GERMAN POOL EFB-326H DC Motor SlimTower Bladeless Heater and Fan User Manual

DC Motor SlimTower
Bladeless Heater & Fan
EFB-326H
USER MANUAL

EFB-326H DC Motor SlimTower Bladeless Heater and Fan

Please read these instructions and warranty information carefully before use and keep them handy for future reference.

Online Warranty Registrationhttp://www.germanpool.com/warranty

Please register your warranty information now!
For Warranty Terms & Conditions, please refer to the last page of this user manual.

Warnings & Safety Instructions

Warnings!
To avoid fire, electric shock, or personal injury, please be sure to observe the following requirements;
Please follow the local electrical regulations.

• This product is only suitable for indoor use and should not be used outdoors.
• This product must not be repaired or modified by non-professional or unauthorized personnel.
• Before plugging in the power supply, please check whether the rated voltage indicated by this product is the same as the voltage in your home.
• When the machine is in operation or idle, it should be placed more than 1.5 meters away from fire and potential fire. Avoid direct sunlight.
• It is forbidden to use in places with flammables, or explosive objects, subject to heat, deformation, discoloration and deterioration. It is forbidden to use in places with heavy dust.
• It is forbidden to use in places with hanging objects, where it can be easily bumped into or hit, or on an unstable surface.
• It is forbidden to use the method of plugging (unplugging) the power cord to replace the power on and power off switch.
• It is forbidden to use this product as heating equipment for animals or plants.
• To avoid overheating, it is forbidden to cover the product.
• It is strictly forbidden to insert any wire or other foreign matter into any hole in the machine, in order to avoid electric shock.
• Do not use if the product shows signs of obvious damage after a fall.
• It is strictly forbidden to immerse the machine in water.
• Never use the machine directly facing an electrical outlet or under a power outlet.
• It is strictly forbidden to share the socket with other high-power appliances.
• Do not directly pull the power cord to move the body.
• If the machine is covered or incorrectly placed, it can cause a fire hazard. Therefore, it is not allowed to use a programmable automatic power-on device, timer, or any other device with the product.
• When the product is in use, the power cord should be placed behind the body. Placing the power cord in front will cause it to overheat and be damaged, or even cause an accident.
• Children, elderly people or patients who have lost the ability to take care of themselves, please use this appliance under the supervision of an adult, to prevent accidents.
• If this product fails, please turn off the power and unplug the power cord immediately. This product must be repaired by the manufacturer’s maintenance department or a similarly qualified professional.
• Before use, check that the power cord and the plug are in good condition. If the power cord is damaged, in order to avoid danger, the user must not disassemble or replace it. Replacing the power cord must be performed by the manufacturer’s maintenance department or a similarly qualified professional.
• To avoid burning when using this product, please do not let bare skin directly contact with the surface of the air outlet;
• This product is only suitable for use in dry environment. Do not use around the bathroom, a bath, a shower, sprinkler or swimming pool.
• If there is a gap between the plug and the socket, or the plug has become very hot, maybe the socket needs to be replaced. Consult a qualified electrician to replace the outlet.
• This product must be connected to a EMSD-HK-certified fixed socket with the correct rated power. It is strictly forbidden to use adopters, extension cords, or share the socket with other appliances.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not use this heater if it has been dropped.
• Do not use if there are visible signs of damage to the heater.
• WARNING! Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
• WARNING! To reduce the risk of fire, keep textiles, curtains or any other flammable material a minimum distance of 1 m from the air outlet.

Product Structure

This product uses PTC heating, send heat by hot air, which can quickly increase room temperature. It is without open flame, safe, efficient and energy saving.

1. Cover
2. Air Outlet
3. Air Duct
4. Body
5. Power Button
6. LED Display| 7. Air Inlet
8. Base
9. Power Cable
10. On / Off Switch
11. Remote Control
---|---

Getting Started

Location

• Please put this product in a horizontal position.
  Avoid putting it on a slope or a soft surface to prevent it from falling over. Please do not use it in high temperature area with high humidity, such as bathroom and kitchen.

• Avoid blocking the Air Inlet and Outlet during use. Please keep the product far away from the curtains, so that they will not block the Inlet/ Outlet and obstruct the product from working.

• Do not place objects within 1 meter in front of the Air Outlet to ensure that the volume of cool air would not be reduced. Pay attention to the effects on warm air blowing on objects.

CAUTION:
This product includes an Overheat Protection Sensor, which is an automatic fail-proof safety protection that cuts off power automatically when the product is accidentally tipped over or overheats. If this sensor is triggered and the product is stopped, unplug the machine and let it cool. Check and remove any obstructions before restarting the product and be sure to place it on a hard, level surface.

