greenworks PWA110 Compact Pressure Washer Instruction Manual

**greenworks PWA110 Compact Pressure Washer Instruction Manual

**

DESCRIPTION

PURPOSE

The machine is used to clean vehicles, boats, buildings by the removal of stubborn dirt with clean water and chemical detergents For domestic use only, not for professional use, and for operation at temperature above 0°C.

PRODUCT OVERVIEW

1. Upper handle
2. Power switch
3. Water intlet
4. Water outlet
5. Spray wand
6. Gun
7. Nozzle lock button
8. Trigger
9. Trigger safety button
10. Adjustable nozzle
11.  Spray tip cleaning tool
12. Garden hose
13. High pressure hose
14. Spring button
15. Detergent tank

GENERAL POWER TOOL SAFETY WARNINGS

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future
reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

INSTALLATION

UNPACK THE MACHINE

WARNING
Make sure that you correctly assemble the machine before use.

WARNING

• If parts of the machine are damaged, do not use the machine.
• If you do not have all the parts, do not operate the machine.
• If parts are damaged or missing, contact the service center.

1. Open the package.
2. Read the documentation provided in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and packing material in compliance with local regulations.

WARNING:
For your personal safety, do not insert battery before the tool is assembled completely.

INSTALL THE SPRAY WAND
Figure 2.

1. Push the end of the spray wand into the gun handle.
2. Turn the spray wand clockwise until the tabs lock into position.

WARNING:
Make sure that the connection has no leakage.

INSTALL THE WATER INLETCONNECTOR
Figure 3.

1. Install the water inlet connector onto the water inlet coupler.
2. Turn the water inlet connector clockwise until it is tight.

INSTALL THE UPPER HANDLE
Figure 4.

1.  Move the handle into the slots.
2. Put the screws into the holes.
3. Tighten the screws with a phillips head screwdriver (not included).

INSTALL THE HIGH PRESSURE
HOSE
Figure 5.

1. Push one end of the high pressure hose into the inlet coupler.

NOTE: Pull the spring button to release the high pressure hose.

1. Install and tighten the other end of the high pressure hose onto the water outlet coupler.

OPERATION

WARNING
Make sure that all the connections are tight and have no leakage before operation.

CONNECT THE WATER SUPPLY
TO THE MACHINE
For easy operation, please use a self-coiling garden hose (not provided).
WARNING
When you operate the self-coiling hose, make sure that the hose has no blockage.
WARNING

• The water supply must come from the water main
• Do not use hot water
• Do not use water from ponds or lakes

WARNING
Do the local regulations when you connect the garden hose to the water supply. Direct connection through a receiver tank or backflow preventer is usually permitted.
CAUTION
Inspect the filter in the water inlet connector before you connect the garden hose

• If the filter is damaged, do not use the machine until the filter is replaced.
• If the filter is dirty, clean the filter.

Figure 6.

• Uncoil the garden hose.
• Let the water flow through the garden hose for 30 seconds.
• Turn the water supply off.
• Install and tighten the end of the garden hose to the water inlet connector.

CAUTION
There must be a minimum of 3 m of free hose between the water inlet and the water supply.
4.2 USE THE GUN
Figure 2.

WARNING
For safe control, keep your hands on the gun at all times

• Pull and hold the gun trigger to start the machine.
• Release the gun trigger to stop water flow through the nozzle.

UNLOCK THE GUN TRIGGER

• Push backward the trigger safety button. 4.2.2 LOCK THE GUN TRIGGER
• Push forward the trigger safety button.

INSTALL THE NOZZLE
Figure 7.
WARNING
Before you change the nozzle:

1. Pull the gun trigger to release water pressure.
2. Lock the trigger safety button on the gun.
3. Stop the machine.

WARNING
Do not point the spray wand at your face or others’.

1.  Push and hold the lock button on the spray wand.
2.  Align the pin on the nozzle with the hole on the spray wand.
3. Install the nozzle onto the spray wand.
4. Rotate the nozzle to adjust the spray shape.

INSTALL THE DETERGENT TANK
Figure 8.

WARNING
Do not use household detergents, acids, alkalines, bleaches, solvents, flammable material, or industrial grade solutions, which can do damage to the pump.

WARNING
Do the instructions on the solution bottle to prepare detergent.

NOTE
If it is necessary, use a funnel to prevent the spill of detergent. Clean and dry the spilled detergent when you fill it.

1. Put the detergent into the detergent tank.
2.  Push and hold the lock button on the spray wand.
3. Install the detergent tank onto the spray wand.

NOTE
Do not let detergent dry on the surface to prevent streaks

1. START THE MACHINE
   Figure 9.
   CAUTION
   Do not operate without the water supply connected.

CAUTION
Before you start the machine:

1. Turn the water supply on.

2. Pull the gun trigger to release air pressure.

3. If a stable stream of water comes out from the gun, release the gun trigger.

4. Connect the machine to the power supply.

5. Set the power switch to the “ON” ( | ) position.

6. Turn the water supply on.

7. Pull the gun trigger.

STOP THE MACHINE

1. Release the gun trigger.
2. Set the power switch to the “OFF” (O) position.

WARNING
If you do not use the machine：

• Stop the machine.
• Turn the water supply off.
• Disconnect the power cord from the outlet.
• Pull the gun trigger to release the remaining pressure from the machine.
• Lock the trigger safety button.

MAINTENANCE

WARNING
Before maintenance, make sure that you

1. stop the machine.
2. wait until all the moving parts stop.
3. disconnect the plug from the power source.

WARNING
Do not use strong solvents or detergents on the plastic housing or components.

WARNING
Do not let brake fluids, gasoline, petroleum-based materials touch the plastic parts. Chemicals can cause damage to the plastic, and make the plastic unserviceable.

