDBY button on remote. After switching on, the default input mode will appear on display.
3. Input mode can be changed by pressing the input button again or by using the INPUT button on remote.
4. Below are input mode names appearing in the soundbar display:

BREATHING LED LIGHT COLOR SELECTION

1. When you connect with the sound bar to the power ,the screen goes into standby mode. Press the Power/Standby key and the soundbar will enter the mode selection.The LED light sources on both sides light up. Press the INPUT keyto selectthe mode you want.
2. Short press the breathing LED light button on the remote control and choose the colour to you like.

• MODE1: blue steady on /Pink on Red Steady on/Red steady on /Orange steady on /Green steady onlllght white steady on /Dark white steady on
• MODE2: Blue breathing /Purple breathing /Red breathing /Orange breathing /Green breathing /Pale white breathing /Deep white breathing
• MODE3:Monoctiromatic cyclic variation
• MODE4: Respiratory System

Powering On/Off

1. Plug the power cord of sound bar into a wall outlet, it will automatically enter standby mode
2. Short-press the “STANDBY” button on sound bar or on remote controller to turn on the sound bar
3. To turn off, press and hold the “STANDBY” button for 2 seconds, then unplug from wall outlet. 

Playing Audio via BT Connection

1. Turn on sound bar and then short-press the multi-function button to switch to BT mode and the LED will show BT
2. Activate the pairing function on your phone of other compatible device and select “ZEB-JUKE BAR 9102 PRO DOLBY”.
3. When successfully paired, you will hear a tone and the LED Display will stay on.
4. The remote control includes BT mode playback controls

Notes:

• If your pairing device switched off or manual disconnected, the sound bar will automatically enter pairing mode.
• If the connected device is switched off or manual disconnected, the sound bar will automatically enter.pairing successfully connected device will be re­established once you re-enter wireless range (10 meters). To connect to other devices, repeat the above pairing steps.

Playing Audio via use Port

The sound bar automatically switches to USB input mode with the LED display US when a USB flash drive is inserted (this mode isn’t selectable on the sound bar or remote control unless a USB flash drive is connected).

1. Ensure that your USB flash drive contains MP3 audio files (other file types not supported).
2. Connect the USB flash drive to the USB port on the sound bar (or your own USB extension cable connected to the USB port); music will automatically play.
3. The remote control includes USB input mode playback controls.

Audio input(Aux)Connection

1. Firstly connect the soundbar to your PC, laptop, smart-phone, TV, or other audio devices by using an AUX cable provided. Make sure that these devices have both AUX IN and AUX OUT terminals.
2. Then press the STANDBY button or INPUT button on remote control to switch the sound bar to Aux mode, once the soundbar is connected in Aux mode, the screen will display “AUX” . And the music on your connected device will play. Playback can only be controlled on your connected device.

Note: For some computers, you may need to access the audio control panel to manually set the soundbar as shown steps on above.

HDMI (ARC} Mode

1. The soundbar supports HDMI (ARC) with audio return channel (ARC). You can hear the TV audio through your soundbar by using a single HDMI (ARC) cable. But on condition that your TV is ARC compliant.

2. Using a high speed HDMI (ARC) cable, connect the HDMI (ARC) connector on the sound bar to the HDMI (ARC) connector on the TV. The HDMI (ARC) connector on the TV might be labeled differently. For details, see the user manual of yourTV.

3. When HDMI (ARC) is connected, TV sound setting in “sound output” mode should be set as , in addition, digital audio output mode should be set as or . When the HDMI (ARC) cable is connected, the TV digital audio output is set as Dolby or Auto mode. Then start playing music on the TV.

4. Press “INPUT” button on the remote control or “STANDBY” button on soundbar to select -HDMI (ARC) mode.
   Different TV might be different setting, please refer to yourTV User Manual.

5. Use the volume buttons to adjust the volume to your requirements.

6. You can also change the audio settings by using the relevant buttons on the remote control.

Note:

1. When connecting a device such as a TV/Set­top box/DVD/ game console with HDMI (ARC) cable, set the audio output mode of the device to Dolby or Auto mode <digital HDMI (ARC) output>.
2. The TV is connected to a HDMI (ARC) port with sound bar. Different TVs might have different setup menus,but the operation approach is the same.
3. If needs to connect set-up box meanwhile, please firstly connect the HDMI (ARC) connector and paired to the sound bar. Then connect the set-top box

Optical Mode

Remove the cap of optical cable (keep the cap for the future use); check the direction of the plug. Connect the soundbar and TV with the optical cable.

• Use this mode to play music from a TV with optical digital output on the sound bar. In TV sound settings, select the sound bar optical connection (output for audio). When the optical cable is connected, the TV audio output is set to Dolby or Auto mode.
• The TV must have an optical digital output. Use the optical cable to make the connection as follows:

1. 1. Connect the optical cable to the optical digital output of your TV.

2. Connect the optical cable to the optical digital input of your sound bar.

3. Switch on the TV set and the soundbar. Set theconnected TV to”Dolby or Auto mode”.

4. Start playing on the TV.

5. Press “IN PUT” button on the remote control or”STANDBY” button on the soundbar to select – OPTICAL mode.

6. Use the volume buttons to adjust the volume to your requirements.

7. You can also change the audio settings by using the relevant buttons on the remote control
   Note

8. When connecting a device such as a TV/Set­top box/ DVD/ game console with optical cable, set the audio output mode of the device to Dolby or Auto mode (digital optical output).

9. Do not bend the optical cable, otherwise the cable inside will be damaged.

Troubleshooting

Features

• (BT vS.0 I HDMI (ARC) I Optical IN I USB I AUX)
• Dolby Audio
• 16.51 cm Subwoofer
• Remote control
• LED Display
• Volume/Media Control
• Wall Mountable
• Sound Bar with Quad Drivers
• Glossy Finish

Specifications

• Output Power(RMS)
  • Subwoofer: 120W
  • Soundbar: 30Wx4
  • Total: :240W
• Driver Size
  • Subwoofer: 16.51 cm
  • Soundbar: (8.5×5.5)cmx4

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>