How To Change The Batteries Of The Remote Control

1. Open the Remote Control Battery Cover.
2. Remove old batteries and load two new AAA (No. 7) dry batteries.
3. Close the Battery Cover of the Remote Control.

WARNING!:

• Please keep batteries out of reach of children. If swallowed, please seek medical advice promptly.
• The batteries supplied with the product are not rechargeable. Non-rechargeable batteries are not to be recharged.
• Different types of batteries or new and used batteries are not to be mixed.
• Please insert the battery + – orientation correctly.
• If you do not use the Remote Control for a long time, remove the battery.
• Dispose of used batteries in accordance with local laws or regulations.

Operating Instructions

Turning On and Off

1. Insert the plug into the socket, turn on power switch and the product enters the standby state.
2. Press and hold Power Button for 1 second, the buzzer will beep once and the product start running.
3. Press and hold Power Button for 2 seconds, the buzzer will prompt you twice, and then stop running after you release the hand.

https://www.germanpool.com/chi/video_corner/?video=779

Air Volume Shift
When the machine is running in “Cool Mode”, press the “Power Button” in the Body to switch the air volume from 1 to 9.
When the machine is running in “Warm Mode”, press the “Power Button” in the Body to switch the air volume from 1 to 4.
(You can also use the “+ -” buttons on the left side of the Remote Control.)

Oscillating Operation
Press and hold the Power Button for 1 second, the buzzer will beep once and product start oscillating.
Press and hold the Power Button for 1 second again, the buzzer will beep once and product stop oscillating.

Remote Control

Button
---|---
Sleep Mode| Press “Sleep Mode” Button on the Remote Control.
The display shows “LL” and the fan speed becomes lowest.
Press again to exit the “Sleep Mode”.
(You can also exit the current mode by pressing the Wind Strength + button.)
High Cool| Press “High Cool” Button on the Remote Control.
The display shows “HH” and the fan speed become highest.
Press again to exit the Turbo Mode.
(You can also exit the current mode by pressing the Wind Strength + button.)
Oscillating| Press the “Oscillating” Button to turn on the Oscillation Function.
This fan can swing left and right at 80o. Press this button again to stop oscillating.
Sound| Press “Sound” Button to turn on/off the sound of fan. The sounds refer to the tone of turning on and off the fan using the Remote Control.
Cool Mode| During Cool Mode, the LED display is on with blue light.
Press this button to activate the Cool Mode.
Note: The default Start Mode is the Cool Mode.
Increase / Decrease Air Volume| Press the “+” Button on the left side of the Remote Control to increase the volume of air; press the “-” button on the left side of the Remote Control to decrease the volume of air.
Cool Mode can be used for 9-level settings, Warm Mode can be set for 4 levels.
Warm Mode| Press this “Warm Mode” Button to activate the Warm Mode.
The display number in Warm Mode is orange.
Note: During Warm Mode, both High Cool and Sleep Mode are not available.
Raise / Reduce Temperature| In Warm Mode, press the “+ -” Button on the right side of the Remote Control to set the Temperature (1-30°C).
Note: this button does not work during Cool Mode.
Timer| Press the “Timer” Button on the Remote Control to set 1 to 8 hours of timing.

Remote Control
The Remote Control should be pointed at the Remote Control Signal Receiver on the display to maximize the remote control signal. Effective distance: 5M.

Caution:
Remote Control error sometimes occurs due to the overlap of the channel frequencies. For example:

1. This product may react to the remote control of another appliances nearby; or
2. When using the remote control of this product, other electrical appliances may react.
   In order to avoid misuse, please operate this Remote Control away from any other appliances.

After switching the product to a standby mode, use the main switch in the product to power off, since using the Remote Control to turn it off would not cut off electricity completely. When the product is not in use for a long time, please unplug the power cord.

Warm Mode Instructions

1. Press the “Warm Mode” Button and the display shows the ambient temperature.
2. Press the “+ / -” on the right side to set the Temperature, and the digital display will be flashing, which can be set to 1-30°C.
3. 10 seconds after the desired temperature is set, the flashing will stop.
4. The temperature being set should be higher than the ambient temperature, so that the heating function will be turned on.
5. When the ambient temperature reaches the set temperature, the heating function will stop and turn into a cool breeze.
6. When ambient temperature dropped to be lower than the set temperature, the heating function will automatically be activated.

Set Temperature > Ambient Temperature: Warm Mode Turns On.
Set Temperature ≤ Ambient Temperature: Warm Mode Stops.

Note: The default temperature of the setting is 25 °C.
In the Warm Mode, when the ambient temperature is below 0°C, the display only shows 01, does not display negative temperature value.
The Warm Mode run over 9 hours, the machine will automatically stop running. Restart by pressing the host Power Button in the Body or by using the Remote Control.