WARNING
Replace the power cord by an approved service center.

NOZZLE MAINTENANCE
Figure 6.
If there is too much pump pressure, the nozzle can become clogged, you can feel a pulsing sensation while you pull the gun trigger.

REMOVE THE NOZZLE

1. Push and hold the lock button on the spray wand.
2. Remove the nozzle from the spary wand.

CLEAN THE NOZZLE

1. Use a cleaning tool to clean the spray tip.
2. Flush and clean the unwanted materials out of the nozzle with the garden hose.
3. Install the clean nozzle to the spray wand.

TRANSPORTATION AND STORAGE

WARNING
Disconnect the power cord before transportation and storage.

MOVE THE MACHINE

• Point the spray wand in a safe direction.
• Only hold the machine with the handgrip.

STORE THE MACHINE
W ARNING
Make sure that the gun, the high pressure hose and the pump are dry.

WARNING
Make sure that children cannot come near the machine.

NOTE

Use a recommended pump protector to prevent cold weather damage during storage in winter.

• Disconnect the garden hose from machine.
• Wind the high pressure hose.
• Clean housing and the plastic components with a moist and soft cloth.
• Make sure that the machine does not have loose or damaged parts. If it is necessary, do these steps/ instructions:
• replace the damaged parts.
• tighten the bolts.
• speak to a person of an approved service center.
• Store the machine in a dry, isolated and frost-free area.

TROUBLESHOOTING

outlet.
The circuit breaker is trip- ped.| Let it cool, and start the ma- chine again.
The power switch is on, but you do not pull the gun trigger.| Pull the gun trig- ger.
The machine does not get high pressure.| The diameter of garden hose is too small.| Replace with a 1” (25 mm) or5/8” (16 mm) garden hose.
The garden hose is blocked.| Make sure that the garden hose is free from blockage.
The water supply is not sufficient.| Open the water suppy fully.
You do not install the nozzle onto the spray wand.| Install the nozzle onto the spray wand.
The water intake filter is blocked.| Remove the filter and make it clean in warm water.
PROBLEM| POSSIBLE CAUSE| SOLUTION
---|---|---
| The water supply is not sufficient.| Open water sup- py fully. Make sure the garden hose is free from blockage.
| The pump ab- sorbs air.| 1. Make sure that the ho- ses and fit- tings have no problem.
| | 2. Turn the ma- chine off.
** The output pres- sure varies high and low.| | 3. Pull the gun trigger until a stable flow of water comes out through the nozzle.
| The water intake filter is clogged.| Remove the filter and clean it in warm water.
| The supply volt- age is low.| Make sure that only the pres- sure washer op- erates on the cir- cuit.
| The gun, hose or nozzle are calci- fied.| Operate distilled vinegar through detergent tank.
PROBLEM| POSSIBLE CAUSE| SOLUTION**
---|---|---
The motor buz- zes, but you can not start the ma- chine.| The supply volt- age is low.| Make sure that only the pres- sure washer op- erates on the cir- cuit.
The system has remaining pres- sure.| 1.   Stop the ma- chine.2.   Pull the gun trigger on spray wand to release pressure3.   Start the ma- chine.
The voltage de- creases across extension cord.| Disconnect the extension cord, and connect the machine directly into the outlet.
You do not use the machine for a long time.| Speak to a per- son of an ap- proved service center.
There is remain- ing friction in components.You can hear a hum.| 1. Disconnect the water supply.2.   Turn the ma- chine on for 2 or 3 sec- onds.3. Repeat the above step for several times.
There is no wa- ter.| The water supply is off.| Turn the water supply on.
The garden hose is blocked.| Make sure that the garden hose is free from blockage.

 TECHNICAL DATA

WARRANTY

The full warranty terms and conditions can be found on
Greenworks website https://www.greenworkstools.eu)
The Greenworks warranty is 3 years on the product,
and 2 years on batteries (consumer/private usage)
from the date of purchase. This warranty covers
manufacturing faults. A faulty product under warranty
might be either repaired or replaced. A unit that has
been misused or used in other ways then described
in the owner’s manual might be rejected for warranty.
Normal wear, and wear parts are not considered as
warranty. The original manufacturer warranty is not
affected by any additional warranty offered by a dealer
or retailer.
A faulty product must be returned to the point of
purchase in order to claim for warranty, together with
the proof of purchase (receipt).

 EC DECLARATION OF CONFORMITY

Name and address of the manufacturer:
Name: GLOBGRO AB Globe Group Europe
Address : Riggaregatan 53, 211 13 Malmö, Sweden Herewith we declare that the product

Category : Pressure washer
Model : G30 (PWA110)
Serial number : See product rating label
Year of Construction: See product rating labe

is in conformity with the relevant provisions of the Machinery Directive 2006/42/EC.

• is in conformity with the provisions of the following other EC-Directives:
• 2014/30/EU
• 2000//14/EO＆2005/88/EO
• 2011/65/EU＆(EU)2015/863

Furthermore, we declare that the following (parts/clauses of) European harmonised standards have been used:
EN 60335-1, EN 60335-2-79, EN 62233:2008 EN 55014-1, EN 55014-2, EN 61000-3-3, EN 61000-3-3, EN ISO 3744, ISO 11094, IEC 62321-3-1, IEC 62321-4, IEC 62321-5, IEC 62321-6, IEC 62321-7-1, IEC 62321-7-2, IEC 62321-8
Conformity assessment method to Annex V/ Directive 2000/14/EC
Measured sound power level: 87.8 dB(A)
Guaranteed sound power level: 91 dB(A)
Place, date: Signature: Ted Qu, Quality Director
Malmö, 2018/3/15

References

• Powerful Cordless Gardening Tools | Greenworks Tools
• Greenworks | Battery-powered tools for your home & garden

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>