Panasonic WW23A WWAN Module Adapter User Manual
- July 30, 2024
- Panasonic
Table of Contents
Panasonic WW23A WWAN Module Adapter
General
This device is the WWAN module adapter, WCDMA/LTE with Carrier Aggregation (CA)
Integration To The End Product
- Insert WW23A module into M.2 card connector.
- Secure the end of product using the screw.
- Insert Antenna unit into Antenna connectors of WW23A module.
Technical Specification
| a) Dimensions (H x W x D): | Approx. 2.3mm x 30mm x 42mm |
|---|---|
| b) Weight: | Approx. 6.5g |
| c) LTE Standard: | FDD: B2, B4, B5, B7, B12, B13, B14, B25, B26, B29(RX only), |
B66, B71 TDD: B41, B42(Canada only), B42(Canada only), B48
d) WCDMA Standard:| B2, B4, B5
e) Operating Temperature:| -30 to +70 degree Celsius
f) Connector interface:| M.2 3042-S3-B
g) Host interface:| USB interface etc.,
Regulatory Information
RF Exposure Compliance information
The WW23A module will have been granted modular approval for mobile applications. Integrators may use the WW23A module in their final products without additional FCC / ISED (Innovation, Science and Economic Development Canada) certification if they meet the following conditions. Otherwise, additional FCC / ISED approvals must be obtained.
- At least 20 cm separation distance between the antenna and the user’s body must be maintained at all times.
- To comply with FCC / ISED regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only exposure condition must not exceed the limits stipulated in Table 1.
Table 1 Antenna Gain and Collocated Radio Transmitter Specifications| Operating mode| TX Freq Range (MHz)| Max Conducted Power (dBm)| Antenna Gain Limit (dBi)| EIRP
Limits (dBm)
---|---|---|---|---|---
Standalone| Collocated
WW23A| WCDMA Band
2, LTE B2
| 1850| 1910| 24| 9.00| 7.30| 33.0
Embedded Module| WCDMA Band 4, LTE B4| 1710| 1755| 24| 6.00| 6.00| 30.0
| WCDMA Band 5, LTE B5| 824| 849| 24| 7.00| 4.90| 31.0
| LTE B7| 2500| 2570| 24| 9.00| 8.20| 33.0
| LTE B12| 699| 716| 24| 6.60| 4.50| 30.6
| LTE B13| 777| 787| 24| 6.90| 4.80| 30.9
| LTE B14| 788| 798| 24| 6.90| 4.80| 30.9
| LTE B25| 1850| 1915| 24| 9.00| 7.30| 33.0
| LTE B26| 814| 849| 24| 7.00| 4.90| 31.0
| LTE B41| 2496| 2690| 24| 9.00| 8.20| 33.0
| (Canada only) LTE B43| 3600| 3800| 23| 0.00| 0.00| 23.0
| LTE B48a| 3550| 3700| 23| 0.00| 0.00| 23.0
| LTE B66| 1710| 1780| 24| 6.00| 6.00| 30.0
| LTE B71| 663| 698| 24| 6.40| 4.30| 30.4
Collocated Transmitters| WLAN 2.4 GHz| 2400| 2500| | | | 30
WLAN 5 GHz| 5150| 5850| | | | 30
WLAN 6 GHz| 5955| 7115| | | | 30
Bluetooth| 2400| 2500| | | | 16
a. Important: Airborne operations in LTE Band 48 are prohibited.
- The WW23A module may transmit simultaneously with other collocated radio transmitters within a host device, provided the following conditions are met:
- Each collocated radio transmitter has been certified by FCC / ISED for mobile application.
- At least 20 cm separation distance between the antennas of the collocated transmitters and the user’s body must be maintained at all times.
- The radiated power of a collocated transmitter must not exceed the EIRP limit stipulated in Table 1.
A label must be affixed to the outside of the end product into which the WW23A module is incorporated, with a statement similar to the following:
- This device contains FCC ID: ACJ9TGWW23A, IC: 216H-CFWW23A .
Instructions to OEM Integrators
A user manual with the end product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC/ISED RF exposure guidelines.
The end product with an embedded WW23A module may also need to pass the FCC Part 15 unintentional emission testing requirements and be properly authorized per FCC Part 15.
If this module is intended for use in a portable device, integrators are responsible for separate evaluation and/or approval to satisfy FCC/ISED RF Exposure requirements.
If other radio devices are to be integrated with this module, an additional evaluation and ISED submission may be required. Integrators are responsible for such additional evaluation and ISED submission.