Caution:
Please use Remote Control to set temperature; the Body of the product does not support this operation.

Cleaning & Maintenance

Caution: Unplug the power supply before performing maintenance.

Surface Cleaning

• Please do not put the product into water or splash it, which may cause the machine to be damaged.
• Do not use banana oil, benzine, alcohol, bleach or metal objects to wipe the surface of the fan, which may scratch the surface or cause discoloration.
• Wipe the surface with a soft, dry cloth. If it is very dirty, use water with a mild detergent and wipe with a soft cloth.Then wipe with a dry soft cloth.

Air Inlet/Outlet

• Use a soft brush or a vacuum cleaner to clean the dust at the Air Inlet and Outlet. Please clean it regularly to avoid the buildup of dust. Too much dust is not healthy and will reduce efficiency of the product.

Remote Control

• Gently wipe the surface of the Remote Control with a soft, dry cloth. If you don’t use the product for a long time, please remove the batteries inside the Remote Control to avoid battery consumption.

Storage

• If the product is not used for a long time, place it in a plastic bag after cleaning. Please avoid storing in a place with vibration (car trunk) or a place heated or cooled by another appliance. Please avoid placing it in direct sunlight, or a place with high temperature and/or high humidity. Please keep it out of reach of young children.

Troubleshooting

Caution: Do not disassemble the machine or repair it yourself.

inserted into the socket?
Remote Control does not work| Are the batteries dead?
Are the batteries inserted correctly?
Is the Remote Control aligned with the Signal Receiver?

Technical Specifications

Specifications are subject to change without prior notice.
If there is any inconsistency or ambiguity between the English version and the Chinese version, the Chinese version shall prevail.
Refer to www.germanpool.com for the most up-to- date version of the Operating Instructions.

Warranty Terms & Conditions

Under normal operations, the product will gurantee a 1-year full warranty provided by German Pool (effective from the date of purchase).

• This warranty is not valid until customer registration information is received by our Service Centre within 10 days of purchase via one of the following means:

  1. Visit our website and register online: www.germanpool.com/warranty
  2. Complete all the fields on the attached Warranty Card and mail it back to our Customer Service Centre.

Please fill out the form below. This information and the original purchase invoice will be required for any repairs. Warranty will be invalidated if information provided is found to be inaccurate.

Model No.: EFB-326H
Serial No.: —————— Invoice No.: ——————
Purchased From: —————— Purchase Date: ——————

1. Customer who fails to present original purchase invoice will not be eligible for free warranty service.

2. Customer should always follow the operating instructions. This warranty does not apply to:
   – labour costs for on-site installation, check-up, repair, replacement of parts and other transportation costs;
   – damages caused by accidents of any kind (including material transfer and others);
   – operating failures resulting from applying incorrect voltage, improper usage, and unauthorized installations or repairs.

3. This warranty is invalid if:
   – the purchase invoice is modified by an unauthorized party;
   – the product is used for any commercial or industrial purposes;
   – the product is repaired or modified by unauthorized personnel, or unauthorized parts are installed;
   – the serial number is modified, damaged or removed from the product.

4. German Pool will, at its discretion, repair or replace any defective part.

5. This warranty will be void if there is any transfer of ownership from the original purchaser.

Hong Kong, China
Unit B, G/F, Sunshine Kowloon Bay
Cargo Centre, 59 Tai Yip Street, Kowloon
Kowloon, Hong Kong
Tel : +852 2333 6249
Fax : +852 2356 9798
Email: repairs@germanpool.com| Macau,China
3/F, Edificio Industrial Pou Fung,
145 Rua de Francisco Xavier Pereira,
Macau
Tel : +853 2875 2699
Fax : +853 2875 2661
---|---

This warranty is valid only in Hong Kong and Macau

German Pool (Hong Kong) Limited

Hong Kong, China
Room 113, Newport Centre Phase II, 116 Ma Tau
Kok Road, Tokwawan, Kowloon, Hong Kong
Tel: +852 2773 2888
Fax: +852 2765 8215

Mainland China
8th, Xinxiang Road, Wusha Industrial Park,
Daliang, Shunde, Foshan, Guangdong
Tel: +86 757 2219 6888
Fax: +86 757 2219 6809

Macau, China
3/F, Edificio Industrial Pou Fung,
145 Rua de Francisco Xavier Pereira, Macau
Tel: +853 2875 2699
Fax: +853 2875 2661

© All rights reserved. Copying, reproducing or using the contents of this manual is not allowed without prior authorization from German Pool, violators will be prosecuted.

www.germanpool.com
EFB-326H-M-22(3.1)

References

• 德國寶German Pool | 家庭電器、廚櫃、傢俬 | 香港十大名牌

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>