PYLE PDWM812WH Wireless Handheld Microphone System User Guide

: July 27, 2024
: Pyle

Table of Contents

TRANSMITTER
RECEIVER
OPERATING THE TRANSMITTER
DISPLAY FUNCTION
OPERATING THE RECEIVER
RECEIVER INSTALLATION THE METHOD
PRECAUTIONS FOR USE
BLUETOOTH FUNCTION
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PYLE PDWM812WH Wireless Handheld Microphone System

PYLE PDWM812WH Wireless Handheld Microphone System

WIRELESS HANDHELD MICROPHONE SYSTEM SPECIFICATION

Please read carefully before use and keep for future reference.

TRANSMITTER

Power switch
Display screen
Frequency selective buttons
Battery case

RECEIVER

Front Panel

Mic C/6.35 Input port
Mic D/6.35 Input port
Volume adjustment for channel C
Volume adjustment for channel D
Volume adjustment for channel A
Volume adjustment for channel B
Echo adjustment
Music Volume adjustment
USB 2.1 input port
MP3 module display
Switch button (Bluetooth/MP3)
Power switch
Multi function button (Pause/Play/Next/Last)
Recording Button

Back Panel

Antenna for B channel
DC12V Power supply
6.35 Mixed output port
Right channel 6.35 output port
The left Channel 6.35 output port
Stereo 3.5mm Audio intput port
Stereo 3.5mm Audio output port
Antenna for A channel

OPERATING THE TRANSMITTER

Open the battery case according to the instruction and insert battery noting correct polarities (+ and –) indicated in the battery compartment.
Set the handheld switch to “ON” position, or press the switch. The microphone will display the frequency which means the microphone is turned ON. Turn the switch to “OFF” for turn off power or press the switch again. If there’s no frequency display that means the microphone is turned OFF.

DISPLAY FUNCTION

Display Function

NOTE:

The receiver and transmitter system should be with same channel (frequency) one by one, otherwise it will not work.

OPERATING THE RECEIVER

Rotate the antennas A and B to separate them by 90 degrees.
Connect the power base DC/AC
Audio output connection:
*Mixed non-equilibrium output, insert the end of audio cable to UN BAL AF OUT: 1:2 socket and insert to the other end of MIC IN or AUX IN socket from mixer or amplifier.
Turn ON the power switch, power indicator lights up.
When the handheld microphone is turned on, the “RF” indicator of the receiver lights up. Receiver output volume can be controlled by the volume control knob.

*Insert the voice line into UN BAL AF OUT* : socket 1, connect the other end into socket of MIC IN or AUX IN of mixer or amplifier, same operation type with another channel.
Independent balanced output BAL AF OUT** : 1 and 2 provide audio transmission three-pin card interface for professional mixer, ampiiers.

RECEIVER INSTALLATION THE METHOD

One meter above the ground.
Pull out all the antennas, otherwise it will aect the reception eect.
Be more than one meter away from the wall.

NOTICE

Frequency Conversion:
If you want to change the frequency during use, brietty press the frequency conversion key once.
The handheld microphone display fishes once, indicating that the frequency has been changed.
Frequency Lock:
In use, if you want the receiver to be able to use only one or specified Handheld microphone, please turn off the handheld microphone, and then do the following:
- Press the power switch to “ON” position, display 2 is lit,
  the receiver works normally.
- Press power switch 4 once, screen 6 brightness,
  microphone works normally
- Turn off the handheld microphone, press and hold the frequency selection button 3, then press and hold power switch 4 (about 5 seconds) until there is four horizontal (as shown in photo 6). On 5, release your hand and wait for 8 seconds, “RF” indicator turns off. 5 will turn off then automatically lights up, frequency lock operation completed.
  
  If the handheld is a toggle switch, just press the frequency conversion button for three seconds to lock the frequency.
  Note: To release the locking function, repeat the above operation.

PRECAUTIONS FOR USE

To ensure the receiving performance, avoid placing the host unit on the dead corner.
Do not throw the handheld microphone to avoid serious damage.
The machine body is not waterproof, please avoid water droplets or rain from entering the machine body.
Keep away from the electromagnetic eld, high-voltage transmission networks and large metal objects as far as possible.
Do not disassemble by yourself. The internal voltage may cause an electric shock to you.
When replacing the battery, be sure to press and hold the power button on the microphone until the screen turns off.
If the microphone is not used for a long time, please take out the battery to prevent battery leakage.
If the receiver is not used for a long time, please unplug the AC power plug.
If the machine falls apart or foreign matters enter the machine, do not continue to use it. Contact the local dealer or recognized service center immediately. Do not disassemble and repair by yourself. There is high voltage in the machine, which may cause you the risk of electric shock.
Keep the power adapter easy to operate. If the power adapter is not used for a long time, please unplug the AC power plug.
In order to protect the environment, please put the waste battery into the designated classified trash can or return it to the manufacturer. It can not be discarded directly. Do not put the battery or battery pack in the sun, fire baking, and other similar overheated environments.

NOTE: Make sure that the volume control is set to minimum position befor power is switched on. Loud noise produced at high volume when power is switched on can impair hearing

BLUETOOTH FUNCTION

When the receiver is turned on, the Bluetooth function is automatically turned on.
Turn on Bluetooth on your mobile phone, and search the Bluetooth name ’PYLEUSA’, click and pair.
Bluetooth and handheld input will be synchronized.
- Wireless BT Version: 4.2
- Wireless BT Range: 32’ ft

NOTICE:

All Pictures shown are for illustration purpose only. Actual product may vary due to product enhancement. *Pictures shown are for illustration purpose only.

FEATURES