Pushuntai WL03 Bicycle Anti Theft Sensor Alarm User Manual
- June 12, 2024
- Pushuntai
Table of Contents
Pushuntai WL03 Bicycle Anti Theft Sensor Alarm
MotorbikelBicycle Alti-Theft Alarm Remote Alarm / Displacement Sensor Alarm
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
- (1) This device may not cause harmful interference, and
- (2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE l: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Suppose this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. In that case, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio tv technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- External: Domineering power with tiger form styling and acts as a safeguard device to motorbike or bicycles.
- Similar performance to motorbike alarm, 113dB loudspeaker although installed at a hiding place to frighten the thief/robber.
- Use a triaxial accelerometer sensor and special calculation to increase the accuracy of robber manner recognition and reduce false alarms caused by noise interference.
- High efficient with 7 adjustable levels of sensitivity from soft touch to push beat and suitable for all conditions.
- 3 ringtones for remote bell sound; long range remote and easy to search the motorbike bicycle.
- Can trigger the SOS function and emit a call for help automatically when an accident occurs to provide a more safeguard manner.
- Wireless remote operation; more simple and more convenient to use.
- External Cover : PC material; IP55 water & dust proof
- The double-sided tape installation method is convenient for all types of motorbikes and bicycles.
External Structure figure
Cautions:
- Pay attention to host fixation method suitability, double-sided tape or cable tie when using it.
- Installation at a hiding location may reduce the host alarm sound level.
- Do not install the host surrounded by metal parts location.
Remote control have two below types according to order package set
Installation Guides
Host battery replacement and installation
Factory will install the battery by default. If the battery requires a
replacement or installs new batteries, please follows below figures method by
open bottom cover, install 3 pcs AAA alkaline battery. The host produce 3
times short ‘Bi’ sound and indicates turn on and use the host directly;
Recommend disassemble the battery if it does not use for long period of time.
Dismantle bottom cover method figure:
Remove the host’s Ipc bottom screw and use minus (-) screwdriver to
open the bottom cover by rotating or turning around. After opening the bottom
cover, continue to open the side of the cover until it is easily dismantled by
hand. If do not have a minus (-) screwdriver, can try use a solid film or shim
to open as shown in the above figure.
Application and Setting
ARM &DISARM
- Press once time on the remote control [ ] key in standby mode and the host produces “Do..Le..Mi” sound and enters into ARM mode, after 5 seconds, a ‘Bi ‘ sound and enters into alert mode. Any touch or hit occurs at ARM alert mode, the host will trigger the alarm immediately for 2 seconds, detect on any touch or hit again within 2— 12 seconds, the alarm will continue for 30 seconds (one ringtone type for 2 seconds alarm; 6 ringtones types for 30 seconds with automatic switching).
- Press the remote control [ ] key once at alert situation, the host will produce once “Mi..Le..Do” sound and signals the host was exited from alert mode already
- When the host is still alarming, direct press the remote control DISARM key to stop and exit from ARM mode simultaneously.
- Touch Sensitivity Level, Volume, SOS setting feature
- Touch sensitivity has 7 levels from high to low, 7 ringtone sound prompts, Do, Le, Mi, Fa, So, La, Di; Volume has 3 levels,high, medium and low.
- SOS is an internationally popular feature and off mode at the factory default setting. Note that the SOS function will recognize the installation state of the host,so please do not change the installation direction again after the installation, otherwise it may cause the function to fail or be abnormal. After the SOS function is turned on, it will automatically call of when the bicycle is tilted more than 45 degrees by accident. After corrected back the bicycle to the original position, it will turn off the call of automatically. The SOS trigger sound is in accordance with international conventions stand- dards.
Setting method
Press and hold the remote [ ], the host will continuously prompt the disarming
sound (please ignore the sound) until the remote LED light off and on again
before releasing the hand. The host enters into setting feature.
-
To adjust the sensitivity level, press [ ] key continuously from high to low in cycle with seven adjustable levels.
-
To adjust the volume, press the [ ] key continuously from high to low in cycle with 3 adjustable levels.
-
In case of the SOS function is turned off, press the [ ] key once, the host will “Bi” sound once to enter into the calibration mode, and then “Bi. Bi. Bi. Bi. Bi.” 5 beeps are correctly calibrated, and the SOS function is successfully turn on; Otherwise, two long “Bi… Bi” sounds is a calibration error and fail to turn on (The host shall be placed in static mode before performing the SOS calibration).
-
In case of the SOS function is turned on successfully, press the [ ] key once, a long”Bi” sound twice to turn off SOS function. After completing the setting, press [ ] key, the host will exit the setting function.
-
The host changes the batteries, sensitivity level and volume setting momeries will be stored. Because of SOS may needs to recalibrate, so it will automatically turn off.
-
Bell Ringtone switching function
Press [ ] key, 3 ringtones to choose and cyclic beeping (ARM mode can not use). -
Bell and search function:
Press bell key and trigger select- ed bell ringtone to find the motorbike/ bicycle easily. -
Remote control Learning Code
The first remote control code learning method: At first, remove the host batteries and install back after 30 seconds. Long press remote control [ ] key to enter the code learning mode. After the host produces once “Bid sound, press ARM or DISARM key with twice “3i..Bi..” sound, you should able to use new added remote control already. -
To add more remote controls code learning method:
Press old remote control’ s DISARM key to disarm at first, then,long press at old remote control [ to enter code learning mode, After once ‘Bi’ sound, press new remote control’ SARM or DISARM key with twice “Bi … Bi” sound, you should able to use new added remote control already. -
Decoding method: Be cautious when use this function! First, confirm the host is not at ARM mode; Long press for coded remote control [ ] key to enter into the code learning mode. After once ‘Bi’ sound, press [ ] key with “Bi … Bi … Bi “3 times sound, and the host will delete all coded addresses. Please refer to above method for new code learning.
-
Be cautious of the host can cater up to 8 remote control coding only, the first registered remote control coding will be removd if exceeds 8 remote controls registration.
-
Battery low power indication 2.2.6.1 When the host is at low battery (3.3V) condition, a weak “Du..Du..” 2 times sound was generated when use ARM or DISARM and requires to replace the battery immediately.
-
When the remote control’s flashlight becomes darklfade or the remote control range becomes shorter, it indicates the battery power is low and replaces with a new battery accordingly.
Operating Guides
- The host uses3 pcs AAA alkaline battery normal usage1-3 months; Standby (continuously): 6 months.
- WL03C: I pc 27A(12V) alkaline battery WL09C: Ipc CR2032(3V) button battery normal usage more than 1 year (Assume: 5 times usage/day)
- Operating environment temperatures: -20+60 C
- Operating environment humidity : RIH <80%
- Storage temperature: -30 C -+70 C
FCC Caution
This device complies With part 15 Of the FCC Rules. Operation is subject to
the following two conditions: (I) This device may not cause harmful
interference, and (2) this device must accept an interference received,
indudlng interference that may cause undesired operation. Any changes Or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class a digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with th instructions, may cause harmful interference to radio
communications. However, there is no guarantee that Interference Will ncfl
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an Oudet on a circuit different from that to which the receiver IS connected.
- Consult the dealer Or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.